A Low-Power BFSK/OOK Transmitter for Wireless Sensors

In recent years, significant improvements in semiconductor technology have allowed consistent development of wireless chipsets in terms of functionality and form factor. This has opened up a broad range of applications for implantable wireless sensors and telemetry devices in multiple categories, such as military, industrial, and medical uses. The nature of these applications often requires the wireless sensors to be low-weight and energy-efficient to achieve long battery life. Among the various functions of these sensors, the communication block, used to transmit the gathered data, is typically the most power-hungry block. In typical wireless sensor networks, transmission range is below 10 meters and required radiated power is below 1 milliwatt. In such cases, power consumption of the frequency-synthesis circuits prior to the power amplifier of the transmitter becomes significant. Reducing this power consumption is currently the focus of various research endeavors. A popular method of achieving this goal is using a direct-modulation transmitter where the generated carrier is directly modulated with baseband data using simple modulation schemes. Among the different variations of direct-modulation transmitters, transmitters using unlocked digitally-controlled oscillators and transmitters with injection or resonator-locked oscillators are widely investigated because of their simple structure. These transmitters can achieve low-power and stable operation either with the help of recalibration or by sacrificing tuning capability. In contrast, phase-locked-loop-based (PLL) transmitters are less researched. The PLL uses a feedback loop to lock the carrier to a reference frequency with a programmable ratio and thus achieves good frequency stability and convenient tunability. This work focuses on PLL-based transmitters. The initial goal of this work is to reduce the power consumption of the oscillator and frequency divider, the two most power-consuming blocks in a PLL. Novel topologies for these two blocks are proposed which achieve ultra-low-power operation. Along with measured performance, mathematical analysis to derive rule-of-thumb design approaches are presented. Finally, the full transmitter is implemented using these blocks in a 130 nanometer CMOS process and is successfully tested for low-power operation

A GHz-range, High-resolution Multi-modulus Prescaler for Extreme Environment Applications

The generation of a precise, low-noise, reliable clock source is critical to developing mixed-signal and digital electronic systems. The applications of such a clock source are greatly expanded if the clock source can be configured to output different clock frequencies. The phase-locked loop (PLL) is a well-documented architecture for realizing this configurable clock source. Principle to the configurability of a PLL is a multi-modulus divider. The resolution of this divider (or prescaler) dictates the resolution of the configurable PLL output frequency. In integrated PLL designs, such a multi-modulus prescaler is usually sourced from a GHz-range voltage-controlled oscillator. Therefore, a fully-integrated PLL ASIC requires the development of a high-speed, high-resolution multi-modulus prescaler. The design challenges associated with developing such a prescaler are compounded when the application requires the device to operate in an extreme environment. In these extreme environments (often extra-terrestrial), wide temperature ranges and radiation effects can adversely affect the operation of electronic systems. Even more problematic is that extreme temperatures and ionizing radiation can cause permanent damage to electronic devices. Typical commercial-off-the-shelf (COTS) components are not able withstand such an environment, and any electronics operating in these extreme conditions must be designed to accommodate such operation. This dissertation describes the development of a high-speed, high-resolution, multi-modulus prescaler capable of operating in an extreme environment. This prescaler has been developed using current-mode logic (CML) on a 180-nm silicon-germanium (SiGe) BiCMOS process. The prescaler is capable of operating up to at least 5.4 GHz over a division range of 16-48 with a total of 27 configurable moduli. The prescaler is designed to provide excellent ionizing radiation hardness, single-event latch-up (SEL) immunity, and single-event upset (SEU) resistance over a temperature range of −180°C to 125°C

