Embroidered textile frequency-splitting sensor based on stepped-impedance resonators

©2022 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.This paper presents an embroidered textile frequency-splitting microwave sensor based on a pair of identical stepped-impedance resonators (SIRs) loading a microstrip transmission line. The sensor is implemented by means of conductive threads. The sensing region of the proposed structure is the capacitive square patch of one of the SIRs. If such region is kept unaltered, the structure is symmetric, and the frequency response (transmission coefficient) exhibits a single transmission zero. However, if symmetry is broken (e.g., through liquid absorption in the sensing region), the frequency response of the proposed sensor exhibits two transmission zeros (frequency splitting). The difference (in frequency and magnitude) between such zeros (or notches) is intimately related to the dielectric properties of the absorbed liquids to be sensed / detected. The proposed sensing structure is applied to the detection of deionized (DI) water absorption, and to the quantification of the number of DI water drops. The maximum measured sensitivity is found to be 2.70 MHz /µl and 0.03 dB /µl for the incremental frequency and incremental magnitude of the notches.This work was supported by MICIIN-Spain (projects PID2019-103904RB-I00, TEC2016-79465-R, and PDC2021-121085-I00),Generalitat de Catalunya (project 2017SGR-1159), Institució Catalana de Recerca i Estudis Avançats (who awarded Ferran Martín), and by FEDER funds.Peer ReviewedPostprint (author's final draft

Microwave sensors based on resonant elements

This paper highlights interest in the implementation of microwave sensors based on resonant elements, the subject of a special issue in the journal. A classification of these sensors on the basis of the operating principle is presented, and the advantages and limitations of the different sensor types are pointed out. Finally, the paper summarizes the different contributions to the special issue

T-Junction Loaded with Interdigital Capacitor for Differential Measurement of Permittivity

The microwave sensors have been successfully used for permittivity measurement. These sensors suffer from limited sensitivity and environmental effects. This article presents a novel T-junction highly sensitive microwave sensor for permittivity measurement of low-loss solid materials. The proposed sensor operation principle is based on downshifting the transmission zero (TZ) of the outputs of T-junction with the coupling of the material under test (MUT). The sensing section consists of an interdigital capacitor (IDC) located in between the lines of the T-junction. IDC is directly connected to output arms of T-junction, so that it could disturb the outputs strongly. Any change in electric field concentration in IDC directly is transmitted to the outputs and is translated as TZ change. Design steps including T-junction and IDC effects on outputs are presented in detail. The sensor operation principle is described through an equivalent circuit model, which is validated by simulation and experimental results. Two outputs of the proposed sensor show the same electrical performances, which allow differential operation mode. Hence, cross sensitivity due to environmental factors can be tolerated by the sensor. Measurement results of the fabricated prototype show 112-MHz frequency shift per unit permittivity change and a normalized sensitivity of 3.9%, which are larger than available similar sensors. The proposed sensor is implemented on a 22.22 × 18.76 × 1.6 mm3 printed circuit board.</p

Highly sensitive phase variation sensors based on step-impedance coplanar waveguide (CPW) transmission lines

Reflective-mode step-impedance transmission line based sensors for dielectric characterization of solids or liquids have been recently proposed. In this article, in order to further increase the sensitivity, the sensor is implemented in coplanar waveguide (CPW technology), and this constitutes the main novelty of this work. The sensor thus consists of a high-impedance 90° (or low-impedance 180°) open-ended sensing line cascaded to a low-impedance 90° (or high-impedance 90°) line. The output variable is the phase of the reflection coefficient, which depends on the dielectric constant of the material under test (MUT), the input variable. Placing a MUT on top of the sensing line causes a variation in the effective dielectric constant of the line, thereby modifying the phase of such line. This in turn produces a multiplicative effect on the phase of the reflection coefficient, by virtue of the step-impedance discontinuity. The main advantage of the CPW-based sensor, over other similar sensors based on microstrip technology, is the stronger dependence of the phase velocity of the sensing line with the dielectric constant of the MUT, resulting in sensitivities as high as -45.48° in one of the designed sensors. The sensor is useful for dielectric characterization of solids and liquids, and for the measurement of variables related to changes in the dielectric constant of the MUT (defect detection, material composition, etc.

