Low-Power, High-Speed Transceivers for Network-on-Chip Communication

Networks on chips (NoCs) are becoming popular as they provide a solution for the interconnection problems on large integrated circuits (ICs). But even in a NoC, link-power can become unacceptably high and data rates are limited when conventional data transceivers are used. In this paper, we present a low-power, high-speed source-synchronous link transceiver which enables a factor 3.3 reduction in link power together with an 80% increase in data-rate. A low-swing capacitive pre-emphasis transmitter in combination with a double-tail sense-amplifier enable speeds in excess of 9 Gb/s over a 2 mm twisted differential interconnect, while consuming only 130 fJ/transition without the need for an additional supply. Multiple transceivers can be connected back-to-back to create a source-synchronous transceiver-chain with a wave-pipelined clock, operating with 6sigma offset reliability at 5 Gb/s

Energy-efficiency improvements for optical access

This article discusses novel approaches to improve energy efficiency of different optical access technologies, including time division multiplexing passive optical network (TDM-PON), time and wavelength division multiplexing PON (TWDM-PON), point-to-point (PTP) access network, wavelength division multiplexing PON (WDM-PON), and orthogonal frequency division multiple access PON (OFDMA-PON). These approaches include cyclic sleep mode, energy-efficient bit interleaving protocol, power reduction at component level, or frequency band selection. Depending on the target optical access technology, one or a combination of different approaches can be applied

Design of Power-Efficient Optical Transceivers and Design of High-Linearity Wireless Wideband Receivers

The combination of silicon photonics and advanced heterogeneous integration is promising for next-generation disaggregated data centers that demand large scale, high throughput, and low power. In this dissertation, we discuss the design and theory of power-efficient optical transceivers with System-in-Package (SiP) 2.5D integration. Combining prior arts and proposed circuit techniques, a receiver chip and a transmitter chip including two 10 Gb/s data channels and one 2.5 GHz clocking channel are designed and implemented in 28 nm CMOS technology. An innovative transimpedance amplifier (TIA) and a single-ended to differential (S2D) converter are proposed and analyzed for a low-voltage high-sensitivity receiver; a four-to-one serializer, programmable output drivers, AC coupling units, and custom pads are implemented in a low-power transmitter; an improved quadrature locked loop (QLL) is employed to generate accurate quadrature clocks. In addition, we present an analysis for inverter-based shunt-feedback TIA to explicitly depict the trade-off among sensitivity, data rate, and power consumption. At last, the research on CDR-based​ clocking schemes for optical links is also discussed. We introduce prior arts and propose a power-efficient clocking scheme based on an injection-locked phase rotator. Next, we analyze injection-locked ring oscillators (ILROs) that have been widely used for quadrature clock generators (QCGs) in multi-lane optical or wireline transceivers due to their low power, low area, and technology scalability. The asymmetrical or partial injection locking from 2 phases to 4 phases results in imbalances in amplitude and phase. We propose a modified frequency-domain analysis to provide intuitive insight into the performance design trade-offs. The analysis is validated by comparing analytical predictions with simulations for an ILRO-based QCG in 28 nm CMOS technology. This dissertation also discusses the design of high-linearity wireless wideband receivers. An out-of-band (OB) IM3 cancellation technique is proposed and analyzed. By exploiting a baseband auxiliary path (AP) with a high-pass feature, the in-band (IB) desired signal and out-of-band interferers are split. OB third-order intermodulation products (IM3) are reconstructed in the AP and cancelled in the baseband (BB). A 0.5-2.5 GHz frequency-translational noise-cancelling (FTNC) receiver is implemented in 65nm CMOS to demonstrate the proposed approach. It consumes 36 mW without cancellation at 1 GHz LO frequency and 1.2 V supply, and it achieves 8.8 MHz baseband bandwidth, 40dB gain, 3.3dB NF, 5dBm OB IIP3, and −6.5dBm OB B1dB. After IM3 cancellation, the effective OB-IIP3 increases to 32.5 dBm with an extra 34 mW for narrow-band interferers (two tones). For wideband interferers, 18.8 dB cancellation is demonstrated over 10 MHz with two −15 dBm modulated interferers. The local oscillator (LO) leakage is −92 dBm and −88 dB at 1 GHz and 2 GHz LO respectively. In summary, this technique achieves both high OB linearity and good LO isolation

