A Low Noise Sub-Sampling PLL in Which Divider Noise Is Eliminated and PD-CP Noise Is not multiplied by N^2

This paper presents a 2.2-GHz low jitter sub-sampling based PLL. It uses a phase-detector/charge-pump (PD/CP)that sub-samples the VCO output with the reference clock. In contrast to what happens in a classical PLL, the PD/CP noise is not multiplied by N2 in this sub-sampling PLL, resulting in a low noise contribution from the PD/CP. Moreover, no frequency divider is needed in the locked state and hence divider noise and power can be eliminated. An added frequency locked loop guarantees correct frequency locking without degenerating jitter performance when in lock. The PLL is implemented in a standard 0.18- m CMOS process. It consumes 4.2 mA from a 1.8 V supply and occupies an active area of 0.4 X 0.45 m

Design of energy-efficient high-speed wireline transceiver

Energy efficiency has become the most important performance metric of integrated circuits used in many applications ranging from mobile devices to high-performance processors. The power problem permeates both computing and communication systems alike. Especially in the era of Big Data, continuously growing demand for higher communication bandwidth is driving the need for energy-efficient high-speed I/O serial links. However, the rate at which the energy efficiency of serial links is improving is much slower than the rate at which the required data transfer bandwidth is increasing. This dissertation explores two design approaches for energy-efficient communication systems. The first design approach maximizes the energy efficiency of a transceiver without any performance loss, and as a prototype, a source-synchronous multi-Gb/s transceiver that achieves excellent energy efficiency lower than 0.3pJ/bit is presented. To this end, the proposed transceiver employs aggressive supply voltage scaling, and multiplexed transmitter and receiver synchronized by low-rate multi-phase clocks are adopted to achieve high data rate even at a supply voltage close to the device threshold voltage. Phase spacing errors resulting from device mismatches are corrected using a self-calibration scheme. The proposed phase calibration method uses a single digital delay-locked loop (DLL) for calibrating all the phases, which makes the calibration process insensitive to the supply voltage level. Thanks to this technique, the proposed multi-Gb/s transceiver operates robustly and energy-efficiently at a very low supply voltage. Fabricated in a 65nm CMOS process, the energy efficiency and data rate of the prototype transceiver vary from 0.29pJ/bit to 0.58pJ/bit and 1Gb/s to 6Gb/s, respectively, as the supply voltage is varied from 0.45V to 0.7V. In the second approach, observing that the data traffic in a real system is bursty, a full-rate burst-mode transceiver that achieves rapid on/off operation needed for energy-proportional systems is presented. By injecting input data edges into the oscillator embedded in a classical type-II digital clock and data recovery (CDR) circuit, the proposed receiver achieves instantaneous phase-locking and input jitter filtering simultaneously. In other words, the proposed CDR combines the advantages of conventional feed-forward and feedback architectures to achieve energy-proportional operation. By controlling the number of data edges injected into the oscillator, both the jitter transfer bandwidth and the jitter tolerance corner are accurately controlled. The feedback loop also corrects for any frequency error and helps improve the CDR's immunity to oscillator frequency drift during the power-on and -off states. This also improves the CDR's tolerance to consecutive identical digits present in the input data. Fabricated in a 90nm CMOS process, the prototype receiver instantaneously locks onto the very first data edge and consumes 6.1mW at 2.2Gb/s. Owing to its short power-on time, the overall transceiver's energy efficiency varies only from 5.4pJ/bit to 10.7pJ/bit when the effective data rate is varied from 2.2Gb/s to 0.22Gb/s

