Biomimetic Manipulator Control Design for Bimanual Tasks in the Natural Environment

As robots become more prolific in the human environment, it is important that safe operational procedures are introduced at the same time; typical robot control methods are often very stiff to maintain good positional tracking, but this makes contact (purposeful or accidental) with the robot dangerous. In addition, if robots are to work cooperatively with humans, natural interaction between agents will make tasks easier to perform with less effort and learning time. Stability of the robot is particularly important in this situation, especially as outside forces are likely to affect the manipulator when in a close working environment; for example, a user leaning on the arm, or task-related disturbance at the end-effector. Recent research has discovered the mechanisms of how humans adapt the applied force and impedance during tasks. Studies have been performed to apply this adaptation to robots, with promising results showing an improvement in tracking and effort reduction over other adaptive methods. The basic algorithm is straightforward to implement, and allows the robot to be compliant most of the time and only stiff when required by the task. This allows the robot to work in an environment close to humans, but also suggests that it could create a natural work interaction with a human. In addition, no force sensor is needed, which means the algorithm can be implemented on almost any robot. This work develops a stable control method for bimanual robot tasks, which could also be applied to robot-human interactive tasks. A dynamic model of the Baxter robot is created and verified, which is then used for controller simulations. The biomimetic control algorithm forms the basis of the controller, which is developed into a hybrid control system to improve both task-space and joint-space control when the manipulator is disturbed in the natural environment. Fuzzy systems are implemented to remove the need for repetitive and time consuming parameter tuning, and also allows the controller to actively improve performance during the task. Experimental simulations are performed, and demonstrate how the hybrid task/joint-space controller performs better than either of the component parts under the same conditions. The fuzzy tuning method is then applied to the hybrid controller, which is shown to slightly improve performance as well as automating the gain tuning process. In summary, a novel biomimetic hybrid controller is presented, with a fuzzy mechanism to avoid the gain tuning process, finalised with a demonstration of task-suitability in a bimanual-type situation.EPSR

Robotic Trajectory Tracking: Position- and Force-Control

This thesis employs a bottom-up approach to develop robust and adaptive learning algorithms for trajectory tracking: position and torque control. In a first phase, the focus is put on the following of a freeform surface in a discontinuous manner. Next to resulting switching constraints, disturbances and uncertainties, the case of unknown robot models is addressed. In a second phase, once contact has been established between surface and end effector and the freeform path is followed, a desired force is applied. In order to react to changing circumstances, the manipulator needs to show the features of an intelligent agent, i.e. it needs to learn and adapt its behaviour based on a combination of a constant interaction with its environment and preprogramed goals or preferences. The robotic manipulator mimics the human behaviour based on bio-inspired algorithms. In this way it is taken advantage of the know-how and experience of human operators as their knowledge is translated in robot skills. A selection of promising concepts is explored, developed and combined to extend the application areas of robotic manipulators from monotonous, basic tasks in stiff environments to complex constrained processes. Conventional concepts (Sliding Mode Control, PID) are combined with bio-inspired learning (BELBIC, reinforcement based learning) for robust and adaptive control. Independence of robot parameters is guaranteed through approximated robot functions using a Neural Network with online update laws and model-free algorithms. The performance of the concepts is evaluated through simulations and experiments. In complex freeform trajectory tracking applications, excellent absolute mean position errors (<0.3 rad) are achieved. Position and torque control are combined in a parallel concept with minimized absolute mean torque errors (<0.1 Nm)

AI based Robot Safe Learning and Control

Introduction This open access book mainly focuses on the safe control of robot manipulators. The control schemes are mainly developed based on dynamic neural network, which is an important theoretical branch of deep reinforcement learning. In order to enhance the safety performance of robot systems, the control strategies include adaptive tracking control for robots with model uncertainties, compliance control in uncertain environments, obstacle avoidance in dynamic workspace. The idea for this book on solving safe control of robot arms was conceived during the industrial applications and the research discussion in the laboratory. Most of the materials in this book are derived from the authors’ papers published in journals, such as IEEE Transactions on Industrial Electronics, neurocomputing, etc. This book can be used as a reference book for researcher and designer of the robotic systems and AI based controllers, and can also be used as a reference book for senior undergraduate and graduate students in colleges and universities

Proceedings of the NASA Conference on Space Telerobotics, volume 4

Papers presented at the NASA Conference on Space Telerobotics are compiled. The theme of the conference was man-machine collaboration in space. The conference provided a forum for researchers and engineers to exchange ideas on the research and development required for the application of telerobotic technology to the space systems planned for the 1990's and beyond. Volume 4 contains papers related to the following subject areas: manipulator control; telemanipulation; flight experiments (systems and simulators); sensor-based planning; robot kinematics, dynamics, and control; robot task planning and assembly; and research activities at the NASA Langley Research Center