Adaptive code division multiple access protocol for wireless network-on-chip architectures

Massive levels of integration following Moore\u27s Law ushered in a paradigm shift in the way on-chip interconnections were designed. With higher and higher number of cores on the same die traditional bus based interconnections are no longer a scalable communication infrastructure. On-chip networks were proposed enabled a scalable plug-and-play mechanism for interconnecting hundreds of cores on the same chip. Wired interconnects between the cores in a traditional Network-on-Chip (NoC) system, becomes a bottleneck with increase in the number of cores thereby increasing the latency and energy to transmit signals over them. Hence, there has been many alternative emerging interconnect technologies proposed, namely, 3D, photonic and multi-band RF interconnects. Although they provide better connectivity, higher speed and higher bandwidth compared to wired interconnects; they also face challenges with heat dissipation and manufacturing difficulties. On-chip wireless interconnects is one other alternative proposed which doesn\u27t need physical interconnection layout as data travels over the wireless medium. They are integrated into a hybrid NOC architecture consisting of both wired and wireless links, which provides higher bandwidth, lower latency, lesser area overhead and reduced energy dissipation in communication. However, as the bandwidth of the wireless channels is limited, an efficient media access control (MAC) scheme is required to enhance the utilization of the available bandwidth. This thesis proposes using a multiple access mechanism such as Code Division Multiple Access (CDMA) to enable multiple transmitter-receiver pairs to send data over the wireless channel simultaneously. It will be shown that such a hybrid wireless NoC with an efficient CDMA based MAC protocol can significantly increase the performance of the system while lowering the energy dissipation in data transfer. In this work it is shown that the wireless NoC with the proposed CDMA based MAC protocol outperformed the wired counterparts and several other wireless architectures proposed in literature in terms of bandwidth and packet energy dissipation. Significant gains were observed in packet energy dissipation and bandwidth even with scaling the system to higher number of cores. Non-uniform traffic simulations showed that the proposed CDMA-WiNoC was consistent in bandwidth across all traffic patterns. It is also shown that the CDMA based MAC scheme does not introduce additional reliability concerns in data transfer over the on-chip wireless interconnects

Energy-efficient wireline transceivers

Power-efficient wireline transceivers are highly demanded by many applications in high performance computation and communication systems. Apart from transferring a wide range of data rates to satisfy the interconnect bandwidth requirement, the transceivers have very tight power budget and are expected to be fully integrated. This thesis explores enabling techniques to implement such transceivers in both circuit and system levels. Specifically, three prototypes will be presented: (1) a 5Gb/s reference-less clock and data recovery circuit (CDR) using phase-rotating phase-locked loop (PRPLL) to conduct phase control so as to break several fundamental trade-offs in conventional receivers; (2) a 4-10.5Gb/s continuous-rate CDR with novel frequency acquisition scheme based on bang-bang phase detector (BBPD) and a ring oscillator-based fractional-N PLL as the low noise wide range DCO in the CDR loop; (3) a source-synchronous energy-proportional link with dynamic voltage and frequency scaling (DVFS) and rapid on/off (ROO) techniques to cut the link power wastage at system level. The receiver/transceiver architectures are highly digital and address the requirements of new receiver architecture development, wide operating range, and low power/area consumption while being fully integrated. Experimental results obtained from the prototypes attest the effectiveness of the proposed techniques

Editorial: clock/frequency generation circuits and systems

1 Institute of Microelectronics, Tsinghua University, Beijing 100084, China 2Department of Electronics, University of Pavia, 27100 Pavia, Italy 3Department of Electrical Engineering, Pohang University of Science and Technology, Kyungbuk 790-784, Republic of Korea 4Department of Physical Engineering, Tokyo Institute of Technology, Tokyo 152-8552, Japan 5Electrical Engineering Department, University of California, Los Angeles, CA 90095, US