저전력, 저면적 유선 송수신기 설계를 위한 회로 기술

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2016. 8. 정덕균.In this thesis, novel circuit techniques for low-power and area-efficient wireline transceiver, including a phase-locked loop (PLL) based on a two-stage ring oscillator, a scalable voltage-mode transmitter, and a forwarded-clock (FC) receiver based on a delay-locked-loop (DLL) based per-pin deskew, are proposed. At first, a two-stage ring PLL that provides a four-phase, high-speed clock for a quarter-rate TX in order to minimize power consumption is presented. Several analyses and verification techniques, ranging from the clocking architectures for a high-speed TX to oscillation failures in a two-stage ring oscillator, are addressed in this thesis. A tri-state-inverter–based frequency-divider and an AC-coupled clock-buffer are used for high-speed operations with minimal power and area overheads. The proposed PLL fabricated in the 65-nm CMOS technology occupies an active area of 0.009 mm2 with an integrated-RMS-jitter of 414 fs from 10 kHz to 100 MHz while consuming 7.6 mW from a 1.2-V supply at 10 GHz. The resulting figure-of-merit is -238.8 dB, which surpasses that of the state-of-the-art ring-PLLs by 4 dB. Secondly, a voltage-mode (VM) transmitter which offers a wide operation range of 6 to 32 Gb/s, controllable pre-emphasis equalization and output voltage swing without altering output impedance, and a power supply scalability is presented. A quarter-rate clocking architecture is employed in order to maximize the scalability and energy efficiency across the variety of operating conditions. A P-over-N VM driver is used for CMOS compatibility and wide voltage-swing range required for various I/O standards. Two supply regulators calibrate the output impedance of the VM driver across the wide swing and pre-emphasis range. A single phase-locked loop is used to provide a wide frequency range of 1.5-to-8 GHz. The prototype chip is fabricated in 65-nm CMOS technology and occupies active area of 0.48x0.36 mm2. The proposed transmitter achieves 250-to-600-mV single-ended swing and exhibits the energy efficiency of 2.10-to-2.93 pJ/bit across the data rate of 6-to-32 Gb/s. And last, this thesis describes a power and area-efficient FC receiver and includes an analysis of the jitter tolerance of the FC receiver. In the proposed design, jitter tolerance is maximized according to the analysis by employing a DLL-based de-skewing. A sample-swapping bang-bang phase-detector (SS-BBPD) eliminates the stuck locking caused by the finite delay range of the voltage-controlled delay line (VCDL), and also reduces the required delay range of the VCDL by half. The proposed FC receiver is fabricated in 65-nm CMOS technology and occupies an active area of 0.025 mm2. At a data rate of 12.5 Gb/s, the proposed FC receiver exhibits an energy efficiency of 0.36 pJ/bit, and tolerates 1.4-UIpp sinusoidal jitter of 300 MHz.Chapter 1. Introduction 1 1.1. Motivation 1 1.2. Thesis organization 5 Chapter 2. Phase-Locked Loop Based on Two-Stage Ring Oscillator 7 2.1. Overivew 7 2.2. Background and Analysis of a Two-stage Ring Oscillator 11 2.3. Circuit Implementation of The Proposed PLL 25 2.4. Measurement Results 33 Chapter 3. A Scalable Voltage-Mode Transmitter 37 3.1. Overview 37 3.2. Design Considerations on a Scalable Serial Link Transmitter 40 3.3. Circuit Implementation 46 3.4. Measurement Results 56 Chapter 4. Delay-Locked Loop Based Forwarded-Clock Receiver 62 4.1. Overview 62 4.2. Timing and Data Recovery in a Serial Link 65 4.3. DLL-Based Forwarded-Clock Receiver Characteristics 70 4.4. Circuit Implementation 79 4.5. Measurement Results 89 Chapter 5. Conclusion 94 Appendix 96 Appendix A. Design flow to optimize a high-speed ring oscillator 96 Appendix B. Reflection Issues in N-over-N Voltage-Mode Driver 99 Appendix C. Analysis on output swing and power consumption of the P-over-N voltage-mode driver 107 Appendix D. Loop Dynamics of DLL 112 Bibliography 121 Abstract 128Docto

