Reliability of pulse photoplethysmography sensors: Coverage using different setups and body locations

Pulse photoplethysmography (PPG) is a simple and economical technique for obtaining cardiovascular information. In fact, PPG has become a very popular technology among wearable devices. However, the PPG signal is well-known to be very vulnerable to artifacts, and a good quality signal cannot be expected for most of the time in daily life. The percentage of time that a given measurement can be estimated (e.g., pulse rate) is denoted coverage (C), and it is highly dependent on the subject activity and on the configuration of the sensor, location, and stability of contact. This work aims to quantify the coverage of PPG sensors, using the simultaneously recorded electrocardiogram as a reference, with the PPG recorded at different places in the body and under different stress conditions. While many previous works analyzed the feasibility of PPG as a surrogate for heart rate variability analysis, there exists no previous work studying coverage to derive other cardiovascular indices. We report the coverage not only for estimating pulse rate (PR) but also for estimating pulse arrival time (PAT) and pulse amplitude variability (PAV). Three different datasets are analyzed for this purpose, consisting of a tilt-table test, an acute emotional stress test, and a heat stress test. The datasets include 19, 120, and 51 subjects, respectively, with PPG at the finger and at the forehead for the first two datasets and at the earlobe, in addition, for the latter. C ranges from 70% to 90% for estimating PR. Regarding the estimation of PAT, C ranges from 50% to 90%, and this is very dependent on the PPG sensor location, PPG quality, and the fiducial point (FP) chosen for the delineation of PPG. In fact, the delineation of the FP is critical in time for estimating derived series such as PAT due to the small dynamic range of these series. For the estimation of PAV, the C rates are between 70% and 90%. In general, lower C rates have been obtained for the PPG at the forehead. No difference in C has been observed between using PPG at the finger or at the earlobe. Then, the benefits of using either will depend on the application. However, different C rates are obtained using the same PPG signal, depending on the FP chosen for delineation. Lower C is reported when using the apex point of the PPG instead of the maximum flow velocity or the basal point, with a difference from 1% to even 10%. For further studies, each setup should first be analyzed and validated, taking the results and guidelines presented in this work into account, to study the feasibility of its recording devices with respect to each specific application

Cardiac Inter Beat Interval and Atrial Fibrillation Detection using Video Plethysmography

Facial videoplethysmography provides non-contact measurement of heart activity based on blood volume pulsations detected in facial tissue. Typically, the signal is extracted using a simple webcam followed by elaborated signal processing methods, and provides limited accuracy of time-domain characteristics. In this study, we explore the possibility of providing accurate time-domain pulse and inter-beat interval measurements using a high- quality image sensor camera and various signal processing approaches, and use these measurements to diagnose atrial fibrillation. We capture synchronized signals using a high- quality camera, a simple webcam, an earlobe photoplethysmography sensor, and a body- surface electrocardiogram from a large group of subjects, including subjects diagnosed with cardiac arrhythmias. All signals are processed using both blind source separation and color conversion. We then assess accuracy of IBI detection, heart rate variability estimation, and atrial fibrillation diagnose by comparing to a body-surface electrocardiogram. We present a new heart variability indicator for blood volume pulsating signals. Our results demonstrate that the accuracy of a facial VPG system is greatly improved when using a high-quality camera. Coupling the high-quality camera with color conversion from RGB to Hue provides a level of accuracy equivalent to that of commercially available photoplethysmography sensors, and offers a non-contact alternative to current technology for heart rate variability assessment and atrial fibrillation screening

A Deep Learning Classifier for Detecting Atrial Fibrillation in Hospital Settings Applicable to Various Sensing Modalities

Cardiac signals provide variety of information related to the patient\u27s health. One of the most important is for medical experts to diagnose the functionality of a patient’s heart. This information helps the medical experts monitor heart disease such as atrial fibrillation and heart failure. Atrial fibrillation (AF) is one of the most major diseases that are threatening patients’ health. Medical experts measure cardiac signals usng the Electrocardiogram (ECG or EKG), the Photoplethysmogram (PPG), and more recently the Videoplethysmogram (VPG). Then they can use these measurements to analyze the heart functionality to detect heart diseases. In this study, these three major cardiac signals were used with different classification methodologies such as Basic Thresholding Classifiers (BTC), Machine Learning (SVM) classifiers, and deep learning classifiers based on Convolutional Neural Networks (CNN) to detect AF. To support the work, cardiac signals were acquired from forty-six AF subjects scheduled for cardioversion who were enrolled in a clinical study that was approved by the Internal Review Committees to protect human subjects at the University of Rochester Medical Center (URMC, Rochester, NY), and the Rochester Institute of Technology (RIT, Rochester, NY). The study included synchronized measurements of 5 minutes and 30 seconds of ECG, PPG, VPG 180Hz (High-quality camera), VPG 30 Hz (low quality webcam), taken before and after cardioversion of AF subjects receiving treatment at the AF Clinic of URMC. These data are subjected to BTC, SVM, and CNN classifiers to detect AF and compare the result for each classifier depending on the signal type. We propose a deep learning approach that is applicable to different kinds of cardiac signals to detect AF in a similar manner. By building this technique for different sensors we aim to provide a framework to implement a technique that can be used for most devices, such as, phones, tablets, PCs, ECG devices, and wearable PPG sensors. This conversion of the different sensing platforms provides a single AF detection classifier that can support a complete monitoring cycle that is referring to screen the patient whether at a hospital or home. By using that, the risk factor of heart attack, stroke, or other kind of heart complications can be reduced to a low level to prevent major dangers, since increasing monitoring AF patients helps to predict the disease at an early stage as well as track its progress. We show that the proposed approach provides around 99% accuracy for each type of classifier on the test dataset, thereby helping generalize AF detection by simplifying implementation using a sensor-agnostic deep learning model