A 40-Gb/s Quarter-Rate SerDes Transmitter and Receiver Chipset in 65-nm CMOS

This paper presents a 40-Gb/s transmitter (TX) and receiver (RX) chipset for chip-to-chip communications in a 65-nm CMOS process. The TX implements a quarter-rate multi-multiplexer (MUX)-based four-tap feed-forward equalizer (FFE), where a charge-sharing-effect elimination technique is introduced into the 4:1 MUX to optimize its jitter performance and power efficiency. The RX employs a two-stage continuous-time linear equalizer as the analog front end and integrates a low-cost sign-based zero-forcing engine relying on edge-data correlation to automatically adjust the tap weights of the TX-FFE. By embedding low-pass filters with an adaptively adjusting bandwidth into the data-sampling path and adopting high-linearity compensating phase interpolators, the clock data recovery achieves both high jitter tolerance and low jitter generation. The fabricated TX and RX chipset delivers 40-Gb/s PRBS data at BER 16-dB loss at half-baud frequency, while consuming a total power of 370 mW

High Speed Reconfigurable NRZ/PAM4 Transceiver Design Techniques

While the majority of wireline standards use simple binary non-return-to-zero (NRZ) signaling, four-level pulse-amplitude modulation (PAM4) standards are emerging to increase bandwidth density. This dissertation proposes efficient implementations for high speed NRZ/PAM4 transceivers. The first prototype includes a dual-mode NRZ/PAM4 serial I/O transmitter which can support both modulations with minimum power and hardware overhead. A source-series-terminated (SST) transmitter achieves 1.2Vpp output swing and employs lookup table (LUT) control of a 31-segment output digital-to-analog converter (DAC) to implement 4/2-tap feed-forward equalization (FFE) in NRZ/PAM4 modes, respectively. Transmitter power is improved with low-overhead analog impedance control in the DAC cells and a quarter-rate serializer based on a tri-state inverter-based mux with dynamic pre-driver gates. The transmitter is designed to work with a receiver that implements an NRZ/PAM4 decision feedback equalizer (DFE) that employs 1 finite impulse response (FIR) and 2 infinite impulse response (IIR) taps for first post-cursor and long-tail ISI cancellation, respectively. Fabricated in GP 65-nm CMOS, the transmitter occupies 0.060mm² area and achieves 16Gb/s NRZ and 32Gb/s PAM4 operation at 10.4 and 4.9 mW/Gb/s while operating over channels with 27.6 and 13.5dB loss at Nyquist, respectively. The second prototype presents a 56Gb/s four-level pulse amplitude modulation (PAM4) quarter-rate wireline receiver which is implemented in a 65nm CMOS process. The frontend utilize a single stage continuous time linear equalizer (CTLE) to boost the main cursor and relax the pre-cursor cancelation requirement, requiring only a 2-tap pre-cursor feed-forward equalization (FFE) on the transmitter side. A 2-tap decision feedback equalizer (DFE) with one finite impulse response (FIR) tap and one infinite impulse response (IIR) tap is employed to cancel first post-cursor and longtail inter-symbol interference (ISI). The FIR tap direct feedback is implemented inside the CML slicers to relax the critical timing of DFE and maximize the achievable data-rate. In addition to the per-slice main 3 data samplers, an error sampler is utilized for background threshold control and an edge-based sampler performs both PLL-based CDR phase detection and generates information for background DFE tap adaptation. The receiver consumes 4.63mW/Gb/s and compensates for up to 20.8dB loss when operated with a 2- tap FFE transmitter. The experimental results and comparison with state-of-the-art shows superior power efficiency of the presented prototypes for similar data-rate and channel loss. The usage of proposed design techniques are not limited to these specific prototypes and can be applied for any wireline transceiver with different modulation, data-rate and CMOS technology