Design of energy efficient high speed I/O interfaces

Energy efficiency has become a key performance metric for wireline high speed I/O interfaces. Consequently, design of low power I/O interfaces has garnered large interest that has mostly been focused on active power reduction techniques at peak data rate. In practice, most systems exhibit a wide range of data transfer patterns. As a result, low energy per bit operation at peak data rate does not necessarily translate to overall low energy operation. Therefore, I/O interfaces that can scale their power consumption with data rate requirement are desirable. Rapid on-off I/O interfaces have a potential to scale power with data rate requirements without severely affecting either latency or the throughput of the I/O interface. In this work, we explore circuit techniques for designing rapid on-off high speed wireline I/O interfaces and digital fractional-N PLLs. A burst-mode transmitter suitable for rapid on-off I/O interfaces is presented that achieves 6 ns turn-on time by utilizing a fast frequency settling ring oscillator in digital multiplying delay-locked loop and a rapid on-off biasing scheme for current mode output driver. Fabricated in 90 nm CMOS process, the prototype achieves 2.29 mW/Gb/s energy efficiency at peak data rate of 8 Gb/s. A 125X (8 Gb/s to 64 Mb/s) change in effective data rate results in 67X (18.29 mW to 0.27 mW) change in transmitter power consumption corresponding to only 2X (2.29 mW/Gb/s to 4.24 mW/Gb/s) degradation in energy efficiency for 32-byte long data bursts. We also present an analytical bit error rate (BER) computation technique for this transmitter under rapid on-off operation, which uses MDLL settling measurement data in conjunction with always-on transmitter measurements. This technique indicates that the BER bathtub width for 10^(−12) BER is 0.65 UI and 0.72 UI during rapid on-off operation and always-on operation, respectively. Next, a pulse response estimation-based technique is proposed enabling burst-mode operation for baud-rate sampling receivers that operate over high loss channels. Such receivers typically employ discrete time equalization to combat inter-symbol interference. Implementation details are provided for a receiver chip, fabricated in 65nm CMOS technology, that demonstrates efficacy of the proposed technique. A low complexity pulse response estimation technique is also presented for low power receivers that do not employ discrete time equalizers. We also present techniques for implementation of highly digital fractional-N PLL employing a phase interpolator based fractional divider to improve the quantization noise shaping properties of a 1-bit ∆Σ frequency-to-digital converter. Fabricated in 65nm CMOS process, the prototype calibration-free fractional-N Type-II PLL employs the proposed frequency-to-digital converter in place of a high resolution time-to-digital converter and achieves 848 fs rms integrated jitter (1 kHz-30 MHz) and -101 dBc/Hz in-band phase noise while generating 5.054 GHz output from 31.25 MHz input

