Double-sampled cascaded sigma-delta modulator topologies for low oversampling ratios

This paper presents novel double-sampling cascaded sigma-delta modulator topologies for wideband applications. The proposed modulator structures employ finite impulse response (FIR) noise transfer function (NTF) to achieve the aggressive noise shaping with an additional zero at the half of the sampling frequency to alleviate the quantization noise folding. Cascading of the proposed modulator structures is very simple without any additional circuit requirements.Comisión Interministerial de Ciencia y Tecnología TIC2003-0235

Design of a wideband low-power continuous-time sigma-delta (ΣΔ) analog-to-digital converter (ADC) in 90nm CMOS technology

The growing trend in VLSI systems is to shift more signal processing functionality from analog to digital domain to reduce manufacturing cost and improve reliability. It has resulted in the demand for wideband high-resolution analog-to-digital converters (ADCs). There are many different techniques for doing analog-to-digital conversions. Oversampling ADC based on sigma-delta (ΣΔ) modulation is receiving a lot of attention due to its significantly relaxed matching requirements on analog components. Moreover, it does not need a steep roll-off anti-aliasing filter. A ΣΔ ADC can be implemented either as a discrete time system or a continuous time one. Nowadays growing interest is focused on the continuous-time ΣΔ ADC for its use in the wideband and low-power applications, such as medical imaging, portable ultrasound systems, wireless receivers, and test equipments. A continuous-time ΣΔ ADC offers some important advantages over its discrete-time counterpart, including higher sampling frequency, intrinsic anti-alias filtering, much relaxed sampling network requirements, and low-voltage implementation. Especially it has the potential in achieving low power consumption. This dissertation presents a novel fifth-order continuous-time ΣΔ ADC which is implemented in a 90nm CMOS technology with single 1.0-V power supply. To speed up design process, an improved direct design method is proposed and used to design the loop filter transfer function. To maximize the in-band gain provided by the loop filter, thus maximizing in-band noise suppression, the excess loop delay must be kept minimum. In this design, a very low latency 4-bit flash quantizer with digital-to-analog (DAC) trimming is utilized. DAC trimming technique is used to correct the quantizer offset error, which allows minimum-sized transistors to be used for fast and low-power operation. The modulator has sampling clock of 800MHz. It achieves a dynamic range (DR) of 75dB and a signal-to-noise-and-distortion ratio (SNDR) of 70dB over 25MHz input signal bandwidth with 16.4mW power dissipation. Our work is among the most improved published to date. It uses the lowest supply voltage and has the highest input signal bandwidth while dissipating the lowest power among the bandwidths exceeding 15MHz

Theory and applications of delta-sigma analogue-to-digital converters without negative feedback

Analog-to-digital converters play a crucial role in modern audio and communication design. Conventional Nyquist converters are suitable only for medium resolutions and require analog components that are precise and highly immune to noise and interference. In contrast, oversampling converters can achieve high resolutions (>20bits) and can be implemented using straightforward, high-tolerance analog components. In conventional oversampled modulators, negative feedback is applied in order to control the dynamic behavior of a system and to realize the attenuation of the quantization noise in the signal band due to noise shaping. However, feedback can also introduce undesirable effects such as limit cycles, jitter problems in continuous-time topologies, and infinite impulse responses. Additionally, it increases the system complexity due to extra circuit components such as nonlinear multi-bit digital-to-analog converters in the feedback path. Moreover, in certain applications such as wireless, biomedical sensory, or microphone implementations feedback cannot be applied. As a result, the main goal of this thesis is to develop sigma-delta data converters without feedback. Various new delta-sigma analog-to-digital converter topologies are explored their mathematical models are presented. Simulations are carried out to validate these models and to show performance results. Specifically, two topologies, a first-order and a second-order oscillator-based delta-sigma modulator without feedback are described in detail. They both can be implemented utilizing VCOs and standard digital gates, thus requiring only few components. As proof of concept, two digital microphones based on these delta-sigma converters without feedback were implemented and experimental results are given. These results show adequate performance and provide a new approach of measuring

Multirate cascaded discrete-time low-pass ΔΣ modulator for GSM/Bluetooth/UMTS

This paper shows that multirate processing in a cascaded discrete-time ΔΣ modulator allows to reduce the power consumption by up to 35%. Multirate processing is possible in a discrete-time ΔΣ modulator by its adaptibility with the sampling frequency. The power reduction can be achieved by relaxing the sampling speed of the first stage and increasing it appropriately in the second stage. Furthermore, a cascaded ΔΣ modulator enables the power efficient implementation of multiple communication standards.@The advantages of multirate cascaded ΔΣ modulators are demonstrated by comparing the performance of single-rate and multirate implementations using behavioral-level and circuit-level simulations. This analysis has been further validated with the design of a multirate cascaded triple-mode discrete-time ΔΣ modulator. A 2-1 multirate low-pass cascade, with a sampling frequency of 80 MHz in the first stage and 320 MHz in the second stage, meets the requirements for UMTS. The first stage alone is suitable for digitizing Bluetooth and GSM with a sampling frequency of 90 and 50 MHz respectively. This multimode ΔΣ modulator is implemented in a 1.2 V 90 nm CMOS technology with a core area of 0.076 mm2. Measurement results show a dynamic range of 66/77/85 dB for UMTS/ Bluetooth/GSM with a power consumption of 6.8/3.7/3.4 mW. This results in an energy per conversion step of 1.2/0.74/2.86 pJ

