Cooling panel wall system with difference types of cooling mediums

Global warming has caused worldwide average surface temperature to rise about 0.74oC during the past 100 years, which is partly aggravated by air-conditioning that releases chlorofluorocarbons (CFCs) and forming a vicious cycle. This paper proposes a cooling house system that can promote thermal comfort in buildings without air-conditioning. The cooling panel wall forms a part of an Integrated Building System (IBS), and is essentially made of tubes filled with either water or glycerin as the coolant. Target strength for the panel wall was designed based on the Malaysian Standard (MS) while the building ventilation system followed the American Society of Heating, Refrigerating, and Air Conditioning Engineers (ASHRAE) standard. The results are reported based on indoor and outdoor temperature difference together with relative humidity to identify the best performing house model and also coolant. The outcome of this research is expected to add value to heritage house design concepts with a better promotion of air flow and circulation in the building, without over-usage of natural resources and higher building cost to achieve the same objective

Multirate input based quasi-sliding mode control for permanent magnet synchronous motor

Permanent magnet synchronous motor field oriented control system often uses dual-loop (speed and current) cascade structure, and the dynamics speeds of the two loops mismatch. The motor’s mechanical and electrical subsystems have the typical multirate characteristics. Based on the multirate control theory, this paper proposes multirate input quasi-sliding mode algorithm for the speed control loop. Under the situation of the output data loss, the proposed algorithm builds the extended input vector with the output prediction information. Due to the extended input vector, the proposed algorithm reduces the system steady state chatterring, and then improves the performance of the whole system. Simulation and experimental results demonstrate the effectiveness of the proposed algorithm

Mathematical control of complex systems

Copyright © 2013 ZidongWang et al.This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited

Hierarchical Model Predictive/Sliding Mode control of nonlinear constrained uncertain systems

This paper presents an overview of some hierarchical control schemes composed by a high level Model Predictive Control (MPC) and a low level Sliding Mode Control (SMC). The latter is realized by using the so-called Integral Sliding Mode (ISM) control approach and is meant to reject the matched disturbances affecting the plant, thus providing a system with reduced uncertainty for the MPC design. Both continuous and discrete-time solutions are discussed in the paper. Moreover, assuming the presence of a network in the control loop, a networked version of the control scheme is presented. It is a model-based event-triggered MPC/ISM control scheme aimed at minimizing the packets transmission. The input-to-state (practical) stability properties of the proposed approaches are also addressed in the paper

Networked Control System Design and Parameter Estimation

Networked control systems (NCSs) are a kind of distributed control systems in which the data between control components are exchanged via communication networks. Because of the attractive advantages of NCSs such as reduced system wiring, low weight, and ease of system diagnosis and maintenance, the research on NCSs has received much attention in recent years. The first part (Chapter 2 - Chapter 4) of the thesis is devoted to designing new controllers for NCSs by incorporating the network-induced delays. The thesis also conducts research on filtering of multirate systems and identification of Hammerstein systems in the second part (Chapter 5 - Chapter 6). Network-induced delays exist in both sensor-to-controller (S-C) and controller-to-actuator (C-A) links. A novel two-mode-dependent control scheme is proposed, in which the to-be-designed controller depends on both S-C and C-A delays. The resulting closed-loop system is a special jump linear system. Then, the conditions for stochastic stability are obtained in terms of a set of linear matrix inequalities (LMIs) with nonconvex constraints, which can be efficiently solved by a sequential LMI optimization algorithm. Further, the control synthesis problem for the NCSs is considered. The definitions of H₂ and H∞ norms for the special system are first proposed. Also, the plant uncertainties are considered in the design. Finally, the robust mixed H₂/H∞ control problem is solved under the framework of LMIs. To compensate for both S-C and C-A delays modeled by Markov chains, the generalized predictive control method is modified to choose certain predicted future control signal as the current control effort on the actuator node, whenever the control signal is delayed. Further, stability criteria in terms of LMIs are provided to check the system stability. The proposed method is also tested on an experimental hydraulic position control system. Multirate systems exist in many practical applications where different sampling rates co-exist in the same system. The l₂-l∞ filtering problem for multirate systems is considered in the thesis. By using the lifting technique, the system is first transformed to a linear time-invariant one, and then the filter design is formulated as an optimization problem which can be solved by using LMI techniques. Hammerstein model consists of a static nonlinear block followed in series by a linear dynamic system, which can find many applications in different areas. New switching sequences to handle the two-segment nonlinearities are proposed in this thesis. This leads to less parameters to be estimated and thus reduces the computational cost. Further, a stochastic gradient algorithm based on the idea of replacing the unmeasurable terms with their estimates is developed to identify the Hammerstein model with two-segment nonlinearities. Finally, several open problems are listed as the future research directions