통계적 주파수 검출기 기반 기준 주파수를 사용하지 않는 클록 및 데이터 복원 회로의 설계 방법론

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022. 8. 정덕균.In this thesis, a design of a high-speed, power-efficient, wide-range clock and data recovery (CDR) without a reference clock is proposed. A frequency acquisition scheme using a stochastic frequency detector (SFD) based on the Alexander phase detector (PD) is utilized for the referenceless operation. Pat-tern histogram analysis is presented to analyze the frequency acquisition behavior of the SFD and verified by simulation. Based on the information obtained by pattern histogram analysis, SFD using autocovariance is proposed. With a direct-proportional path and a digital integral path, the proposed referenceless CDR achieves frequency lock at all measurable conditions, and the measured frequency acquisition time is within 7μs. The prototype chip has been fabricated in a 40-nm CMOS process and occupies an active area of 0.032 mm2. The proposed referenceless CDR achieves the BER of less than 10-12 at 32 Gb/s and exhibits an energy efficiency of 1.15 pJ/b at 32 Gb/s with a 1.0 V supply.본 논문은 기준 클럭이 없는 고속, 저전력, 광대역으로 동작하는 클럭 및 데이터 복원회로의 설계를 제안한다. 기준 클럭이 없는 동작을 위해서 알렉산더 위상 검출기에 기반한 통계적 주파수 검출기를 사용하는 주파수 획득 방식이 사용된다. 통계적 주파수 검출기의 주파수 추적 양상을 분석하기 위해 패턴 히스토그램 분석 방법론을 제시하였고 시뮬레이션을 통해 검증하였다. 패턴 히스토그램 분석을 통해 얻은 정보를 바탕으로 자기공분산을 이용한 통계적 주파수 검출기를 제안한다. 직접 비례 경로와 디지털 적분 경로를 통해 제안된 기준 클럭이 없는 클럭 및 데이터 복원회로는 모든 측정 가능한 조건에서 주파수 잠금을 달성하는 데 성공하였고, 모든 경우에서 측정된 주파수 추적 시간은 7μs 이내이다. 40-nm CMOS 공정을 이용하여 만들어진 칩은 0.032 mm2의 면적을 차지한다. 제안하는 클럭 및 데이터 복원회로는 32 Gb/s의 속도에서 비트에러율 10-12 이하로 동작하였고, 에너지 효율은 32Gb/s의 속도에서 1.0V 공급전압을 사용하여 1.15 pJ/b을 달성하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 13 CHAPTER 2 BACKGROUNDS 14 2.1 CLOCKING ARCHITECTURES IN SERIAL LINK INTERFACE 14 2.2 GENERAL CONSIDERATIONS FOR CLOCK AND DATA RECOVERY 24 2.2.1 OVERVIEW 24 2.2.2 JITTER 26 2.2.3 CDR JITTER CHARACTERISTICS 33 2.3 CDR ARCHITECTURES 39 2.3.1 PLL-BASED CDR – WITH EXTERNAL REFERENCE CLOCK 39 2.3.2 DLL/PI-BASED CDR 44 2.3.3 PLL-BASED CDR – WITHOUT EXTERNAL REFERENCE CLOCK 47 2.4 FREQUENCY ACQUISITION SCHEME 50 2.4.1 TYPICAL FREQUENCY DETECTORS 50 2.4.1.1 DIGITAL QUADRICORRELATOR FREQUENCY DETECTOR 50 2.4.1.2 ROTATIONAL FREQUENCY DETECTOR 54 2.4.2 PRIOR WORKS 56 CHAPTER 3 DESIGN OF THE REFERENCELESS CDR USING SFD 58 3.1 OVERVIEW 58 3.2 PROPOSED FREQUENCY DETECTOR 62 3.2.1 MOTIVATION 62 3.2.2 PATTERN HISTOGRAM ANALYSIS 68 3.2.3 INTRODUCTION OF AUTOCOVARIANCE TO STOCHASTIC FREQUENCY DETECTOR 75 3.3 CIRCUIT IMPLEMENTATION 83 3.3.1 IMPLEMENTATION OF THE PROPOSED REFERENCELESS CDR 83 3.3.2 CONTINUOUS-TIME LINEAR EQUALIZER (CTLE) 85 3.3.3 DIGITALLY-CONTROLLED OSCILLATOR (DCO) 87 3.4 MEASUREMENT RESULTS 89 CHAPTER 4 CONCLUSION 99 APPENDIX A DETAILED FREQUENCY ACQUISITION WAVEFORMS OF THE PROPOSED SFD 100 BIBLIOGRAPHY 108 초 록 122박