On Sensorless Collision Detection and Measurement of External Forces in Presence of Modeling Inaccuracies

The field of human-robot interaction has garnered significant interest in the last decade. Every form of human-robot coexistence must guarantee the safety of the user. Safety in human-robot interaction is being vigorously studied, in areas such as collision avoidance, soft actuators, light-weight robots, computer vision techniques, soft tissue modeling, collision detection, etc. Despite the safety provisions, unwanted collisions can occur in case of system faults. In such cases, before post-collision strategies are triggered, it is imperative to effectively detect the collisions. Implementation of tactile sensors, vision systems, sonar and Lidar sensors, etc., allows for detection of collisions. However, due to the cost of such methods, more practical approaches are being investigated. A general goal remains to develop methods for fast detection of external contacts using minimal sensory information. Availability of position data and command torques in manipulators permits development of observer-based techniques to measure external forces/torques. The presence of disturbances and inaccuracies in the model of the robot presents challenges in the efficacy of observers in the context of collision detection. The purpose of this thesis is to develop methods that reduce the effects of modeling inaccuracies in external force/torque estimation and increase the efficacy of collision detection. It is comprised of the following four parts: 1. The KUKA Light-Weight Robot IV+ is commonly employed for research purposes. The regressor matrix, minimal inertial parameters and the friction model of this robot are identified and presented in detail. To develop the model, relative weight analysis is employed for identification. 2. Modeling inaccuracies and robot state approximation errors are considered simultaneously to develop model-based time-varying thresholds for collision detection. A metric is formulated to compare trajectories realizing the same task in terms of their collision detection and external force/torque estimation capabilities. A method for determining optimal trajectories with regards to accurate external force/torque estimation is also developed. 3. The effects of velocity on external force/torque estimation errors are studied with and without the use of joint force/torque sensors. Velocity-based thresholds are developed and implemented to improve collision detection. The results are compared with the collision detection module integrated in the KUKA Light-Weight Robot IV+. 4. An alternative joint-by-joint heuristic method is proposed to identify the effects of modeling inaccuracies on external force/torque estimation. Time-varying collision detection thresholds associated with the heuristic method are developed and compared with constant thresholds. In this work, the KUKA Light-Weight Robot IV+ is used for obtaining the experimental results. This robot is controlled via the Fast Research Interface and Visual C++ 2008. The experimental results confirm the efficacy of the proposed methodologies

Non-conventional control of the flexible pole-cart balancing problem

Emerging techniques of intelligent or learning control seem attractive for applications in manufacturing and robotics. It is however important to understand the capabilities of such control systems. In the past the inverted pendulum has been used as a test case. The thesis begins with an examination of whether the inverted pendulum or polecart balancing problem is a representative problem for experimentation for learning controllers for complex nonlinear systems. Results of previous research concerning the inverted pendulum problem are presented to show that this problem is not sufficiently testing. This thesis therefore concentrates on the control of the inverted pendulum with an additional degree of freedom as a testing demonstrator problem for learning control system experimentation. A flexible pole is used in place of a rigid one. The transverse displacement of the flexible pole adds a degree of freedom to the system. The dynamics of this new system are more complex as the system needs additional parameters to be defIned due to the pole's elastic deflection. This problem also has many of the signifIcant features associated with flexible robots with lightweight links as applied in manufacturing. Novel neural network and fuzzy control systems are presented that control such a system both in simulation and real time. A fuzzy-genetic approach is also demonstrated that allows the creation of fuzzy control systems without the use of extensive knowledge

Conference on Intelligent Robotics in Field, Factory, Service, and Space (CIRFFSS 1994), volume 1

The AIAA/NASA Conference on Intelligent Robotics in Field, Factory, Service, and Space (CIRFFSS '94) was originally proposed because of the strong belief that America's problems of global economic competitiveness and job creation and preservation can partly be solved by the use of intelligent robotics, which are also required for human space exploration missions. Individual sessions addressed nuclear industry, agile manufacturing, security/building monitoring, on-orbit applications, vision and sensing technologies, situated control and low-level control, robotic systems architecture, environmental restoration and waste management, robotic remanufacturing, and healthcare applications

Adaptive Control

Adaptive control has been a remarkable field for industrial and academic research since 1950s. Since more and more adaptive algorithms are applied in various control applications, it is becoming very important for practical implementation. As it can be confirmed from the increasing number of conferences and journals on adaptive control topics, it is certain that the adaptive control is a significant guidance for technology development.The authors the chapters in this book are professionals in their areas and their recent research results are presented in this book which will also provide new ideas for improved performance of various control application problems