Fractional Order and Virtual Variable Sampling Design of Repetitive Control for Power Converters

With the growth of electricity demand and renewable energy power source, power converter becomes a more and more significant component in electrical power systems. The requirement of the power converter controller is to produce an accurate and low-distorted voltage or current under different load conditions. Although the conventional controller can meet the requirement of some applications, it requires accurate knowledge of the system model and cannot provide a satisfactory result especially under nonlinear loads or sudden load change. Repetitive control (RC) presents an attractive solution to achieve excellent steady-state tracking error and low total harmonic distortion for periodic signals, and it is increasingly applied to power converter systems. However, there are still some limitations or requirements of RC when it is applied to power electronics system: first, RC requires the system sampling frequency is a fixed value and needs to be an integral multiple of the reference frequency; second, low controller sampling frequency results in low phase lead compensation resolution in RC, which leads to control inaccuracy; third, conventional RC does not have frequency adaptability to reference frequency fluctuation, and even a small reference frequency fluctuation can lead to severe performance degradation. To overcome the conventional RC limitations, two advanced design methods are proposed in the thesis: fractional order delay and virtual variable sampling. The method of fractional order delay approximates the non-integer delay part by building a finite impulse response filter. This improved method is not only able to be applied on a period delay unit but also on phase-lead compensation. The accurate period delay and phase lead compensation show a noticeable improvement in RC performance. Although fractional order delay can meet the requirement on most of the applications, it also has a minimal adjustable range on the reference frequency. To achieve an essential solution to this problem, the virtual variable sampling (VVS) method is developed. The VVS approximates a variable sampling unit instead of the fixed system unit for RC and its filters, in which RC is able to be frequency adaptive. Comparing with the method of fractional order delay, the VVS method can provide a much more extensive adjustable range on the reference frequency. Based on the system performance under the conventional controller, power converter always has uneven distortion distribution. To further improve the stability and eliminate harmonic distortions efficiently, two selective harmonic RC schemes are introduced - nk ± m order harmonic RC and DFT-based selective harmonic RC. However, these selective RC schemes also suffer from the particular requirement of system sampling frequency and low reference frequency adaptability. Applying VVS methods on these two schemes can effectively present an improvement on their frequency adaptability. To verify the proposed methods’ effectiveness, a complete series of power electronics applications are carried out. These applications include single-phase and three-phase DC/AC power converter, single-phase AC/DC power converter, and single-phase grid-connected power converter. The detailed system modeling and the proposed RC schemes are presented for each power electronics application

Adaptive Control

Adaptive control has been a remarkable field for industrial and academic research since 1950s. Since more and more adaptive algorithms are applied in various control applications, it is becoming very important for practical implementation. As it can be confirmed from the increasing number of conferences and journals on adaptive control topics, it is certain that the adaptive control is a significant guidance for technology development.The authors the chapters in this book are professionals in their areas and their recent research results are presented in this book which will also provide new ideas for improved performance of various control application problems

Time-and event-driven communication process for networked control systems: A survey

Copyright © 2014 Lei Zou et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.In recent years, theoretical and practical research topics on networked control systems (NCSs) have gained an increasing interest from many researchers in a variety of disciplines owing to the extensive applications of NCSs in practice. In particular, an urgent need has arisen to understand the effects of communication processes on system performances. Sampling and protocol are two fundamental aspects of a communication process which have attracted a great deal of research attention. Most research focus has been on the analysis and control of dynamical behaviors under certain sampling procedures and communication protocols. In this paper, we aim to survey some recent advances on the analysis and synthesis issues of NCSs with different sampling procedures (time-and event-driven sampling) and protocols (static and dynamic protocols). First, these sampling procedures and protocols are introduced in detail according to their engineering backgrounds as well as dynamic natures. Then, the developments of the stabilization, control, and filtering problems are systematically reviewed and discussed in great detail. Finally, we conclude the paper by outlining future research challenges for analysis and synthesis problems of NCSs with different communication processes.This work was supported in part by the National Natural Science Foundation of China under Grants 61329301, 61374127, and 61374010, the Royal Society of the UK, and the Alexander von Humboldt Foundation of Germany