Digital enhancement techniques for fractional-N frequency synthesizers

Meeting the demand for unprecedented connectivity in the era of internet-of-things (IoT) requires extremely energy efficient operation of IoT nodes to extend battery life. Managing the data traffic generated by trillions of such nodes also puts severe energy constraints on the data centers. Clock generators that are essential elements in these systems consume significant power and therefore must be optimized for low power and high performance. The focus of this thesis is on improving the energy efficiency of frequency synthesizers and clocking modules by exploring design techniques at both the architectural and circuit levels. In the first part of this work, a digital fractional-N phase locked loop (FNPLL) that employs a high resolution time-to-digital converter (TDC) and a truly ΔΣ fractional divider to achieve low in-band noise with a wide bandwidth is presented. The fractional divider employs a digital-to-time converter (DTC) to cancel out ΔΣ quantization noise in time domain, thus alleviating TDC dynamic range requirements. The proposed digital architecture adopts a narrow range low-power time-amplifier based TDC (TA-TDC) to achieve sub 1ps resolution. Fabricated in 65nm CMOS process, the prototype PLL achieves better than -106dBc/Hz in-band noise and 3MHz PLL bandwidth at 4.5GHz output frequency using 50MHz reference. The PLL achieves excellent jitter performance of 490fsrms, while consumes only 3.7mW. This translates to the best reported jitter-power figure-of-merit (FoM) of -240.5dB among previously reported FNPLLs. Phase noise performance of ring oscillator based digital FNPLLs is severely compromised by conflicting bandwidth requirements to simultaneously suppress oscillator phase and quantization noise introduced by the TDC, ΔΣ fractional divider, and digital-to-analog converter (DAC). As a consequence, their FoM that quantifies the power-jitter tradeoff is at least 25dB worse than their LC-oscillator based FNPLL counterparts. In the second part of this thesis, we seek to close this performance gap by extending PLL bandwidth using quantization noise cancellation techniques and by employing a dual-path digital loop filter to suppress the detrimental impact of DAC quantization noise. A prototype was implemented in a 65nm CMOS process operating over a wide frequency range of 2.0GHz-5.5GHz using a modified extended range multi-modulus divider with seamless switching. The proposed digital FNPLL achieves 1.9psrms integrated jitter while consuming only 4mW at 5GHz output. The measured in-band phase noise is better than -96 dBc/Hz at 1MHz offset. The proposed FNPLL achieves wide bandwidth up to 6MHz using a 50 MHz reference and its FoM is -228.5dB, which is at about 20dB better than previously reported ring-based digital FNPLLs. In the third part, we propose a new multi-output clock generator architecture using open loop fractional dividers for system-on-chip (SoC) platforms. Modern multi-core processors use per core clocking, where each core runs at its own speed. The core frequency can be changed dynamically to optimize for performance or power dissipation using a dynamic frequency scaling (DFS) technique. Fast frequency switching is highly desirable as long as it does not interrupt code execution; therefore it requires smooth frequency transitions with no undershoots. The second main requirement in processor clocking is the capability of spread spectrum frequency modulation. By spreading the clock energy across a wide bandwidth, the electromagnetic interference (EMI) is dramatically reduced. A conventional PLL clock generation approach suffers from a slow frequency settling and limited spread spectrum modulation capabilities. The proposed open loop fractional divider architecture overcomes the bandwidth limitation in fractional-N PLLs. The fractional divider switches the output frequency instantaneously and provides an excellent spread spectrum performance, where precise and programmable modulation depth and frequency can be applied to satisfy different EMI requirements. The fractional divider has unlimited modulation bandwidth resulting in spread spectrum modulation with no filtering, unlike fractional-N PLL; consequently it achieves higher EMI reduction. A prototype fractional divider was implemented in a 65nm CMOS process, where the measured peak-to-peak jitter is less than 27ps over a wide frequency range from 20MHz to 1GHz. The total power consumption is about 3.2mW for 1GHz output frequency. The all-digital implementation of the divider occupies the smallest area of 0.017mm2 compared to state-of-the-art designs. As the data rate of serial links goes higher, the jitter requirements of the clock generator become more stringent. Improving the jitter performance of conventional PLLs to less than (200fsrms) always comes with a large power penalty (tens of mWs). This is due to the PLL coupled noise bandwidth trade-off, which imposes stringent noise requirements on the oscillator and/or loop components. Alternatively, an injection-locked clock multiplier (ILCM) provides many advantages in terms of phase noise, power, and area compared to classical PLLs, but they suffer from a narrow lock-in range and a high sensitivity to PVT variations especially at a large multiplication factor (N). In the fourth part of this thesis, a low-jitter, low-power LC-based ILCM with a digital frequency-tracking loop (FTL) is presented. The proposed FTL relies on a new pulse gating technique to continuously tune the oscillator's free-running frequency. The FTL ensures robust operation across PVT variations and resolves the race condition existing in injection locked PLLs by decoupling frequency tuning from the injection path. As a result, the phase locking condition is only determined by the injection path. This work also introduces an accurate theoretical large-signal analysis for phase domain response (PDR) of injection locked oscillators (ILOs). The proposed PDR analysis captures the asymmetric nature of ILO's lock-in range, and the impact of frequency error on injection strength and phase noise performance. The proposed architecture and analysis are demonstrated by a prototype fabricated in 65 nm CMOS process with active area of 0.25mm2. The prototype ILCM multiplies the reference frequency by 64 to generate an output clock in the range of 6.75GHz-8.25GHz. A superior jitter performance of 190fsrms is achieved, while consuming only 2.25mW power. This translates to a best FoM of -251dB. Unlike conventional PLLs, ILCMs have been fundamentally limited to only integer-N operation and cannot synthesize fractional-N frequencies. In the last part of this thesis, we extend the merits of ILCMs to fractional-N and overcome this fundamental limitation. We employ DTC-based QNC techniques in order to align injected pulses to the oscillator's zero crossings, which enables it to pull the oscillator toward phase lock, thus realizing a fractional-N ILCM. Fabricated in 65nm CMOS process, a prototype 20-bit fractional-N ILCM with an output range of 6.75GHz-8.25GHz consumes only 3.25mW. It achieves excellent jitter performance of 110fsrms and 175fsrms in integer- and fractional-N modes respectively, which translates to the best-reported FoM in both integer- (-255dB) and fractional-N (-252dB) modes. The proposed fractional-N ILCM also features the first-reported rapid on/off capability, where the transient absolute jitter performance at wake-up is bounded below 4ps after less than 4ns. This demonstrates almost instantaneous phase settling. This unique capability enables tremendous energy saving by turning on the clock multiplier only when needed. This energy proportional operation leverages idle times to save power at the system-level of wireline and wireless transceivers