Design, analysis and evaluation of sigma-delta based beamformers for medical ultrasound imaging applications

The inherent analogue nature of medical ultrasound signals in conjunction with the abundant merits provided by digital image acquisition, together with the increasing use of relatively simple front-end circuitries, have created considerable demand for single-bit beamformers in digital ultrasound imaging systems. Furthermore, the increasing need to design lightweight ultrasound systems with low power consumption and low noise, provide ample justification for development and innovation in the use of single-bit beamformers in ultrasound imaging systems. The overall aim of this research program is to investigate, establish, develop and confirm through a combination of theoretical analysis and detailed simulations, that utilize raw phantom data sets, suitable techniques for the design of simple-to-implement hardware efficient digital ultrasound beamformers to address the requirements for 3D scanners with large channel counts, as well as portable and lightweight ultrasound scanners for point-of-care applications and intravascular imaging systems. In addition, the stability boundaries of higher-order High-Pass (HP) and Band-Pass (BP) Σ−Δ modulators for single- and dual- sinusoidal inputs are determined using quasi-linear modeling together with the describing-function method, to more accurately model the modulator quantizer. The theoretical results are shown to be in good agreement with the simulation results for a variety of input amplitudes, bandwidths, and modulator orders. The proposed mathematical models of the quantizer will immensely help speed up the design of higher order HP and BP Σ−Δ modulators to be applicable for digital ultrasound beamformers. Finally, a user friendly design and performance evaluation tool for LP, BP and HP modulators is developed. This toolbox, which uses various design methodologies and covers an assortment of modulators topologies, is intended to accelerate the design process and evaluation of modulators. This design tool is further developed to enable the design, analysis and evaluation of beamformer structures including the noise analyses of the final B-scan images. Thus, this tool will allow researchers and practitioners to design and verify different reconstruction filters and analyze the results directly on the B-scan ultrasound images thereby saving considerable time and effort

A SigmaDelta modulator for digital hearing instruments using 0.18 mum CMOS technology.

This thesis develops the design methodology for a low-voltage low-power SigmaDelta Modulator, realized using a switched op-amp technique that can be used in a hearing instrument. Switched op-amp implementation allows scaling down the design to the latest CMOS technology. A single-loop second-order SigmaDelta Modulator topology is chosen. The modulator circuit features reduced complexity, area reduction and low conversion energy. The modulator has a sampling rate of 8.2 MHz with an over-sampling ratio (OSR) of 256 to provide an audio bandwidth of 16 kHz. The modulator is implemented in a 0.18 mum digital CMOS technology with metal-to-metal sandwich structure capacitors. The modulator operates with a supply voltage of 1.8 V. The active area is 0.403 mm2. The modulator achieves a 98 dB signal-to-noise-and-distortion ratio (SNDR) and a 100 dB dynamic range (DR) at a Nyquist conversion rate of 32 kHz and consumes 1321 muW with a joule/conversion figure of merit equal to 161 x 10-12 J/s. The design methodology is developed through the extensive use of simulation tools. The behaviour simulation is carried out using Matlab/SIMULINK while circuits are simulated with Hspice using the Cadence design tools. Full-custom layout for the analog and the digital circuits is performed using the Cadence design tool. Post-processing simulation of the extracted modulator with parasitic verifies that results meet the requirements. The design has been sent to CMC for fabrication. Source: Masters Abstracts International, Volume: 43-03, page: 0947. Adviser: W. C. Miller. Thesis (M.A.Sc.)--University of Windsor (Canada), 2004

