Using Fine Grain Approaches for highly reliable Design of FPGA-based Systems in Space

Nowadays using SRAM based FPGAs in space missions is increasingly considered due to their flexibility and reprogrammability. A challenge is the devices sensitivity to radiation effects that increased with modern architectures due to smaller CMOS structures. This work proposes fault tolerance methodologies, that are based on a fine grain view to modern reconfigurable architectures. The focus is on SEU mitigation challenges in SRAM based FPGAs which can result in crucial situations

Radiation hard FPGA configuration techniques using silicon on sapphire

 Once entirely the domain of space-borne applications, the effects of high energy charged particles on electronics systems is now also a concern for terrestrial devices. Reconfigurable components such as FPGAs are particularly vulnerable to radiation single event effects (SEU) as they carry a large amount of memory within a relatively small amount of circuit area. This thesis presents a Silicon on Insulator (SOI) based configuration memory system in a radiation hard reconfiguration system. The SOI technology used in this particular work is Silicon on Sapphire, where Sapphire is used as the body insulator. A non-volatile storage cell, able to be manufactured in a standard single polysilicon SOI CMOS process with no special layers, is combined with a Schmitt amplifier which result a final structure that exhibits two unique characteristics enhancing its resistance to radiation. Firstly, it is impossible for a radiation induced event to permanently flip the configuration state. Secondly, a partial de-programming resulting in a reduction in the magnitude of the storage cell voltage causes a large change in static current that can be very easily detected using a conventional sense amplifier. A simple current detector of the type used in conventional RAM circuits allows the configuration memory to be set up to exhibit self-correcting, or “auto-scrubbing” behavior. While the combination of SOI EEPROM and Schmitt exhibits high intrinsic resistance to radiation induced errors, it is still possible for a sequence of two particle strikes to cause the configuration value to be lost. Estimates are made of the Soft error Rate (SER) performance of the overall configuration memory structure. A trial layout of a configurable Look Up Table (LUT) is presented as an example of how the SOS EEPROM configuration cell would be deployed in a real system

Characterisation and mitigation of long-term degradation effects in programmable logic

Reliability has always been an issue in silicon device engineering, but until now it has been managed by the carefully tuned fabrication process. In the future the underlying physical limitations of silicon-based electronics, plus the practical challenges of manufacturing with such complexity at such a small scale, will lead to a crunch point where transistor-level reliability must be forfeited to continue achieving better productivity. Field-programmable gate arrays (FPGAs) are built on state-of-the-art silicon processes, but it has been recognised for some time that their distinctive characteristics put them in a favourable position over application-specific integrated circuits in the face of the reliability challenge. The literature shows how a regular structure, interchangeable resources and an ability to reconfigure can all be exploited to detect, locate, and overcome degradation and keep an FPGA application running. To fully exploit these characteristics, a better understanding is needed of the behavioural changes that are seen in the resources that make up an FPGA under ageing. Modelling is an attractive approach to this and in this thesis the causes and effects are explored of three important degradation mechanisms. All are shown to have an adverse affect on FPGA operation, but their characteristics show novel opportunities for ageing mitigation. Any modelling exercise is built on assumptions and so an empirical method is developed for investigating ageing on hardware with an accelerated-life test. Here, experiments show that timing degradation due to negative-bias temperature instability is the dominant process in the technology considered. Building on simulated and experimental results, this work also demonstrates a variety of methods for increasing the lifetime of FPGA lookup tables. The pre-emptive measure of wear-levelling is investigated in particular detail, and it is shown by experiment how di fferent reconfiguration algorithms can result in a significant reduction to the rate of degradation

Fault-tolerant fpga for mission-critical applications.

