Performance evaluation of secondary control policies with respect to digital communications properties in inverter-based islanded microgrids

A key challenge for inverted-based microgrids working in islanded mode is to maintain their own frequency and voltage to a certain reference values while regulating the active and reactive power among distributed generators and loads. The implementation of frequency and voltage restoration control policies often requires the use of a digital communication network for real-time data exchange (tertiary control covers the coordi- nated operation of the microgrid and the host grid). Whenever a digital network is placed within the loop, the operation of the secondary control may be affected by the inherent properties of the communication technology. This paper analyses the effect that properties like transmission intervals and message dropouts have for four existing representative approaches to secondary control in a scalable islanded microgrid. The simulated results reveals pros and cons for each approach, and identifies threats that properly avoided or handled in advance can prevent failures that otherwise would occur. Selected experimental results on a low- scale laboratory microgrid corroborate the conclusions extracted from the simulation study.Peer ReviewedPostprint (author's final draft

Switching frequency regulation in sliding mode control by a hysteresis band controller

© 2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other worksFixing the switching frequency is a key issue in sliding mode control implementations. This paper presents a hysteresis band controller capable of setting a constant value for the steady-state switching frequency of a sliding mode controller in regulation and tracking tasks. The proposed architecture relies on a piecewise linear modeling of the switching function behavior within the hysteresis band, and consists of a discrete-time integral-type controller that modifies the amplitude of the hysteresis band of the comparator in accordance with the error between the desired and the actually measured switching period. For tracking purposes, an additional feedforward action is introduced to compensate the time variation of the switching function derivatives at either sides of the switching hyperplane in the steady state. Stability proofs are provided, and a design criterion for the control parameters to guarantee closed-loop stability is subsequently derived. Numerical simulations and experimental results validate the proposal.Accepted versio

Hybrid and modular multilevel converter designs for isolated HVDC–DC converters

Efficient medium and high-voltage dc-dc conversion is critical for future dc grids. This paper proposes a hybrid multilevel dc-ac converter structure that is used as the kernel of dc-dc conversion systems. Operation of the proposed dc-ac converter is suited to trapezoidal ac-voltage waveforms. Quantitative and qualitative analyses show that said trapezoidal operation reduces converter footprint, active and passive components' size, and on-state losses relative to conventional modular multilevel converters. The proposed converter is scalable to high voltages with controllable ac-voltage slope; implying tolerable dv/dt stresses on the converter transformer. Structural variations of the proposed converter with enhanced modularity and improved efficiency will be presented and discussed with regards to application in front-to-front isolated dc-dc conversion stages, and in light of said trapezoidal operation. Numerical results provide deeper insight of the presented converter designs with emphasis on system design aspects. Results obtained from a proof-of-concept 1-kW experimental test rig confirm the validity of simulation results, theoretical analyses, and simplified design equations presented in this paper. - 2013 IEEE.Scopu

A three-switch high-voltage converter

A novel single active switch two-diodes high-voltage converter is presented. This converter can operate into a capacitor-diode voltage multiplier, which offers simpler structure and control, higher efficiency, reduced electromagnetic interference (EMI), and size and weight savings compared with traditional switched-mode regulated voltage multipliers. Two significant advantages are the continuous input current and easy isolation extension. The new converter is experimentally verified. Both the steady-state and dynamic theoretical models are correlated well with the experimental dat

Battery Charge Applications Based on Wide Output Voltage Range

In this study, high efficiency design procedure of a phase shifted full bridge (PSFB) converter is presented for on-board electrical vehicle (EV) battery charger. Presented design methodology used lithium-ion battery cells because of their high voltage and current rates compared to a lead-acid battery cells. In this case, PSFB converter can be regulated wide range output voltage with while its soft switching operation is maintained. The basic operation principles of PSFB converter is defined and its soft switching operation requirements are given. To evaluate the performance of the converter over wide output voltage range, zero voltage switching (ZVS) operation of converter is discussed based on dead time requirement. To improve efficiency, the snubber inductance effects on soft switching over wide output voltage range are evaluated. Finally, operation of the PSFB converter is validated experimentally with a prototype which has 42-54 V/15 A output range at 200 kHz switching frequency

Flying-capacitor multilevel converter voltage balance dynamics for pure resistive load

Multilevel converters need voltage balancing to be able to generate an output voltage with high quality. Flying capacitor converter topology has a natural voltage balancing property. Voltage balance dynamics analytical research methods reported to date are essentially based on a frequency domain analysis using double fourier transform. These complicated methods are not truly analytical, which makes an understanding of parameter influence on time constants difficult. In this paper, a straightforward time domain approach based on stitching of switch intervals piece-wise analytical solutions to a DC modulated H-bridge flying capacitor converter is discussed. This method allows to obtain time-averaged discrete and continuous voltage balance dynamics models. Using small-parameter approximation for pure resistive loads, simple and accurate expressions for voltage balance time constants are deduced, revealing their dependence on load parameters, carrier frequency and duty ratio

Multisource power splitting energy harvesting relaying network in half-duplex system over block Rayleigh fading channel: System performance analysis

Energy harvesting and information transferring simultaneously by radio frequency (RF) is considered as the novel solution for green-energy wireless communications. From that point of view, the system performance (SP) analysis of multisource power splitting (PS) energy harvesting (EH) relaying network (RN) over block Rayleigh-fading channels is presented and investigated. We investigate the system in both delay-tolerant transmission (DTT), and delay-limited transmission (DLT) modes and devices work in the half-duplex (HD) system. In this model system, the closed-form (CF) expressions for the outage probability (OP), system throughput (ST) in DLT mode and for ergodic capacity (EC) for DTT mode are analyzed and derived, respectively. Furthermore, CF expression for the symbol errors ratio (SER) is demonstrated. Then, the optimal PS factor is investigated. Finally, a Monte Carlo simulation is used for validating the analytical expressions concerning with all system parameters (SP).Web of Science81art. no. 6

Nonlinear Control of a DC MicroGrid for the Integration of Photovoltaic Panels

New connection constraints for the power network (Grid Codes) require more flexible and reliable systems, with robust solutions to cope with uncertainties and intermittence from renewable energy sources (renewables), such as photovoltaic arrays. The interconnection of such renewables with storage systems through a Direct Current (DC) MicroGrid can fulfill these requirements. A "Plug and Play" approach based on the "System of Systems" philosophy using distributed control methodologies is developed in the present work. This approach allows to interconnect a number of elements to a DC MicroGrid as power sources like photovoltaic arrays, storage systems in different time scales like batteries and supercapacitors, and loads like electric vehicles and the main AC grid. The proposed scheme can easily be scalable to a much larger number of elements.Comment: arXiv admin note: text overlap with arXiv:1607.0848