Integrated radio frequency synthetizers for wireless applications

This thesis consists of six publications and an overview of the research topic, which is also a summary of the work. The research described in this thesis concentrates on the design of phase-locked loop radio frequency synthesizers for wireless applications. In particular, the focus is on the implementation of the prescaler, the phase detector, and the chargepump. This work reviews the requirements set for the frequency synthesizer by the wireless standards, and how these requirements are derived from the system specifications. These requirements apply to both integer-N and fractional-N synthesizers. The work also introduces the special considerations related to the design of fractional-N phase-locked loops. Finally, implementation alternatives for the different building blocks of the synthesizer are reviewed. The presented work introduces new topologies for the phase detector and the chargepump, and improved topologies for high speed CMOS prescalers. The experimental results show that the presented topologies can be successfully used in both integer-N and fractional-N synthesizers with state-of-the-art performance. The last part of this work discusses the additional considerations that surface when the synthesizer is integrated into a larger system chip. It is shown experimentally that the synthesizer can be successfully integrated into a complex transceiver IC without sacrificing the performance of the synthesizer or the transceiver.reviewe

New strategies for low noise, agile PLL frequency synthesis

Phase-Locked Loop based frequency synthesis is an essential technique employed in wireless communication systems for local oscillator generation. The ultimate goal in any design of frequency synthesisers is to generate precise and stable output frequencies with fast switching and minimal spurious and phase noise. The conflict between high resolution and fast switching leads to two separate integer synthesisers to satisfy critical system requirements. This thesis concerns a new sigma-delta fractional-N synthesiser design which is able to be directly modulated at high data rates while simultaneously achieving good noise performance. Measured results from a prototype indicate that fast switching, low noise and spurious free spectra are achieved for most covered frequencies. The phase noise of the unmodulated synthesiser was measured −113 dBc/Hz at 100 kHz offset from the carrier. The intermodulation effect in synthesisers is capable of producing a family of spurious components of identical form to fractional spurs caused in quantisation process. This effect directly introduces high spurs on some channels of the synthesiser output. Numerical and analytic results describing this effect are presented and amplitude and distribution of the resulting fractional spurs are predicted and validated against simulated and measured results. Finally an experimental arrangement, based on a phase compensation technique, is presented demonstrating significant suppression of intermodulation-borne spurs. A new technique, pre-distortion noise shaping, is proposed to dramatically reduce the impact of fractional spurs in fractional-N synthesisers. The key innovation is the introduction in the bitstream generation process of carefully-chosen set of components at identical offset frequencies and amplitudes and in anti-phase with the principal fractional spurs. These signals are used to modify the Σ-Δ noise shaping, so that fractional spurs are effectively cancelled. This approach can be highly effective in improving spectral purity and reduction of spurious components caused by the Σ-Δ modulator, quantisation noise, intermodulation effects and any other circuit factors. The spur cancellation is achieved in the digital part of the synthesiser without introducing additional circuitry. This technique has been convincingly demonstrated by simulated and experimental results

Power-efficient high-speed interface circuit techniques

Inter- and intra-chip connections have become the new challenge to enable the scaling of computing systems, ranging from mobile devices to high-end servers. Demand for aggregate I/O bandwidth has been driven by applications including high-speed ethernet, backplane micro-servers, memory, graphics, chip-to-chip and network onchip. I/O circuitry is becoming the major power consumer in SoC processors and memories as the increasing bandwidth demands larger per-pin data rate or larger I/O pin count per component. The aggregate I/O bandwidth has approximately doubled every three to four years across a diverse range of standards in different applications. However, in order to keep pace with these standards enabled in part by process-technology scaling, we will require more than just device scaling in the near future. New energy-efficient circuit techniques must be proposed to enable the next generations of handheld and high-performance computers, given the thermal and system-power limits they start facing. ^ In this work, we are proposing circuit architectures that improve energy efficiency without decreasing speed performance for the most power hungry circuits in high speed interfaces. By the introduction of a new kind of logic operators in CMOS, called implication operators, we implemented a new family of high-speed frequency dividers/prescalers with reduced footprint and power consumption. New techniques and circuits for clock distribution, for pre-emphasis and for driver at the transmitter side of the I/O circuitry have been proposed and implemented. At the receiver side, new DFE architecture and CDR have been proposed and have been proven experimentally

A high-frequency quad-modulus prescaler for fractional-N frequency synthesizer

Master'sMASTER OF ENGINEERIN

CMOS dual-modulus prescaler design for RF frequency synthesizer applications.