One of the devices that play a great role in electronic circuits design, specifically safety-critical design applications, is Field programmable Gate Arrays (FPGAs). This is because of its high performance, re-configurability and low development cost. FPGAs are used in many applications such as data processing, networks, automotive, space and industrial applications. Negative impacts on the reliability of such applications result from moving to smaller feature sizes in the latest FPGA architectures. This increases the need for fault-tolerant techniques to improve reliability and extend system lifetime of FPGA-based applications. In this thesis, two fault-tolerant techniques for FPGA-based applications are proposed with a built-in fault detection region. A low cost fault detection scheme is proposed for detecting faults using the fault detection region used in both schemes. The fault detection scheme primarily detects open faults in the programmable interconnect resources in the FPGAs. In addition, Stuck-At faults and Single Event Upsets (SEUs) fault can be detected. For fault recovery, each scheme has its own fault recovery approach. The first approach uses a spare module and a 2-to-1 multiplexer to recover from any fault detected. On the other hand, the second approach recovers from any fault detected using the property of Partial Reconfiguration (PR) in the FPGAs. It relies on identifying a Partially Reconfigurable block (P_b) in the FPGA that is used in the recovery process after the first faulty module is identified in the system. This technique uses only one location to recover from faults in any of the FPGA’s modules and the FPGA interconnects. Simulation results show that both techniques can detect and recover from open faults. In addition, Stuck-At faults and Single Event Upsets (SEUs) fault can also be detected. Finally, both techniques require low area overhead

Radiation Tolerant Electronics, Volume II

Research on radiation tolerant electronics has increased rapidly over the last few years, resulting in many interesting approaches to model radiation effects and design radiation hardened integrated circuits and embedded systems. This research is strongly driven by the growing need for radiation hardened electronics for space applications, high-energy physics experiments such as those on the large hadron collider at CERN, and many terrestrial nuclear applications, including nuclear energy and safety management. With the progressive scaling of integrated circuit technologies and the growing complexity of electronic systems, their ionizing radiation susceptibility has raised many exciting challenges, which are expected to drive research in the coming decade.After the success of the first Special Issue on Radiation Tolerant Electronics, the current Special Issue features thirteen articles highlighting recent breakthroughs in radiation tolerant integrated circuit design, fault tolerance in FPGAs, radiation effects in semiconductor materials and advanced IC technologies and modelling of radiation effects

Analyse und Erweiterung eines fehler-toleranten NoC für SRAM-basierte FPGAs in Weltraumapplikationen

Data Processing Units for scientific space mission need to process ever higher volumes of data and perform ever complex calculations. But the performance of available space-qualified general purpose processors is just in the lower three digit megahertz range, which is already insufficient for some applications. As an alternative, suitable processing steps can be implemented in hardware on a space-qualified SRAM-based FPGA. However, suitable devices are susceptible against space radiation. At the Institute for Communication and Network Engineering a fault-tolerant, network-based communication architecture was developed, which enables the construction of processing chains on the basis of different processing modules within suitable SRAM-based FPGAs and allows the exchange of single processing modules during runtime, too. The communication architecture and its protocol shall isolate non SEU mitigated or just partial SEU mitigated modules affected by radiation-induced faults to prohibit the propagation of errors within the remaining System-on-Chip. In the context of an ESA study, this communication architecture was extended with further components and implemented in a representative hardware platform. Based on the acquired experiences during the study, this work analyses the actual fault-tolerance characteristics as well as weak points of this initial implementation. At appropriate locations, the communication architecture was extended with mechanisms for fault-detection and fault-differentiation as well as with a hardware-based monitoring solution. Both, the former measures and the extension of the employed hardware-platform with selective fault-injection capabilities for the emulation of radiation-induced faults within critical areas of a non SEU mitigated processing module, are used to evaluate the effects of radiation-induced faults within the communication architecture. By means of the gathered results, further measures to increase fast detection and isolation of faulty nodes are developed, selectively implemented and verified. In particular, the ability of the communication architecture to isolate network nodes without SEU mitigation could be significantly improved.Instrumentenrechner für wissenschaftliche Weltraummissionen müssen ein immer höheres Datenvolumen verarbeiten und immer komplexere Berechnungen ausführen. Die Performanz von verfügbaren qualifizierten Universalprozessoren liegt aber lediglich im unteren dreistelligen Megahertz-Bereich, was für einige Anwendungen bereits nicht mehr ausreicht. Als Alternative bietet sich die Implementierung von entsprechend geeigneten Datenverarbeitungsschritten in Hardware auf einem qualifizierten SRAM-basierten FPGA an. Geeignete Bausteine sind jedoch empfindlich gegenüber der Strahlungsumgebung im Weltraum. Am Institut für Datentechnik und Kommunikationsnetze wurde eine fehlertolerante netzwerk-basierte Kommunikationsarchitektur entwickelt, die innerhalb eines geeigneten SRAM-basierten FPGAs Datenverarbeitungsmodule miteinander nach Bedarf zu Verarbeitungsketten verbindet, sowie den Austausch von einzelnen Modulen im Betrieb ermöglicht. Nicht oder nur partiell SEU mitigierte Module sollen bei strahlungsbedingten Fehlern im Modul durch das Protokoll und die Fehlererkennungsmechanismen der Kommunikationsarchitektur isoliert werden, um ein Ausbreiten des Fehlers im restlichen System-on-Chip zu verhindern. Im Kontext einer ESA Studie wurde diese Kommunikationsarchitektur um Komponenten erweitert und auf einer repräsentativen Hardwareplattform umgesetzt. Basierend auf den gesammelten Erfahrungen aus der Studie, wird in dieser Arbeit eine Analyse der tatsächlichen Fehlertoleranz-Eigenschaften sowie der Schwachstellen dieser ursprünglichen Implementierung durchgeführt. Die Kommunikationsarchitektur wurde an geeigneten Stellen um Fehlerdetektierungs- und Fehlerunterscheidungsmöglichkeiten erweitert, sowie um eine hardwarebasierte Überwachung ergänzt. Sowohl diese Maßnahmen, als auch die Erweiterung der Hardwareplattform um gezielte Fehlerinjektions-Möglichkeiten zum Emulieren von strahlungsinduzierten Fehlern in kritischen Komponenten eines nicht SEU mitigierten Prozessierungsmoduls werden genutzt, um die tatsächlichen auftretenden Effekte in der Kommunikationsarchitektur zu evaluieren. Anhand der Ergebnisse werden weitere Verbesserungsmaßnahmen speziell zur schnellen Detektierung und Isolation von fehlerhaften Knoten erarbeitet, selektiv implementiert und verifiziert. Insbesondere die Fähigkeit, fehlerhafte, nicht SEU mitigierte Netzwerkknoten innerhalb der Kommunikationsarchitektur zu isolieren, konnte dabei deutlich verbessert werden

