Interval Fuzzy Model for Robust Aircraft IMU Sensors Fault Detection

This paper proposes a data-based approach for a robust fault detection (FD) of the inertial measurement unit (IMU) sensors of an aircraft. Fuzzy interval models (FIMs) have been introduced for coping with the significant modeling uncertainties caused by poorly modeled aerodynamics. The proposed FIMs are used to compute robust prediction intervals for the measurements provided by the IMU sensors. Specifically, a nonlinear neural network (NN) model is used as central prediction of the sensor response while the uncertainty around the central estimation is captured by the FIM model. The uncertainty has been also modelled using a conventional linear Interval Model (IM) approach; this allows a quantitative evaluation of the benefits provided by the FIM approach. The identification of the IMs and of the FIMs was formalized as a linear matrix inequality (LMI) optimization problem using as cost function the (mean) amplitude of the prediction interval and as optimization variables the parameters defining the amplitudes of the intervals of the IMs and FIMs. Based on the identified models, FD validation tests have been successfully conducted using actual flight data of a P92 Tecnam aircraft by artificially injecting additive fault signals on the fault free IMU readings

Distributed Fault-Tolerant Consensus Tracking Control of Multi-Agent Systems under Fixed and Switching Topologies

This paper proposes a novel distributed fault-tolerant consensus tracking control design for multi-agent systems with abrupt and incipient actuator faults under fixed and switching topologies. The fault and state information of each individual agent is estimated by merging unknown input observer in the decentralized fault estimation hierarchy. Then, two kinds of distributed fault-tolerant consensus tracking control schemes with average dwelling time technique are developed to guarantee the mean-square exponential consensus convergence of multi-agent systems, respectively, on the basis of the relative neighboring output information as well as the estimated information in fault estimation. Simulation results demonstrate the effectiveness of the proposed fault-tolerant consensus tracking control algorithm

Control Design and Performance Analysis for Autonomous Formation Flight Experimentss

Autonomous Formation Flight is a key approach for reducing greenhouse gas emissions and managing traffic in future high density airspace. Unmanned Aerial Vehicles (UAV\u27s) have made it possible for the physical demonstration and validation of autonomous formation flight concepts inexpensively and eliminates the flight risk to human pilots. This thesis discusses the design, implementation, and flight testing of three different formation flight control methods, Proportional Integral and Derivative (PID); Fuzzy Logic (FL); and NonLinear Dynamic Inversion (NLDI), and their respective performance behavior. Experimental results show achievable autonomous formation flight and performance quality with a pair of low-cost unmanned research fixed wing aircraft and also with a solo vertical takeoff and landing (VTOL) quadrotor

Control Design and Performance Analysis for Autonomous Formation Flight Experiments

Autonomous Formation Flight is a key approach for reducing greenhouse gas emissions and managing traffic in future high density airspace. Unmanned Aerial Vehicles (UAV’s) have made it possible for the physical demonstration and validation of autonomous formation flight concepts inexpensively and eliminates the flight risk to human pilots. This thesis discusses the design, implementation, and flight testing of three different formation flight control methods, Proportional Integral and Derivative (PID); Fuzzy Logic (FL); and NonLinear Dynamic Inversion (NLDI), and their respective performance behavior. Experimental results show achievable autonomous formation flight and performance quality with a pair of low-cost unmanned research fixed wing aircraft and also with a solo vertical takeoff and landing (VTOL) quadrotor

Formal specification of requirements for analytical redundancy-based fault -tolerant flight control systems

Flight control systems are undergoing a rapid process of automation. The use of Fly-By-Wire digital flight control systems in commercial aviation (Airbus 320 and Boeing FBW-B777) is a clear sign of this trend. The increased automation goes in parallel with an increased complexity of flight control systems with obvious consequences on reliability and safety. Flight control systems must meet strict fault-tolerance requirements. The standard solution to achieving fault tolerance capability relies on multi-string architectures. On the other hand, multi-string architectures further increase the complexity of the system inducing a reduction of overall reliability.;In the past two decades a variety of techniques based on analytical redundancy have been suggested for fault diagnosis purposes. While research on analytical redundancy has obtained desirable results, a design methodology involving requirements specification and feasibility analysis of analytical redundancy based fault tolerant flight control systems is missing.;The main objective of this research work is to describe within a formal framework the implications of adopting analytical redundancy as a basis to achieve fault tolerance. The research activity involves analysis of the analytical redundancy approach, analysis of flight control system informal requirements, and re-engineering (modeling and specification) of the fault tolerance requirements. The USAF military specification MIL-F-9490D and supporting documents are adopted as source for the flight control informal requirements. The De Havilland DHC-2 general aviation aircraft equipped with standard autopilot control functions is adopted as pilot application. Relational algebra is adopted as formal framework for the specification of the requirements.;The detailed analysis and formalization of the requirements resulted in a better definition of the fault tolerance problem in the framework of analytical redundancy. Fault tolerance requirements and related certification procedures turned out to be considerably more demanding than those typically adopted in the literature. Furthermore, the research work brought up to light important issues in all fields involved in the specification process, namely flight control system requirements, analytical redundancy, and requirements engineering

