Developing and Testing an Anguilliform Robot Swimming with Theoretically High Hydrodynamic Efficiency

An anguilliform swimming robot replicating an idealized motion is a complex marine vehicle necessitating both a theoretical and experimental analysis to completely understand its propulsion characteristics. The ideal anguilliform motion within is theorized to produce ``wakeless\u27\u27 swimming (Vorus, 2011), a reactive swimming technique that produces thrust by accelerations of the added mass in the vicinity of the body. The net circulation for the unsteady motion is theorized to be eliminated. The robot was designed to replicate the desired, theoretical motion by applying control theory methods. Independent joint control was used due to hardware limitations. The fluid velocity vectors in the propulsive wake downstream of the tethered, swimming robot were measured using Particle Image Velocimetry (PIV). Simultaneously, a load cell measured the thrust (or drag) forces of the robot via a hydrodynamic tether. The measured field velocities and thrust forces were compared to the theoretical predictions for each. The desired, ideal motion was not replicated consistently during PIV testing, producing off-design scenarios. The thrust-computing method for the ideal motion was applied to the actual, recorded motion and compared to the load cell results. The theoretical field velocities were computed differently by accounting for shed vortices due to a different shape than ideal. The theoretical thrust shows trends similar to the measured thrust over time. Similarly promising comparisons are found between the theoretical and measured flow-field velocities with respect to qualitative trends and velocity magnitudes. The initial thrust coefficient prediction was deemed insufficient, and a new one was determined from an iterative process. The off-design cases shed flow structures into the downstream wake of the robot. The first is a residual disturbance of the shed boundary layer, which is to be expected for the ideal case, and dissipates within one motion cycle. The second are larger-order vortices that are being shed at two distinct times during a half-cycle. These qualitative and quantitative comparisons were used to confirm the possibility of the original hypothesis of ``wakeless\u27\u27 swimming. While the ideal motion could not be tested consistently, the results of the off-design cases agree significantly with the adjusted theoretical computations. This shows that the boundary conditions derived from slender-body constraints and the assumptions of ideal flow theory are sufficient enough to predict the propulsion characteristics of an anguilliform robot undergoing this specific motion

A NEUROMORPHIC APPROACH TO TACTILE PERCEPTION

Ph.DDOCTOR OF PHILOSOPH

Soft Robot-Assisted Minimally Invasive Surgery and Interventions: Advances and Outlook

Since the emergence of soft robotics around two decades ago, research interest in the field has escalated at a pace. It is fuelled by the industry's appreciation of the wide range of soft materials available that can be used to create highly dexterous robots with adaptability characteristics far beyond that which can be achieved with rigid component devices. The ability, inherent in soft robots, to compliantly adapt to the environment, has significantly sparked interest from the surgical robotics community. This article provides an in-depth overview of recent progress and outlines the remaining challenges in the development of soft robotics for minimally invasive surgery

High-Performance Integrated Window and Façade Solutions for California

The researchers developed a new generation of high-performance façade systems and supporting design and management tools to support industry in meeting California’s greenhouse gas reduction targets, reduce energy consumption, and enable an adaptable response to minimize real-time demands on the electricity grid. The project resulted in five outcomes: (1) The research team developed an R-5, 1-inch thick, triplepane, insulating glass unit with a novel low-conductance aluminum frame. This technology can help significantly reduce residential cooling and heating loads, particularly during the evening. (2) The team developed a prototype of a windowintegrated local ventilation and energy recovery device that provides clean, dry fresh air through the façade with minimal energy requirements. (3) A daylight-redirecting louver system was prototyped to redirect sunlight 15–40 feet from the window. Simulations estimated that lighting energy use could be reduced by 35–54 percent without glare. (4) A control system incorporating physics-based equations and a mathematical solver was prototyped and field tested to demonstrate feasibility. Simulations estimated that total electricity costs could be reduced by 9-28 percent on sunny summer days through adaptive control of operable shading and daylighting components and the thermostat compared to state-of-the-art automatic façade controls in commercial building perimeter zones. (5) Supporting models and tools needed by industry for technology R&D and market transformation activities were validated. Attaining California’s clean energy goals require making a fundamental shift from today’s ad-hoc assemblages of static components to turnkey, intelligent, responsive, integrated building façade systems. These systems offered significant reductions in energy use, peak demand, and operating cost in California

The computer synthesis of expressive three-dimensional facial character animation.

This present research is concerned with the design, development and implementation of three-dimensional computer-generated facial images capable of expression gesture and speech. A review of previous work in chapter one shows that to date the model of computer-generated faces has been one in which construction and animation were not separated and which therefore possessed only a limited expressive range. It is argued in chapter two that the physical description of the face cannot be seen as originating from a single generic mould. Chapter three therefore describes data acquisition techniques employed in the computer generation of free-form surfaces which are applicable to three-dimensional faces. Expressions are the result of the distortion of the surface of the skin by the complex interactions of bone, muscle and skin. Chapter four demonstrates with static images and short animation sequences in video that a muscle model process algorithm can simulate the primary characteristics of the facial muscles. Three-dimensional speech synchronization was the most complex problem to achieve effectively. Chapter five describes two successful approaches: the direct mapping of mouth shapes in two dimensions to the model in three dimensions, and geometric distortions of the mouth created by the contraction of specified muscle combinations. Chapter six describes the implementation of software for this research and argues the case for a parametric approach. Chapter seven is concerned with the control of facial articulations and discusses a more biological approach to these. Finally chapter eight draws conclusions from the present research and suggests further extensions

Aeronautical engineering: A continuing bibliography with indexes (supplement 275)

This bibliography lists 379 reports, articles, and other documents introduced into the NASA scientific and technical information system in Jan. 1991