Ng Chong Chon.Thesis (M.Phil.)--Chinese University of Hong Kong, 2005.Includes bibliographical references (leaves 100-103).Abstract in English and Chinese.摘要 --- p.iiiAcknowledgments --- p.ivContents --- p.viList of Figures --- p.ixList of Tables --- p.xiiChapter Chapter 1 --- Introduction --- p.1Chapter 1.1 --- Motivation --- p.1Chapter 1.2 --- Thesis Organization --- p.4Chapter Chapter 2 --- DMP Architecture --- p.6Chapter 2.1 --- Conventional DMP --- p.6Chapter 2.1.1 --- Operating Principle --- p.7Chapter 2.1.2 --- Disadvantages --- p.10Chapter 2.2 --- Pre-processing Clock Architecture --- p.10Chapter 2.2.1 --- Operating Principle --- p.11Chapter 2.2.2 --- Advantages and Disadvantages --- p.12Chapter 2.3 --- Phase-switching Architecture --- p.13Chapter 2.3.1 --- Operating Principle --- p.13Chapter 2.3.2 --- Advantages and Disadvantages --- p.14Chapter 2.4 --- Summary --- p.15Chapter Chapter 3 --- Full-Speed Divider Design --- p.16Chapter 3.1 --- Introduction --- p.16Chapter 3.2 --- Working Principle --- p.16Chapter 3.3 --- Design Issues --- p.18Chapter 3.4 --- Device Sizing --- p.19Chapter 3.5 --- Layout Considerations --- p.20Chapter 3.6 --- Input Sensitivity --- p.22Chapter 3.7 --- Modeling --- p.24Chapter 3.8 --- Review on Different Divider Designs --- p.28Chapter 3.8.1 --- Divider with Dynamic-Loading Technique --- p.28Chapter 3.8.2 --- Divider with Negative-Slew Technique --- p.30Chapter 3.8.3 --- LC Injection-Locked Frequency Divider --- p.32Chapter 3.8.4 --- Dynamic True Single Phase Clock Frequency Divider --- p.34Chapter 3.9 --- Summary --- p.42Chapter Chapter 4 --- 3V 900MHz Low Noise DMP --- p.43Chapter 4.1 --- Introduction --- p.43Chapter 4.2 --- Proposed DMP Topology --- p.46Chapter 4.3 --- Circuit Design and Implementation --- p.49Chapter 4.4 --- Simulation Results --- p.51Chapter 4.5 --- Summary --- p.53Chapter Chapter 5 --- 1.5V 2.4GHz Low Power DMP --- p.54Chapter 5.1 --- Introduction --- p.54Chapter 5.2 --- Proposed DMP Topology --- p.56Chapter 5.3 --- Circuit Design and Implementation --- p.59Chapter 5.3.1 --- Divide-by-4 stage --- p.59Chapter 5.3.2 --- TSPC dividers --- p.63Chapter 5.3.3 --- Phase-selection Network --- p.63Chapter 5.3.4 --- Mode-control Logic --- p.64Chapter 5.3.5 --- Duty-cycle Transformer --- p.65Chapter 5.3.6 --- Glitch Problem --- p.66Chapter 5.3.7 --- Phase-mismatch Problem --- p.70Chapter 5.4 --- Simulation Results --- p.70Chapter 5.5 --- Summary --- p.74Chapter Chapter 6 --- 1.5V 2.4GHz Wideband DMP --- p.75Chapter 6.1 --- Introduction --- p.75Chapter 6.2 --- Proposed DMP Architecture --- p.75Chapter 6.3 --- Divide-by-4 Stage --- p.76Chapter 6.3.1 --- Current-switch Combining --- p.76Chapter 6.3.2 --- Capacitive Load Reduction --- p.77Chapter 6.4 --- Simulation Results --- p.81Chapter 6.5 --- Summary --- p.83Chapter Chapter 7 --- Experimental Results --- p.84Chapter 7.1 --- Introduction --- p.84Chapter 7.2 --- Equipment Setup --- p.84Chapter 7.3 --- Measurement Results --- p.85Chapter 7.3.1 --- 3V 900GHz Low Noise DMP --- p.85Chapter 7.3.2 --- 1.5V 2.4GHz Low Power DMP --- p.88Chapter 7.3.3 --- 1.5V 2.4GHz Wideband DMP --- p.93Chapter 7.3 --- Summary --- p.96Chapter Chapter 8 --- Conclusions and Future Works --- p.98Chapter 8.1 --- Conclusions --- p.98Chapter 8.2 --- Future Works --- p.99References --- p.100Publications --- p.10