Phase-variation microwave sensor for permittivity measurements based on a high-impedance half-wavelength transmission line

A phase-variation microwave sensor operating in transmission and implemented by means of a high-impedance half-wavelength sensing line is reported in this paper. The sensor is useful for dielectric constant measurements and dielectric characterization of materials. By forcing the electrical length of the sensing line to be a half-wavelength when it is loaded with the so-called reference (REF) material, perfect matching is obtained regardless of the characteristic impedance of the line. This fact can be used to enhance the sensitivity for small perturbations, by merely increasing the characteristic impedance of the sensing line. An exhaustive analysis that supports such conclusion is reported in the paper. Then, two prototype sensors are designed and fabricated for validation purposes. As compared to the ordinary phase-variation permittivity sensor implemented by means of a matched ( 50-Ω) line with identical length, the sensitivity for small perturbations in the proposed sensor is 2.1 times larger. Further advantages of these sensors are low-cost, small size, implementation in planar technology, and very simple design and fabrication, derived from the fact that the sensing region is a half-wavelength transmission lin

Differential-mode to common-mode conversion detector based on rat-race hybrid couplers : analysis and application to differential sensors and comparators

Altres ajuts: M. Gil acknowledges the Universidad Politécnica de Madrid Young Researchers Support Program (VJIDOCUPM18MGB) for its suppor

Highly-Sensitive Microwave Sensors Based on Open Complementary Split Ring Resonators (OCSRRs) for Dielectric Characterization and Solute Concentration Measurement in Liquids

International audienceDifferential permittivity sensors based on a pair of uncoupled microstrip lines, each one loaded with an open complementary split ring resonator (OCSRR), are proposed in this paper. The sensing principle is based on the measurement of the cross-mode insertion loss, very sensitive to asymmetric loading. Thus, by loading one of the OCSRRs with the reference sample, and the other one with the sample under test (SUT), the difference in the complex permittivity between both samples generates an asymmetry that gives rise to mode conversion. From the measurement of the cross-mode transmission coefficient, the dielectric properties of the SUT can be determined, provided those of the reference sample are well known. It is shown that by adding fluidic channels on top of the OCSRRs, the proposed sensor is useful for the measurement of the complex dielectric constant of liquids, and experimental results in mixtures of ethanol and deionized (DI) water and methanol in DI water, as a function of the ethanol/methanol content, are provided. Due to the high sensitivity of the proposed differential sensor to detect small perturbations (asymmetries), the structure is also of interest for the accurate measurement of solute concentrations in liquid solutions. In this paper, the structure is applied to monitor sodium content in aqueous solutions, and it is found that sodium concentrations as small as 0.25 g/L can be resolved

Highly-sensitive microwave sensors based on open complementary split ring resonators (OCSRRs) for dielectric characterization and solute concentration measurement in liquids

Differential permittivity sensors based on a pair of uncoupled microstrip lines, each one loaded with an open complementary split ring resonator (OCSRR), are proposed in this paper. The sensing principle is based on the measurement of the cross-mode insertion loss, very sensitive to asymmetric loading. Thus, by loading one of the OCSRRs with the reference sample, and the other one with the sample under test (SUT), the difference in the complex permittivity between both samples generates an asymmetry that gives rise to mode conversion. From the measurement of the cross-mode transmission coefficient, the dielectric properties of the SUT can be determined, provided those of the reference sample are well known. It is shown that by adding fluidic channels on top of the OCSRRs, the proposed sensor is useful for the measurement of the complex dielectric constant of liquids, and experimental results in mixtures of ethanol and deionized (DI) water and methanol in DI water, as a function of the ethanol/methanol content, are provided. Due to the high sensitivity of the proposed differential sensor to detect small perturbations (asymmetries), the structure is also of interest for the accurate measurement of solute concentrations in liquid solutions. In this paper, the structure is applied to monitor sodium content in aqueous solutions, and it is found that sodium concentrations as small as 0.25 g/L can be resolved

Planar microwave resonant sensors : a review and recent developments

Microwave sensors based on electrically small planar resonant elements are reviewed in this paper. By virtue of the high sensitivity of such resonators to the properties of their surrounding medium, particularly the dielectric constant and the loss factor, these sensors are of special interest (although not exclusive) for dielectric characterization of solids and liquids, and for the measurement of material composition. Several sensing strategies are presented, with special emphasis on differential-mode sensors. The main advantages and limitations of such techniques are discussed, and several prototype examples are reported, mainly including sensors for measuring the dielectric properties of solids, and sensors based on microfluidics (useful for liquid characterization and liquid composition). The proposed sensors have high potential for application in real scenarios (including industrial processes and characterization of biosamples)