Robust design of deep-submicron digital circuits

Avec l'augmentation de la probabilité de fautes dans les circuits numériques, les systèmes développés pour les environnements critiques comme les centrales nucléaires, les avions et les applications spatiales doivent être certifies selon des normes industrielles. Cette thèse est un résultat d'une cooperation CIFRE entre l'entreprise Électricité de France (EDF) R&D et Télécom Paristech. EDF est l'un des plus gros producteurs d'énergie au monde et possède de nombreuses centrales nucléaires. Les systèmes de contrôle-commande utilisé dans les centrales sont basés sur des dispositifs électroniques, qui doivent être certifiés selon des normes industrielles comme la CEI 62566, la CEI 60987 et la CEI 61513 à cause de la criticité de l'environnement nucléaire. En particulier, l'utilisation des dispositifs programmables comme les FPGAs peut être considérée comme un défi du fait que la fonctionnalité du dispositif est définie par le concepteur seulement après sa conception physique. Le travail présenté dans ce mémoire porte sur la conception de nouvelles méthodes d'analyse de la fiabilité aussi bien que des méthodes d'amélioration de la fiabilité d'un circuit numérique.The design of circuits to operate at critical environments, such as those used in control-command systems at nuclear power plants, is becoming a great challenge with the technology scaling. These circuits have to pass through a number of tests and analysis procedures in order to be qualified to operate. In case of nuclear power plants, safety is considered as a very high priority constraint, and circuits designed to operate under such critical environment must be in accordance with several technical standards such as the IEC 62566, the IEC 60987, and the IEC 61513. In such standards, reliability is treated as a main consideration, and methods to analyze and improve the circuit reliability are highly required. The present dissertation introduces some methods to analyze and to improve the reliability of circuits in order to facilitate their qualification according to the aforementioned technical standards. Concerning reliability analysis, we first present a fault-injection based tool used to assess the reliability of digital circuits. Next, we introduce a method to evaluate the reliability of circuits taking into account the ability of a given application to tolerate errors. Concerning reliability improvement techniques, first two different strategies to selectively harden a circuit are proposed. Finally, a method to automatically partition a TMR design based on a given reliability requirement is introduced.PARIS-Télécom ParisTech (751132302) / SudocSudocFranceF