Deep Learning-based Handheld Device-Enabled Symptom-driven Recording: A Pragmatic Approach for the Detection of Post-ablation Atrial Fibrillation Recurrence

Objective: Symptom-driven electrocardiogram (ECG) recording plays a significant role in the detection of post-ablation atrial fibrillation recurrence (AFR). However, making timely medical contact whenever symptoms occur may not be practical. Herein, a deep learning (DL)-based handheld device was deployed to facilitate symptom-driven monitoring. Methods: A cohort of patients with paroxysmal atrial fibrillation (AF) was trained to use a DL-based handheld device to record ECG signals whenever symptoms presented after the ablation. Additionally, 24-hour Holter monitoring and 12-lead ECG were scheduled at 3, 6, 9, and 12 months post-ablation. The detection of AFR by the different modalities was explored. Results: A total of 22 of 67 patients experienced AFR. The handheld device and 24-hour Holter monitor detected 19 and 8 AFR events, respectively, five of which were identified by both modalities. A larger portion of ECG tracings was recorded for patients with than without AFR [362(330) vs. 132(133), P=0.01)], and substantial numbers of AFR events were recorded from 18:00 to 24:00. Compared to Holter, more AFR events were detected by the handheld device in earlier stages (HR=1.6, 95% CI 1.2–2.2, P<0.01). Conclusions: The DL-based handheld device-enabled symptom-driven recording, compared with the conventional monitoring strategy, improved AFR detection and enabled more timely identification of symptomatic episodes

pyPPG: A Python toolbox for comprehensive photoplethysmography signal analysis

Photoplethysmography is a non-invasive optical technique that measures changes in blood volume within tissues. It is commonly and increasingly used for in a variety of research and clinical application to assess vascular dynamics and physiological parameters. Yet, contrary to heart rate variability measures, a field which has seen the development of stable standards and advanced toolboxes and software, no such standards and open tools exist for continuous photoplethysmogram (PPG) analysis. Consequently, the primary objective of this research was to identify, standardize, implement and validate key digital PPG biomarkers. This work describes the creation of a standard Python toolbox, denoted pyPPG, for long-term continuous PPG time series analysis recorded using a standard finger-based transmission pulse oximeter. The improved PPG peak detector had an F1-score of 88.19% for the state-of-the-art benchmark when evaluated on 2,054 adult polysomnography recordings totaling over 91 million reference beats. This algorithm outperformed the open-source original Matlab implementation by ~5% when benchmarked on a subset of 100 randomly selected MESA recordings. More than 3,000 fiducial points were manually annotated by two annotators in order to validate the fiducial points detector. The detector consistently demonstrated high performance, with a mean absolute error of less than 10 ms for all fiducial points. Based on these fiducial points, pyPPG engineers a set of 74 PPG biomarkers. Studying the PPG time series variability using pyPPG can enhance our understanding of the manifestations and etiology of diseases. This toolbox can also be used for biomarker engineering in training data-driven models. pyPPG is available on physiozoo.orgComment: The manuscript was submitted to "Physiological Measurement" on September 5, 202

Mobile health solutions for atrial fibrillation detection and management: a systematic review

AimWe aimed to systematically review the available literature on mobile Health (mHealth) solutions, including handheld and wearable devices, implantable loop recorders (ILRs), as well as mobile platforms and support systems in atrial fibrillation (AF) detection and management.MethodsThis systematic review was conducted in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-analyses (PRISMA) guidelines. The electronic databases PubMed (NCBI), Embase (Ovid), and Cochrane were searched for articles published until 10 February 2021, inclusive. Given that the included studies varied widely in their design, interventions, comparators, and outcomes, no synthesis was undertaken, and we undertook a narrative review.ResultsWe found 208 studies, which were deemed potentially relevant. Of these studies included, 82, 46, and 49 studies aimed at validating handheld devices, wearables, and ILRs for AF detection and/or management, respectively, while 34 studies assessed mobile platforms/support systems. The diagnostic accuracy of mHealth solutions differs with respect to the type (handheld devices vs wearables vs ILRs) and technology used (electrocardiography vs photoplethysmography), as well as application setting (intermittent vs continuous, spot vs longitudinal assessment), and study population.ConclusionWhile the use of mHealth solutions in the detection and management of AF is becoming increasingly popular, its clinical implications merit further investigation and several barriers to widespread mHealth adaption in healthcare systems need to be overcome

