Gemini multi-conjugate adaptive optics system review II: Commissioning, operation and overall performance

The Gemini Multi-conjugate Adaptive Optics System - GeMS, a facility instrument mounted on the Gemini South telescope, delivers a uniform, near diffraction limited images at near infrared wavelengths (0.95 microns- 2.5 microns) over a field of view of 120 arc seconds. GeMS is the first sodium layer based multi laser guide star adaptive optics system used in astronomy. It uses five laser guide stars distributed on a 60 arc seconds square constellation to measure for atmospheric distortions and two deformable mirrors to compensate for it. In this paper, the second devoted to describe the GeMS project, we present the commissioning, overall performance and operational scheme of GeMS. Performance of each sub-system is derived from the commissioning results. The typical image quality, expressed in full with half maximum, Strehl ratios and variations over the field delivered by the system are then described. A discussion of the main contributor to performance limitation is carried-out. Finally, overheads and future system upgrades are described.Comment: 20 pages, 11 figures, accepted for publication in MNRA

Laser space rendezvous and docking system study continuation

Investigations were made of a configuration for a spaceborne laser radar (ladar) to meet the requirements for rendezvous and docking with a cooperative object in synchronous orbit. An analysis was completed of laser phase locking techniques, while experimental verification was made of pulse repetition frequency and resonant scanning control loops. Data measurements on a satellite mock-up were also made. The investigation supports the original contention that a rendezvous and docking ladar can be configured to offer a cost effective and reliable solution to envisioned space missions

A comparison of variable valve strategies at part load for throttled and un-throttled SI engine configurations

The presented work concerns the study of the fuel consumption and emissions benefits achieved at part load by employing a fully variable valve train in a 1.6L SI gasoline engine. The benefits achieved when using variable valve timing alone, and combined with an early intake closing strategy for un-throttled operation were explored in order to highlight the merits of throttle versus un-throttled engine operation in conjunction with variable valve timing and lift. In addition, particular interest was given to the presence of internal Exhaust Gas Recirculation (EGR) and its ability to reduce pumping loss at part load. An engine model employing multiple sub models to handle variable valve operation was constructed using a commercial gas dynamics engine code, allowing detailed analysis of three valve strategies. Using the engine model, a theoretical study validated by experimentally available data was carried out to study key valve timing cases. A detailed breakdown of the mechanisms present in each case allowed a comprehensive understanding of the influence of valve timing on gas exchange efficiency and fuel consumption

A 12 GHz satellite video receiver: Low noise, low cost prototype model for TV reception from broadcast satellites

A 12-channel synchronous phase lock video receiver consisting of an outdoor downconverter unit and an indoor demodulator unit was developed to provide both low noise performance and low cost in production quantities of 1000 units. The prototype receiver can be mass produced at a cost under $1540 without sacrificing system performance. The receiver also has the capability of selecting any of the twelve assigned satellite broadcast channels in the frequency range 11.7 to 12.2 GHz

Single-stage electrohydraulic servosystem for actuating on airflow valve with frequencies to 500 hertz

An airflow valve and its electrohydraulic actuation servosystem are described. The servosystem uses a high-power, single-stage servovalve to obtain a dynamic response beyond that of systems designed with conventional two-stage servovalves. The electrohydraulic servosystem is analyzed and the limitations imposed on system performance by such nonlinearities as signal saturations and power limitations are discussed. Descriptions of the mechanical design concepts and developmental considerations are included. Dynamic data, in the form of sweep-frequency test results, are presented and comparison with analytical results obtained with an analog computer model is made

A 0.2-to-2.0GHz 65nm CMOS Receiver without LNA achieving >11dBm IIP3 and <6.5 dB NF

Spurious-free dynamic range (SFDR) is a key specification of radio receivers and spectrum analyzers, characterizing the maximum distance between signal and noise+distortion. SFDR is limited by the linearity (intercept point IIP3 mostly, sometimes IIP2) and the noise floor. As receivers already have low noise figure (NF) there is more room for improving the SFDR by increasing the linearity. As there is a strong relation between distortion and voltage swing, it is challenging to maintain or even improve linearity intercept points in future CMOS processes with lower supply voltages. Circuits can be linearized with feedback but loop gain at RF is limited [1]. Moreover, after LNA gain, mixer linearity becomes even tougher. If the amplification is postponed to IF, much more loop gain is available to linearize the amplifier. This paper proposes such an LNA-less mixer-first receiver. By careful analysis and optimization of a passive mixer core [2,3] for low conversion loss and low noise folding it is shown that it is possible to realize IIP3≫11dBm and NF≪6.5dB, i.e. a remarkably high SFDR≫79dB in 1MHz bandwidth over a decade of RF frequencies

No-moving-part hybrid-synthetic jet actuator

In contrast to usual synthetic jets, the “hybrid-synthetic jets” of non-zero timemean nozzle mass flow rate are increasingly often considered for control of flow separation and/or transition to turbulence as well as heat and mass transfer. The paper describes tests of a scaled-up laboratory model of a new actuator version, generating the hybrid-synthetic jets without any moving components. Self-excited flow oscillation is produced by aerodynamic instability in fixed-wall cavities. The return flow in the exit nozzles is generated by jet-pumping effect. Elimination of the delicate and easily damaged moving parts in the actuator simplifies its manufacture and assembly. Operating frequency is adjusted by the length of feedback loop path. Laboratory investigations concentrated on the propagation processes taking place in the loop

Threshhold analysis of phase locked loops

Computer technique for predicting threshold in phased locked loops with and without frequency modulatio

Systematic Comparison of HF CMOS Transconductors

Transconductors are commonly used as active elements in high-frequency (HF) filters, amplifiers, mixers, and oscillators. This paper reviews transconductor design by focusing on the V-I kernel that determines the key transconductor properties. Based on bandwidth considerations, simple V-I kernels with few or no internal nodes are preferred. In a systematic way, virtually all simple kernels published in literature are generated. This is done in two steps: 1) basic 3-terminal transconductors are covered and 2) then five different techniques to combine two of them in a composite V-I kernel. In order to compare transconductors in a fair way, a normalized signal-to-noise ratio (NSNR) is defined. The basic V-I kernels and the five classes of composite V-I kernels are then compared, leading to insight in the key mechanisms that affect NSNR. Symbolic equations are derived to estimate NSNR, while simulations with more advanced MOSFET models verify the results. The results show a strong tradeoff between NSNR and transconductance tuning range. Resistively generated MOSFETs render the best NSNR results and are robust for future technology developments