Clock multiplication techniques for high-speed I/Os

Generation of a low-jitter, high-frequency clock from a low-frequency reference clock using classical analog phase-locked loops (PLLs) requires a large loop filter capacitor and power hungry oscillator. Digital PLLs can help reduce area but their jitter performance is severely degraded by quantization error. In this dissertation different clock multiplication techniques have been explored that can be suitable for high-speed wireline systems. With the emphasis on ring oscillator based architecture using cascaded stages, three possible architectures are explored. First, a scrambling TDC (STDC) is presented to improve deterministic jitter (DJ) performance when used with a low-frequency reference clock. A cascaded architecture with digital multiplying delay locked loop as the first stage and hybrid analog/digital PLL as the second stage is used to achieve low random jitter in a power efficient manner. Fabricated in a 90nm CMOS process, the prototype frequency synthesizer consumes 4.76mW power from a 1.0V supply and generates 160MHz and 2.56 GHz output clocks from a 1.25MHz crystal reference frequency. The long-term absolute jitter of the 60MHz digital MDLL and 2.56 GHz digital PLL outputs are 2.4 psrms and 4.18 psrms, while the peak-to-peak jitter is 22.1 ps and 35.2 ps, respectively. The proposed frequency synthesizer occupies an active die area of 0.16mm2 and achieves power efficiency of 1.86 mW/GHz. Second, a hybrid phase/current-mode phase interpolator (HPC-PI) is presented to improve phase noise performance of ring oscillator-based fractional-N PLLs. The proposed HPC-PI alleviates the bandwidth trade-off between VCO phase noise suppression and ΔΣ quantization noise suppression. By combining the phase detection and interpolation functions into an XOR phase detector/interpolator (XOR PD-PI) block, accurate quantization error cancellation is achieved without using calibration. Use of a digital MDLL in front of the fractional-N PLL helps in alleviating the bandwidth limitation due to reference frequency and enables bandwidth extension even further. The extended bandwidth helps in suppressing the ring-VCO phase noise and lowering the in-band noise floor. Fabricated in 65nm CMOS process, the prototype generates fractional frequencies from 4.25 to 4.75 GHz, with an in-band phase noise floor of -104 dBc/Hz and 1.5 psrms integrated jitter. The clock multiplier achieves power efficiency of 2.4mW/GHz and FoM of -225.8 dB. Finally, an efficient clock generation, recovery, and distribution techniques for flexible-rate transceivers are presented. Using a fixed-frequency low-jitter clock provided by an integer-N PLL, fractional frequencies are generated/recovered locally using multi-phase fractional clock multipliers. Fabricated in a 65nm CMOS, the prototype transceiver can be programmed to operate at any rate from 3-to-10 Gb/s. At 10 Gb/s, integrated jitter of the Tx output and recovered clock is 360 fsrms and 758 fsrms, respectively