Process and Temperature Compensated Wideband Injection Locked Frequency Dividers and their Application to Low-Power 2.4-GHz Frequency Synthesizers

There has been a dramatic increase in wireless awareness among the user community in the past five years. The 2.4-GHz Industrial, Scientific and Medical (ISM) band is being used for a diverse range of applications due to the following reasons. It is the only unlicensed band approved worldwide and it offers more bandwidth and supports higher data rates compared to the 915-MHz ISM band. The power consumption of devices utilizing the 2.4-GHz band is much lower compared to the 5.2-GHz ISM band. Protocols like Bluetooth and Zigbee that utilize the 2.4-GHz ISM band are becoming extremely popular. Bluetooth is an economic wireless solution for short range connectivity between PC, cell phones, PDAs, Laptops etc. The Zigbee protocol is a wireless technology that was developed as an open global standard to address the unique needs of low-cost, lowpower, wireless sensor networks. Wireless sensor networks are becoming ubiquitous, especially after the recent terrorist activities. Sensors are employed in strategic locations for real-time environmental monitoring, where they collect and transmit data frequently to a nearby terminal. The devices operating in this band are usually compact and battery powered. To enhance battery life and avoid the cumbersome task of battery replacement, the devices used should consume extremely low power. Also, to meet the growing demands cost and sized has to be kept low which mandates fully monolithic implementation using low cost process. CMOS process is extremely attractive for such applications because of its low cost and the possibility to integrate baseband and high frequency circuits on the same chip. A fully integrated solution is attractive for low power consumption as it avoids the need for power hungry drivers for driving off-chip components. The transceiver is often the most power hungry block in a wireless communication system. The frequency divider (prescaler) and the voltage controlled oscillator in the transmitter’s frequency synthesizer are among the major sources of power consumption. There have been a number of publications in the past few decades on low-power high-performance VCOs. Therefore this work focuses on prescalers. A class of analog frequency dividers called as Injection-Locked Frequency Dividers (ILFD) was introduced in the recent past as low power frequency division. ILFDs can consume an order of magnitude lower power when compared to conventional flip-flop based dividers. However the range of operation frequency also knows as the locking range is limited. ILFDs can be classified as LC based and Ring based. Though LC based are insensitive to process and temperature variation, they cannot be used for the 2.4-GHz ISM band because of the large size of on-chip inductors at these frequencies. This causes a lot of valuable chip area to be wasted. Ring based ILFDs are compact and provide a low power solution but are extremely sensitive to process and temperature variations. Process and temperature variation can cause ring based ILFD to loose lock in the desired operating band. The goal of this work is to make the ring based ILFDs useful for practical applications. Techniques to extend the locking range of the ILFDs are discussed. A novel and simple compensation technique is devised to compensate the ILFD and keep the locking range tight with process and temperature variations. The proposed ILFD is used in a 2.4-GHz frequency synthesizer that is optimized for fractional-N synthesis. Measurement results supporting the theory are provided

BICMOS implementation of UAA 4802.

by C.Y. Ho.Thesis (M.Phil.)--Chinese University of Hong Kong, 1989.Bibliography: leaves [147]-[148