Bandpass delta-sigma modulators for radio receivers

This thesis concerns discrete-time (DT) bandpass (BP) ΔΣ modulators targeted for intermediate frequency (IF) analog-to-digital (A/D) conversion in radio receivers. The receiver architecture adopted has to be capable of operating with different radio frequencies, channel bandwidths, and modulation techniques. This is necessary in order to achieve an extensive operating area and the possibility of utilizing a local mobile phone standard or a standard suitable for a specific service. The digital IF receiver is a good choice for a multi-mode and multi-band mobile phone receiver, because the signal demodulation and channel filtering are performed in the digital domain. This increases the flexibility of the receiver and relieves the design of the baseband part, but an A/D conversion with high dynamic range and low power dissipation is required. BP ΔΣ modulators are capable of converting a high-frequency narrow band signal and are therefore suitable for signal digitization in an IF receiver. First, the theory of BP ΔΣ modulators is introduced. It has been determined that resonators are the most critical circuit blocks in the implementation of a high performance BP ΔΣ modulator. Different DT resonator topologies are studied and a double-delay (DD) resonator is found to be the best candidate for a high quality resonator. A new DD switched-capacitor (SC) resonator structure has been designed. Furthermore, two evolution versions of the designed SC resonator are presented and their nonidealities are analyzed. The three designed DD SC resonator structures are a main point of the thesis, together with the experimental results. Five different DT BP ΔΣ modulator circuit structures have been implemented and measured. All three of the designed SC resonators are used in the implemented circuits. The experimental work consists of both single-bit and multi-bit structures, as well as both single-loop and cascade architectures. The circuits have been implemented with a 0.35 μm (Bi)CMOS technology and operate with a 3.0 V supply. The measured maximum signal-to-noise-and-distortion ratios (SNDRs) are 78 dB over 270 kHz (GSM), 75 dB over 1.25 MHz (IS-95), 69 dB over 1.762 MHz (DECT), and 48 dB over 3.84 MHz (WCDMA) bandwidths using a 60 MHz IF signal.reviewe

Multi-band Oversampled Noise Shaping Analog to Digital Conversion

Oversampled noise shaping analog to digital (A/D) converters, which are commonly known as delta-sigma (ΔΣ) converters, have the ability to convert relatively low bandwidth signals with very high resolution. Such converters achieve their high resolution by oversampling, as well as processing the signal and quantization noise with different transfer functions. The signal transfer function (STF) is typically a delay over the signal band while the noise transfer function (NTF) is designed to attenuate quantization noise in the signal band. A side effect of the NTF is an amplification of the noise outside the signal band. Thus, a digital filter subsequently attenuates the out-of-band quantization noise. The focus of this thesis is the investigation of ΔΣ architectures that increase the bandwidth where high resolution conversion can be achieved. It uses parallel architectures exploiting frequency or time slicing to meet this objective. Frequency slicing involves quantizing different portions of the signal frequency spectrum using several quantizers in parallel and then combining the results of the quantizers to form an overall result. Time slicing involves quantizing various groups of time domain signal samples with different quantizers in parallel and then combining the results of the quantizers to form an overall output. Several interesting observations can be made from this general perspective of frequency and time slicing. Although the representation of a signal are completely equivalent in time or frequency, the thesis shows that this is not the case for known frequency and time sliced A/D architectures. The performance of such systems under ideal conditions are compared for PCM as well as for ΔΣ A/D converters. A multi-band frequency sliced architecture for delta-sigma conversion is proposed and its performance is included in the above comparison. The architecture uses modulators which realize different NTFs for different portions of the signal band. Each band is converted in parallel. A bank of FIR filters attenuates the out of-band noise for each band and achieves perfect reconstruction of the signal component. A design procedure is provided for the design of the filter bank with reduced computational complexity. The use of complex NTFs in the multi-band ΔΣ architecture is also proposed. The peformance of real and complex NTFs is compared. Performance evaluations are made for ideal systems as well as systems suffering from circuit implementation imperfections such as finite opamp gain and mismatched capacitor ratios

Comparison of Simulation Methods of Single and Multi-Bit Continuous Time Sigma Delta Modulators

Continuous time Sigma Delta Modulators (CT ΣΔMs) are a type of analog to digital converter (ADC) that are used in mixed signal systems to convert analog signals into digital signals. ADCs typically require antialiasing filter; however antialiasing filters are inherent in CT ΣΔMs, and therefore they require less circuitry and less power than other ADC architectures that require separate antialiasing filters. As a result, CT ΣΔM ADC architectures are preferred in many mixed signal electronic applications. Because of the mixed signal nature of CT ΣΔMs, they can be difficult to simulate. In this thesis, various methods for simulating single-bit and multi-bit CT ΣΔMs are developed and these simulations include the bilinear transform or trapezoidal integration, impulse invariance transform, midpoint integration, Simpson’s rule, delta transform or Euler’s forward integration rule and Simulink modeling. These methods are compared with respect to speed which is given by the total simulation time, accuracy which is given by the signal to noise ratio (SNR) value and the simplicity of the simulation method. The CT ΣΔMs have been extended from first order up to fifth order with one, two and three bit quantizers. Also, the frequency domain analysis is done for all the orders of CT ΣΔMs. The results show that the numerical integration methods are more accurate and faster than Simulink. However, CT ΣΔM simulations using Simulink are simpler because of the availability of the required blocks in Simulink. The overall comparison shows that the numerical integration methods can perform better than Simulink models. The frequency domain analysis proves the correctness of the use of numerical integration methods for CT ΣΔM simulations