Design of all digital phase-locked loop in serial link communication

The speed of wireline and wireless communication systems has been increasing aggressively over the past decade. Multi-GHz clocks are in demand more than ever. In particular, wireline inter-IC communications systems such as broadband Internet, multi-core CPU and system-on-chip have fueled the research on faster on-chip clock synthesizers. In addition, mobile products such as cell-phones and tablets have permeated the consumer market. Since these devices are battery-powered, it is necessary to minimize the battery consumption of the communication system circuitry inside to extend the battery life. As a result, low-power inter-IC communication design is another topic that is gaining interest. In high speed links, clocking circuitry is vital, and phase-locked loop (PLL) is at the heart of every on-chip clocking circuit. The clocking circuitry needs to be robust, low-power and fast in order to fulfill the increasing demand for high data rate links. The performance of the input/output (I/O) communication channel needs to scale proportionally with the semiconductor fabrication technology (SFT). However, conventional analog PLLs are often incompatible from one technology node to the next and require entirely new designs. In recent years, with the increased performance of digital circuits, all digital PLL (ADPLL) has achieved speed performance similar to that of analog PLL. Since digital logic is more robust, portable, and power efficient, ADPLL is gaining traction in research. This thesis presents the fundamentals and an in-depth analysis of the conventional analog PLL in Chapters 2 and 3. Then the discussion dives into ADPLL. Chapter 4 presents the building blocks and loop analysis of the ADPLL. Chapter 5 presents jitter sources and jitter analysis inside the ADPLL. Chapter 6 presents an ADPLL in model and transistor design. It has center frequency of 1.6GHz and operates from 1.2GHz to 2.0GHz. Chapter 7 concludes the thesis and discusses future work

Clock/Frequency Generation Circuits and Systems

1 Institute of Microelectronics, Tsinghua University, Beijing 100084, China 2Department of Electronics, University of Pavia, 27100 Pavia, Italy 3Department of Electrical Engineering, Pohang University of Science and Technology, Kyungbuk 790-784, Republic of Korea 4Department of Physical Engineering, Tokyo Institute of Technology, Tokyo 152-8552, Japan 5Electrical Engineering Department, University of California, Los Angeles, CA 90095, US

DESIGN AND CHARACTERIZATION OF LOW-POWER LOW-NOISE ALLDIGITAL SERIAL LINK FOR POINT-TO-POINT COMMUNICATION IN SOC

The fully-digital implementation of serial links has recently emerged as a viable alternative to their classical analogue counterpart. Indeed, reducing the analogue content in favour of expanding the digital content becomes more attractive due to the ability to achieve less power consumption, less sensitivity to the noise and better scalability across multiple technologies and platforms with inconsiderable modifications. In addition, describing the circuit in hardware description languages gives it a high flexibility to program all design parameters in a very short time compared with the analogue designs which need to be re-designed at transistor level for any parameter change. This can radically reduce cost and time-to-market by saving a significant amount of development time. However, beside these considerable advantages, the fully-digital architecture poses several design challenges