Pulse Rate Variability for the Assessment of Cardiovascular Changes

Pulse rate variability (PRV) describes the way pulse rate changes through time and is measured from pulsatile signals such as the photoplethysmogram (PPG). It has been proposed as a surrogate for heart rate variability (HRV). Nonetheless, the relationship between these variables is not entirely clear, probably due to both physiological and technical aspects involved in the extraction of PRV. Moreover, the effects of cardiovascular changes on PRV have not been elucidated. In this thesis, four studies were performed to (1) determine the best combination of some technical aspects for the extraction of PRV from PPG signals; (2) evaluate the relationship between PRV and HRV under different cardiovascular conditions; and (3) explore the effects of cardiovascular changes on PRV. First, PRV extraction gave lower errors when (1) signals were acquired for at least 120 s with a 256 Hz sampling rate and filtered with lower low cut-off frequencies and elliptic, equiripple or Parks-McClellan filter; (2) cardiac cycles were determined using the D2max algorithm and the a fiducial points; and (3) the Fast Fourier Transform was applied to obtain frequency spectra. Secondly, the relationship between HRV and PRV was found to be affected by cold exposure and changes in blood pressure, while PRV was found to be different at different body sites. Finally, PRV was affected by haemodynamic changes, such as target flow, stroke rate and blood pressure, both in an in-vitro model and in-vivo data. Additionally, PRV was found to be a potential tool for the estimation of blood pressure, with errors as low as 1:54 ± 0:17 mmHg, 1:07 ± 0:06 mmHg and 1:22 ± 0:09 mmHg for the estimation of systolic, diastolic and mean arterial pressure. Although more studies are needed to fully understand PRV and its clinical potential, PRV should not be regarded as the same as HRV, and it could be consider as a potential valuable biomarker for cardiovascular health

Sources of inaccuracy in photoplethysmography for continuous cardiovascular monitoring

Photoplethysmography (PPG) is a low-cost, noninvasive optical technique that uses change in light transmission with changes in blood volume within tissue to provide information for cardiovascular health and fitness. As remote health and wearable medical devices become more prevalent, PPG devices are being developed as part of wearable systems to monitor parameters such as heart rate (HR) that do not require complex analysis of the PPG waveform. However, complex analyses of the PPG waveform yield valuable clinical information, such as: blood pressure, respiratory information, sympathetic nervous system activity, and heart rate variability. Systems aiming to derive such complex parameters do not always account for realistic sources of noise, as testing is performed within controlled parameter spaces. A wearable monitoring tool to be used beyond fitness and heart rate must account for noise sources originating from individual patient variations (e.g., skin tone, obesity, age, and gender), physiology (e.g., respiration, venous pulsation, body site of measurement, and body temperature), and external perturbations of the device itself (e.g., motion artifact, ambient light, and applied pressure to the skin). Here, we present a comprehensive review of the literature that aims to summarize these noise sources for future PPG device development for use in health monitoring

Atrial Fibrillation Detection from Photoplethysmography Data Using Artificial Neural Networks

Atrial fibrillation (AF) is one of the most common types of cardiac arrhythmia- especially in elderly and hypertensive patients, leading to increased risk of heart failure and stroke. Therefore, early screening and diagnosis can reduce the AF impact. The development of photoplethysmography (PPG) technology has enabled comfortable and unobtrusive physiological monitoring of heart rate with a wrist-worn device. It is important to examine the possibility of using PPG signal to diagnose AF in real-world situations. There are several recent studies classifying cardiac arrhythmias with artificial neural networks (ANN) based on RR intervals derived from ECG, but no one has evaluated ANN approach for wrist PPG data. The aim of this MSc thesis is to present an ANN-based classifier to detect AF episodes from PPG data. The used classifier is multilayer perceptron (MLP) that utilizes backpropagation for learning. This classifier is able to distinguish between AF and non-AF rhythms. The input feature of the ANN is based on the information obtained from an interbeat interval (IBI) sequence of 30 consecutive PPG pulses. The PPG dataset was acquired with PulseOn (PO) wearable optical heart rate monitoring device and the recordings were performed in the post-anesthesia care unit of Tampere University Hospital. The study was approved by the local ethical committee. The guidelines of the Declaration of Helsinki were followed. In total 30 patients with multiple comorbidities were monitored during routine postoperative treatment. 15 subjects had sinus rhythm (SR) and 15 had AF during the recording. The average duration of each recording was 1.5 hours. The monitoring included standard ECG as a reference and a wrist-worn PPG monitor with green and infrared light sources. As IBIs extracted from the PPG signals are highly sensitive to motion artefacts, IBI reliability was automatically evaluated using PPG waveform and acceleration signals before AF detection. Based on the achieved results, the ANN algorithm demonstrated excellent performance at recognizing AF from SR, using wrist PPG data