Advanced Circularly Polarised Microstrip Patch Antennas

The thesis describes outcomes of research on advanced circularly polarised antennas. The proposed designs are intended for integration into small mobile devices, therefore low profile and easy manufacturability are key parameters, along with good CP radiation properties. The designs were validated by simulation and measurement, and are also backed by theory and design guidelines. The primary focus is on the development of planar omnidirectional circularly polarised antennas, which are fabricated using multilayer PCB techniques and thus are lightweight and cost-efficient. Unlike in classical microstrip patch antenna designs, the groundplane of the proposed antenna was substantially reduced. This helps to achieve an omnidirectional circular polarisation pattern and miniaturize the antenna, however at the cost of increased feed circuit complexity. The basic design, its advantages and disadvantages are discussed in Section 3. In the next step, the omnidirectional circularly polarised antenna was extended with additional, advanced features. A miniaturized version is investigated, which offers a 20% footprint reduction by folding parts of the patch underneath itself. Further miniaturization is possible by increasing the dielectric constant of the substrate. A method to adjust the omnidirectional circularly polarised antenna performance by trimming four lumped capacitors is also investigated. Manufacturing inaccuracy in large scale production may cause some of the units to radiate outside of the desired frequencies. By integrating four trimmed capacitors into the antenna it can be precisely tuned to the desired band. Simulated results demonstrate this property by trimming the antenna between GPS L1 band (centre frequency at 1.575 GHz) and Galileo/Beidou-2 E2 band (1.561 GHz). Furthermore, a dual-band omnidirectional circularly polarised antenna is presented, which employs slots and capacitor loading to steer the current path of the first and second resonant mode. The design offers a small frequency ratio of 1.182. The methods to obtain a planar omnidirectional circularly polarised antenna have been further advanced to propose a reconfigurable antenna. The beam reconfiguration is capable of rotating it dipole-like radiation pattern around an axis, thus allowing reception or transmission from any spherical angle. The switching method is simple and does not require any semiconductor devices. Finally, a dual circularly polarised antenna is presented, which achieves dual-polarisation by employing even and odd modes in a coplanar waveguide. This technique allows greater flexibility and size reduction of the feed network, as two signals can be transmitted by a single multi-mode transmission line. Simulated results demonstrate this property by trimming the antenna between GPS L1 band (centre frequency at 1.575 GHz) and Galileo/Beidou-2 E2 band (1.561 GHz). Furthermore, a dual-band omnidirectional circularly polarised antenna is presented, which employs slots and capacitor loading to steer the current path of the first and second resonant mode. The design offers a small frequency ratio of 1.182. The methods to obtain a planar omnidirectional circularly polarised antenna have been further advanced to propose a reconfigurable antenna. The beam reconfiguration is capable of rotating it dipole-like radiation pattern around an axis, thus allowing reception or transmission from any spherical angle. The switching method is simple and does not require any semiconductor devices. Finally, a dual circularly polarised antenna is presented, which achieves dual-polarisation by employing even and odd modes in a coplanar waveguide. This technique allows greater flexibility and size reduction of the feed network, as two signals can be transmitted by a single multi-mode transmission line

On the development of novel multi-layer passive components and the implementation of compact wideband two-layer 4x4 Butler matrix in SIW technology

