Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Multi-standard programmable baseband modulator for next generation wireless communication

Considerable research has taken place in recent times in the area of parameterization of software defined radio (SDR) architecture. Parameterization decreases the size of the software to be downloaded and also limits the hardware reconfiguration time. The present paper is based on the design and development of a programmable baseband modulator that perform the QPSK modulation schemes and as well as its other three commonly used variants to satisfy the requirement of several established 2G and 3G wireless communication standards. The proposed design has been shown to be capable of operating at a maximum data rate of 77 Mbps on Xilinx Virtex 2-Pro University field programmable gate array (FPGA) board. The pulse shaping root raised cosine (RRC) filter has been implemented using distributed arithmetic (DA) technique in the present work in order to reduce the computational complexity, and to achieve appropriate power reduction and enhanced throughput. The designed multiplier-less programmable 32-tap FIR-based RRC filter has been found to withstand a peak inter-symbol interference (ISI) distortion of -41 dB

Partially reconfigurable TVWS transceiver for use in UK and US markets

With more and more countries opening up sections of unlicensed spectrum for use by TV White Space (TVWS) devices, the prospect of building a device capable of operating in more than one world region is appealing. The difficulty is that the locations of TVWS bands within the radio spectrum are not globally harmonised. With this problem in mind, the purpose of this paper is to present a TVWS transceiver design which is capable of being reconfigured to operate in both the UK and US spectrum. We present three different configurations: one covering the UK TVWS spectrum and the remaining two covering the various locations of the US TVWS bands

Hardware/Software Co-design Applied to Reed-Solomon Decoding for the DMB Standard

This paper addresses the implementation of Reed- Solomon decoding for battery-powered wireless devices. The scope of this paper is constrained by the Digital Media Broadcasting (DMB). The most critical element of the Reed-Solomon algorithm is implemented on two different reconfigurable hardware architectures: an FPGA and a coarse-grained architecture: the Montium, The remaining parts are executed on an ARM processor. The results of this research show that a co-design of the ARM together with an FPGA or a Montium leads to a substantial decrease in energy consumption. The energy consumption of syndrome calculation of the Reed- Solomon decoding algorithm is estimated for an FPGA and a Montium by means of simulations. The Montium proves to be more efficient

Design exploration and performance strategies towards power-efficient FPGA-based achitectures for sound source localization

Many applications rely on MEMS microphone arrays for locating sound sources prior to their execution. Those applications not only are executed under real-time constraints but also are often embedded on low-power devices. These environments become challenging when increasing the number of microphones or requiring dynamic responses. Field-Programmable Gate Arrays (FPGAs) are usually chosen due to their flexibility and computational power. This work intends to guide the design of reconfigurable acoustic beamforming architectures, which are not only able to accurately determine the sound Direction-Of-Arrival (DoA) but also capable to satisfy the most demanding applications in terms of power efficiency. Design considerations of the required operations performing the sound location are discussed and analysed in order to facilitate the elaboration of reconfigurable acoustic beamforming architectures. Performance strategies are proposed and evaluated based on the characteristics of the presented architecture. This power-efficient architecture is compared to a different architecture prioritizing performance in order to reveal the unavoidable design trade-offs