Hybrid NRZ/Multi-Tone Signaling for High-Speed Low-Power Wireline Transceivers

Over the past few decades, incessant growth of Internet networking traffic and High-Performance Computing (HPC) has led to a tremendous demand for data bandwidth. Digital communication technologies combined with advanced integrated circuit scaling trends have enabled the semiconductor and microelectronic industry to dramatically scale the bandwidth of high-loss interfaces such as Ethernet, backplane, and Digital Subscriber Line (DSL). The key to achieving higher bandwidth is to employ equalization technique to compensate the channel impairments such as Inter-Symbol Interference (ISI), crosstalk, and environmental noise. Therefore, todayâs advanced input/outputs (I/Os) has been equipped with sophisticated equalization techniques to push beyond the uncompensated bandwidth of the system. To this end, process scaling has continually increased the data processing capability and improved the I/O performance over the last 15 years. However, since the channel bandwidth has not scaled with the same pace, the required signal processing and equalization circuitry becomes more and more complicated. Thereby, the energy efficiency improvements are largely offset by the energy needed to compensate channel impairments. In this design paradigm, re-thinking about the design strategies in order to not only satisfy the bandwidth performance, but also to improve power-performance becomes an important necessity. It is well known in communication theory that coding and signaling schemes have the potential to provide superior performance over band-limited channels. However, the choice of the optimum data communication algorithm should be considered by accounting for the circuit level power-performance trade-offs. In this thesis we have investigated the application of new algorithm and signaling schemes in wireline communications, especially for communication between microprocessors, memories, and peripherals. A new hybrid NRZ/Multi-Tone (NRZ/MT) signaling method has been developed during the course of this research. The system-level and circuit-level analysis, design, and implementation of the proposed signaling method has been performed in the frame of this work, and the silicon measurement results have proved the efficiency and the robustness of the proposed signaling methodology for wireline interfaces. In the first part of this work, a 7.5 Gb/s hybrid NRZ/MT transceiver (TRX) for multi-drop bus (MDB) memory interfaces is designed and fabricated in 40 nm CMOS technology. Reducing the complexity of the equalization circuitry on the receiver (RX) side, the proposed architecture achieves 1 pJ/bit link efficiency for a MDB channel bearing 45 dB loss at 2.5 GHz. The measurement results of the first prototype confirm that NRZ/MT serial data TRX can offer an energy-efficient solution for MDB memory interfaces. Motivated by the satisfying results of the first prototype, in the second phase of this research we have exploited the properties of multi-tone signaling, especially orthogonality among different sub-bands, to reduce the effect of crosstalk in high-dense wireline interconnects. A four-channel transceiver has been implemented in a standard CMOS 40 nm technology in order to demonstrate the performance of NRZ/MT signaling in presence of high channel loss and strong crosstalk noise. The proposed system achieves 1 pJ/bit power efficiency, while communicating over a MDB memory channel at 36 Gb/s aggregate data rate

Power-efficient high-speed interface circuit techniques

Inter- and intra-chip connections have become the new challenge to enable the scaling of computing systems, ranging from mobile devices to high-end servers. Demand for aggregate I/O bandwidth has been driven by applications including high-speed ethernet, backplane micro-servers, memory, graphics, chip-to-chip and network onchip. I/O circuitry is becoming the major power consumer in SoC processors and memories as the increasing bandwidth demands larger per-pin data rate or larger I/O pin count per component. The aggregate I/O bandwidth has approximately doubled every three to four years across a diverse range of standards in different applications. However, in order to keep pace with these standards enabled in part by process-technology scaling, we will require more than just device scaling in the near future. New energy-efficient circuit techniques must be proposed to enable the next generations of handheld and high-performance computers, given the thermal and system-power limits they start facing. ^ In this work, we are proposing circuit architectures that improve energy efficiency without decreasing speed performance for the most power hungry circuits in high speed interfaces. By the introduction of a new kind of logic operators in CMOS, called implication operators, we implemented a new family of high-speed frequency dividers/prescalers with reduced footprint and power consumption. New techniques and circuits for clock distribution, for pre-emphasis and for driver at the transmitter side of the I/O circuitry have been proposed and implemented. At the receiver side, new DFE architecture and CDR have been proposed and have been proven experimentally