Circuit Design, Architecture and CAD for RRAM-based FPGAs

Field Programmable Gate Arrays (FPGAs) have been indispensable components of embedded systems and datacenter infrastructures. However, energy efficiency of FPGAs has become a hard barrier preventing their expansion to more application contexts, due to two physical limitations: (1) The massive usage of routing multiplexers causes delay and power overheads as compared to ASICs. To reduce their power consumption, FPGAs have to operate at low supply voltage but sacrifice performance because the transistors drive degrade when working voltage decreases. (2) Using volatile memory technology forces FPGAs to lose configurations when powered off and to be reconfigured at each power on. Resistive Random Access Memories (RRAMs) have strong potentials in overcoming the physical limitations of conventional FPGAs. First of all, RRAMs grant FPGAs non-volatility, enabling FPGAs to be "Normally powered off, Instantly powered on". Second, by combining functionality of memory and pass-gate logic in one unique device, RRAMs can greatly reduce area and delay of routing elements. Third, when RRAMs are embedded into datpaths, the performance of circuits can be independent from their working voltage, beyond the limitations of CMOS circuits. However, researches and development of RRAM-based FPGAs are in their infancy. Most of area and performance predictions were achieved without solid circuit-level simulations and sophisticated Computer Aided Design (CAD) tools, causing the predicted improvements to be less convincing. In this thesis,we present high-performance and low-power RRAM-based FPGAs fromtransistorlevel circuit designs to architecture-level optimizations and CAD tools, using theoretical analysis, industrial electrical simulators and novel CAD tools. We believe that this is the first systematic study in the field, covering: From a circuit design perspective, we propose efficient RRAM-based programming circuits and routing multiplexers through both theoretical analysis and electrical simulations. The proposed 4T(ransitor)1R(RAM) programming structure demonstrates significant improvements in programming current, when compared to most popular 2T1R programming structure. 4T1R-based routingmultiplexer designs are proposed by considering various physical design parasitics, such as intrinsic capacitance of RRAMs and wells doping organization. The proposed 4T1R-based multiplexers outperformbest CMOS implementations significantly in area, delay and power at both nominal and near-Vt regime. From a CAD perspective, we develop a generic FPGA architecture exploration tool, FPGASPICE, modeling a full FPGA fabric with SPICE and Verilog netlists. FPGA-SPICE provides different levels of testbenches and techniques to split large SPICE netlists, in order to obtain better trade-off between simulation time and accuracy. FPGA-SPICE can capture area and power characteristics of SRAM-based and RRAM-based FPGAs more accurately than the currently best analyticalmodels. From an architecture perspective, we propose architecture-level optimizations for RRAMbased FPGAs and quantify their minimumrequirements for RRAM devices. Compared to the best SRAM-based FPGAs, an optimized RRAM-based FPGA architecture brings significant reduction in area, delay and power respectively. In particular, RRAM-based FPGAs operating in the near-Vt regime demonstrate a 5x power improvement without delay overhead as compared to optimized SRAM-based FPGA operating at nominal working voltage

Wideband active envelope load-pull for robust power amplifier and transistor characterisation

The advent of fourth generation (4G) wireless communication with available modulation bandwidth ranging from 1 MHz to 20 MHz is starting to emerge. The linear modulation technique being employed means that the power amplifiers that support the standards need to have high degree of linearity. By nature, however, all power amplifiers are non-linear. Load-pull measurement system provides anindispensable non-linear tool for the characterization of power amplifier and transistor for linearity enhancement. Conventional passive or active load-pull has delay problem that get worse as the modulation frequency is increased beyond few MHz. Furthermore in order to provide robust non-linear measurement, load-pull system needs to provide bandwidth at least five times the modulation bandwidth by including the fifth-order inter-modulation (IMD5). This thesis presents, for the first time, delay compensation on the unique active envelope load-pull architecture providing constant impedance for bandwidth up to 20 MHz. In doing so, it provides a superior load-pull measurement and also the ability to directly control in-band impedances. Artificial variations imposed on the in-band impedances offer further insight on power amplifier and transistor behaviours under wideband multi-tone stimulus.EThOS - Electronic Theses Online ServiceGBUnited Kingdo