Dual-band ridged waveguide

Waveguide-in-waveguide technique involves routing two waveguides through same passageway. Smaller waveguide can be soft or silver soldered inside X-band waveguide to form single ridge guide and to propagate frequencies at C-band

Dual-Band Rectifier Based on Resistance Compression Networks

This work presents the design of a dual-band rectifier operating at 915 MHz and 2.45 GHz with minimized sensitivity to input power and load variations. The rectifier is designed using a dual-band resistance compression network (RCN) for minimizing the effect of input power and load changes and it is based on Composite Right/Left-Handed (CRLH) to implement the dual band operation. The resulting rectifier has shown good RF-DC conversion efficiency and reduced sensitivity to variations

Novel Compact and High Selectivity Dual-band BPF with Wide Stopband

A novel type of compact and high selectivity dual-band bandpass filter (BPF) incorporating a dual-mode defected ground structure resonator (DDGSR) and a dual-mode open-stub loaded stepped impedance resonator (DOLSIR) is proposed in this paper. Utilizing capacitive source-load coupling and the intrinsic characteristics of the two types of dual-mode resonators, compact dual-band BPF with multi transmission zeros near the passband edges as well as a wide stopband which can be used to achieve high selectivity is realized. An experimental dual-band BPF located at 2.4 and 3.2 GHz was designed and fabricated. The validity of the design approach is verified by good agreement between simulated and measurement results

Dual-Band Tunable Recursive Active Filter

This letter presents a novel recursive active filter topology that provides dual-band performance, with independent tuning capability in both bands. The dual-band operation is achieved by using two independent feedback lines. Additionally, linear phase shifters based on left-handed cells are included in these two branches in order to tune the center frequency of both pass bands

A Dual Band Belt Antenna

This paper presents an antenna structure design using a standard belt for wearable applications. The antenna arouse from a body of research work on wearable metallic structures functioning as antennas for wireless on-body networks

A 6-to-18 GHz tunable concurrent dual-band receiver front end for scalable phased arrays in 130nm CMOS

This paper presents a study and design of tunable concurrent dual-band receiver. Different system architectures and building blocks have been compared and analyzed. A tunable concurrent dual-band receiver front end has then been fabricated and characterized. It operates across a tri-tave 6-18 GHz bandwidth with a nominal 17-25 dB conversion gain, worst-case -15 dBm IIP3, and worst-case -24.5 dBm ICP 1 dB

A reconfigurable wideband and multiband antenna using dual-patch elements for compact wireless devices

This is the post-print version of the Article. The official published version can be accessed from the link below - Copyright @ 2012 IEEEA reconfigurable wideband and multiband C-Slot patch antenna with dual-patch elements is proposed and studied. It occupies a compact volume of 50 × 50 × 1.57 (3925 mm3), including the ground plane. The antenna can operate in two dual-band modes and a wideband mode from 5 to 7 GHz. Two parallel C-Slots on the patch elements are employed to perturb the surface current paths for excitation of the dual-band and the wideband modes. Two switches, implemented using PIN diodes, are placed on the connecting lines of a simple feed network to the patch elements. Dual-band modes are achieved by switching “ON” either one of the two patch elements, while the wideband mode with an impedance bandwidth of 33.52% is obtained by switching “ON” both patch elements. The frequencies in the dual-band modes can be independently controlled using positions and dimensions of the C-Slots without affecting the wideband mode. The advantage of the proposed antenna is that two dual-band operations and one wideband operation can be achieved using the same dimensions. This overcomes the need for increasing the surface area normally incurred when designing wideband patch antennas. Simulation results are validated experimentally through prototypes. The measured radiation patterns and peak gains show stable responses and are in good agreements. Coupling between the two patch elements plays a major role for achieving the wide bandwidth and the effects of mutual coupling between the patch elements are also studied

Dual band combiner for horn antenna

A corrugated horn antenna, adapted to be coupled to a waveguide at its apex for X-band excitation is further adapted to be connected to waveguides through a circumferential slot for S-band excitation at four distinct phases selected for the desired S-band polarization. The circumferential slot is positioned along the axial length of the horn for good impedance matching and is provided with an X-band choke in the form of two concentric choke slots. For further improvement in impedance matching, the second (outer) choke slot is divided by plugs into four segments that coincide with waveguide ports for the four distinct phases of the S-band

Design of Dual-Band Two-Branch-Line Couplers with Arbitrary Coupling Coefficients in Bands

A new approach to design dual-band two-branch couplers with arbitrary coupling coefficients at two operating frequency bands is proposed in this article. The method is based on the usage of equivalent subcircuits input reactances of the even-mode and odd-mode excitations. The exact design formulas for three options of the dual-band coupler with different location and number of stubs are received. These formulas permit to obtain the different variants for each structure in order to select the physically realizable solution and can be used in broad range of frequency ratio and power division ratio. For verification, three different dual-band couplers, which are operating at 2.4/3.9 GHz with different coupling coefficients (one with 3/6 dB, and 10/3 dB two others) are designed, simulated, fabricated and tested. The measured results are in good agreement with the simulated ones

Dual band fss with fractal elements

Experimental and computed results of a frequency selective surface (FSS) based on a certain type of fractal element are presented. The fractal element is a two iteration Sierpinski gasket dipole. Owing to the dual band behaviour of the two iteration Sierpinski gasket dipole, two stopbands are exhibited within the operating frequency band. This behaviour is obtained by arraying one simple element in a single layer frequency selective surface (FSS)Peer ReviewedPostprint (published version