Development of a Fuzzy Logic Model-Less Aircraft Controller

The Modeling and Control for Agile Aircraft Development (MCAAD) group at NASA Langley Research Center(LaRC) is developing techniques for Real-Time Global Modeling (RTGM) and Robust Learning Control (RLC) for NASA’s Transformational Tools and Technologies Project. This project seeks to develop a systematic approach to reduce the iterative nature of aircraft design by introducing a model-less control law and enabling inflight aerodynamic modeling and controller design. The development of the flight control system without prior knowledge of the aircraft aerodynamic model makes use of TakagiSugeno-Kang fuzzy logic inference systems for pitch and roll controllers and are tested in various simulations and wind tunnel platforms. These fuzzy logic controllers are not based on a mathematical model but rather on a rule base of generic flight control laws generated from the designer’s knowledge of aircraft flight mechanics. The controller architecture uses two channels to provide absolute and incremental controller commands as needed. The absolute channel is designed to reject disturbances and decrease rise time, while the incremental channel provides tracking and reduced steady state error. To provide controllers with acceptable performance without the need for tuning, a general method for selecting input and output scaling gains for the fuzzy inference systems is proposed. A performance and robustness comparison of similarly configured Type-1 and Interval Type-2 fuzzy logic controllers is made. The fuzzy logic controllers were implemented on an aircraft model in the NASA Langley 12-Foot low speed tunnel mounted on a free-to-pitch and free-to-roll rig. The development of the controller architectures and wind tunnel results are presented

Deep Learning-Based, Passive Fault Tolerant Control Facilitated by a Taxonomy of Cyber-Attack Effects

In the interest of improving the resilience of cyber-physical control systems to better operate in the presence of various cyber-attacks and/or faults, this dissertation presents a novel controller design based on deep-learning networks. This research lays out a controller design that does not rely on fault or cyber-attack detection. Being passive, the controller’s routine operating process is to take in data from the various components of the physical system, holistically assess the state of the physical system using deep-learning networks and decide the subsequent round of commands from the controller. This use of deep-learning methods in passive fault tolerant control (FTC) is unique in the research literature. The proposed controller is applied to both linear and nonlinear systems. Additionally, the application and testing are accomplished with both actuators and sensors being affected by attacks and /or faults

Design, Implementation and Testing of Advanced Control Laws for Fixed-wing UAVs

The present PhD thesis addresses the problem of the control of small fixed-wing Unmanned Aerial Vehicles (UAVs). In the scientific community much research is dedicated to the study of suitable control laws for this category of aircraft. This interest is motivated by the several applications that these platforms can perform and by their peculiarities as dynamical systems. In fact, small UAVs are characterized by highly nonlinear behavior, strong coupling between longitudinal and latero-directional planes, and high sensitivity to external disturbances and to parametric uncertainties. Furthermore, the challenge is increased by the limited space and weight available for the onboard electronics. The aim of this PhD thesis is to provide a valid confrontation among three different control techniques and to introduce an innovative autopilot configuration suitable for the unmanned aircraft field. Three advanced controllers for fixed-wing unmanned aircraft vehicles are designed and implemented: PID with H1 robust approach, L1 adaptive controller and nonlinear backstepping controller. All of them are analyzed from the theoretical point of view and validated through numerical simulations with a mathematical UAV model. One is implemented on a microcontroller board, validated through hardware simulations and tested in flight. The PID with H1 robust approach is used for the definition of the gains of a commercial autopilot. The proposed technique combines traditional PID control with an H1 loop shaping method to assess the robustness characteristics achievable with simple PID gains. It is demonstrated that this hybrid approach provides a promising solution to the problem of tuning commercial autopilots for UAVs. Nevertheless, it is clear that a tradeoff between robustness and performance is necessary when dealing with this standard control technique. The robustness problem is effectively solved by the adoption of an L1 adaptive controller for complete aircraft control. In particular, the L1 logic here adopted is based on piecewise constant adaptive laws with an adaptation rate compatible with the sampling rate of an autopilot board CPU. The control scheme includes an L1 adaptive controller for the inner loop, while PID gains take care of the outer loop. The global controller is tuned on a linear decoupled aircraft model. It is demonstrated that the achieved configuration guarantees satisfying performance also when applied to a complete nonlinear model affected by uncertainties and parametric perturbations. The third controller implemented is based on an existing nonlinear backstepping technique. A scheme for longitudinal and latero-directional control based on the combination of PID for the outer loop and backstepping for the inner loop is proposed. Satisfying results are achieved also when the nonlinear aircraft model is perturbed by parametric uncertainties. A confrontation among the three controllers shows that L1 and backstepping are comparable in terms of nominal and robust performance, with an advantage for L1, while the PID is always inferior. The backstepping controller is chosen for being implemented and tested on a real fixed-wing RC aircraft. Hardware-in-the-loop simulations validate its real-time control capability on the complete nonlinear model of the aircraft adopted for the tests, inclusive of sensors noise. An innovative microcontroller technology is employed as core of the autopilot system, it interfaces with sensors and servos in order to handle input/output operations and it performs the control law computation. Preliminary ground tests validate the suitability of the autopilot configuration. A limited number of flight tests is performed. Promising results are obtained for the control of longitudinal states, while latero-directional control still needs major improvements

Fuzzy Controllers

Trying to meet the requirements in the field, present book treats different fuzzy control architectures both in terms of the theoretical design and in terms of comparative validation studies in various applications, numerically simulated or experimentally developed. Through the subject matter and through the inter and multidisciplinary content, this book is addressed mainly to the researchers, doctoral students and students interested in developing new applications of intelligent control, but also to the people who want to become familiar with the control concepts based on fuzzy techniques. Bibliographic resources used to perform the work includes books and articles of present interest in the field, published in prestigious journals and publishing houses, and websites dedicated to various applications of fuzzy control. Its structure and the presented studies include the book in the category of those who make a direct connection between theoretical developments and practical applications, thereby constituting a real support for the specialists in artificial intelligence, modelling and control fields