Multibeam antennas have become a key element in nowadays wireless communication systems where increased channel capacity, improved transmission quality with minimum interference and multipath phenomena are severe design constraints. These antennas are classified in two main categories namely adaptive smart antennas and switched-beam antennas. Switched-beam antennas consist of an elementary antenna array connected to a Multiple Beam Forming Network (M-BFN). Among the different M-BFNs, the Butler matrix has received particular attention as it is theoretically lossless and employs the minimum number of components to generate a given set of orthogonal beams (provided that the number of beams is a power of 2). However, the Butler matrix has a main design problem which is the presence of path crossings that has been previously addressed in different research works. Substrate Integrated Waveguide (SIW) features interesting characteristics for the design of microwave and millimetre-wave integrated circuits. SIW based components combine the advantages of the rectangular waveguide, such as the high Q factor (low insertion loss) and high power capability while being compatible with low-cost PCB and LTCC technologies. Owing to its attractive features, the use of SIW technology appears as a good candidate for the implementation of BFNs. The resulting structure is therefore suitable for both waveguide-like and planar structures. In this thesis, different novel passive components (couplers and phase shifters) have been developed exploring the multi-layer SIW technology towards the implementation of a two-layer compact 4×4 Butler matrix offering wideband performances for both transmission magnitudes and phases with good isolation and input reflection characteristics. Different techniques for the implementation of wideband fixed phase shifters in SIW technology are presented. First, a novel waveguide-based CRLH structure is proposed. The structure is based on a single-layer waveguide with shunt inductive windows (irises) and series transverse capacitive slots, suitable for SIW implementations for compact phase shifters. The structure suffers relatively large insertion loss which remains however within the typical range of non-lumped elements based CRLH implementations. Second, the well-known equal length, unequal width SIW phase shifters is discussed. These phase shifters are very adapted for SIW implementations as they fully exploit the flexibility of the SIW technology in different path shapes while offering wideband phase characteristics. To satisfy good return loss characteristics with this type of phase shifters, the length has to be compromised with respect to the progressive width variations associated with the required phase shift values. A twolayer, wideband low-loss SIW transition is then proposed. The transition is analyzed using its equivalent circuit model bringing a deeper understanding of its transmission characteristics for both amplitude and phase providing therefore the basic guidelines for electromagnetic optimization. Based on its equivalent circuit model, the transition can be optimized within the well equal-length SIW phase shifters in order to compensate its additional phase shift within the frequency band of interest. This twolayer wideband phase shifter scheme has been adopted in the final developed matrix architecture.This transition is then exploited to develop a three-layer, multiply-folded waveguide structure as a good candidate for compensated-length, variable width, low-loss, compact wideband phase shifters in SIW technology. Novel two-layer SIW couplers are also addressed. For BFNs applications, an original structure for a two-layer 90° broadband coupler is developed. The proposed coupler consists of two parallel waveguides coupled together by means of two parallel inclined-offset resonant slots in their common broad wall. A complete parametric study of the coupler is carried out including the effect of the slot length, inclination angle and offset on both the coupling level and the transmission phase. The first advantage of the proposed coupler is providing a wide coupling dynamic range by varying the slot parameters allowing the design of wideband SIW Butler matrix in two-layer topology. In addition, previously published SIW couplers suffer from direct correlation between the transmission phase and the coupling level, while the coupler, hereby proposed, allows controlling the transmission phase without significantly affecting the coupling level, making it a good candidate for BFNs employing different couplers, such as, the Nolen matrix. A novel dual-band hybrid ring coupler is also developed in multi-layer Ridged SIW (RSIW) technology. This coupler has been jointly developed with Tarek Djerafi in a collaboration scenario with Prof. Ke Wu from the Ecole Polytechnique de Montréal. The coupler has an original structure based on two concentric rings in RSIW topology with the outer ring periodically loaded with radial, stub-loaded transverse slots. A design procedure is presented based on the Transverse Resonance Method (TRM) of the ridged waveguide together with the simple design rules of the hybrid ring coupler. A C/K dual band coupler with bandwidths of 8.5% and 14.6% centered at 7.2 GHz and 20.5 GHz, respectively, is presented. The coupler provides independent dual band operation with low-dispersive wideband operation. Finally, for the Butler matrix design, the two-layer SIW implementation is explored through a two-fold enhancement approach for both the matrix electrical and physical characteristics. On the one hand, the two-layer topology allows an inherent solution for the crossing problem allowing therefore more flexibility for phase compensation over a wide frequency band. This is achieved by proper geometrical optimization of the surface on each layer and exploiting the SIW technology in the realization of variable width waveguides sections with the corresponding SIW bends. On the other hand, the two-layer SIW technology is exploited for an optimized space saving design by implementing common SIW lateral walls for the matrix adjacent components seeking maximum size reduction. The two corresponding 4×4 Butler matrix prototypes are optimized, fabricated and measured. Measured results are in good agreement with the simulated ones. Isolation characteristics better than -15 dB with input reflection levels lower than -12 dB are experimentally validated over 24% frequency bandwidth centered at 12.5 GHz. Measured transmission magnitudes and phases exhibit good dispersive characteristics of 1dB, around an average value of -6.8 dB, and 10° with respect to the theoretical phase values, respectively, over the entire frequency band

Développement de nouveaux composants passifs multicouches et l'implémentation d'une matrice de Butler large-bande et compacte en technologie GIS

Les systèmes de communications sans fils actuels imposent des contraintes très sévères en termes de la capacité du canal, la qualité de transmission tout en gardant les niveaux d'interférences et multi-trajets assez faibles. De telles contraintes ont rendu les antennes multifaisceaux un élément essentiel dans ces systèmes. Parmi les techniques permettant de réaliser une antenne multifaisceaux (sans avoir recours aux systèmes à balayages électroniques), un réseau d'antennes élémentaires est associé à un réseau d'alimentation (une matrice) à formation de faisceau (Beam Forming Network-BFN). Parmi les différents types de ces matrices, la matrice de Butler a reçu une attention particulière. Ceci est dû au fait qu'elle est théoriquement sans pertes et qu'elle emploie un nombre minimum de composants (coupleurs et déphaseurs) afin de générer l'ensemble de faisceaux orthogonaux demandé (avec l'hypothèse que le nombre de faisceau est une puissance de 2). Néanmoins, la matrice de Butler a un problème de conception majeur. Ce problème réside dans la structure de la matrice qui renferme des croisements ce qui a été adressé par différents travaux de recherches dans la littérature. Les Guide Intégré au Substrat (GIS) offrent des caractéristiques intéressants pour la conception des composants microondes et millimétriques faciles à intégrer sur un même support avec d'autres composants planaires. Les composants à base de GIS combinent les avantages des guides d'ondes rectangulaires, comme leur grand facteur de qualité Q, leur faibles pertes tout en étant compatible avec les technologies à faibles coûts comme le PCB et le LTCC. Vus ses caractéristiques attrayants, la technologie GIS devient un bon candidat pour la réalisation des matrices multifaisceaux faciles à intégrer avec d'autres systèmes en technologies planaires ou à base de guide GIS. Dans cette thèse, de nouveaux composants passifs sont développés en exploitant la technologie GIS en multicouches en vue de la réalisation d'une matrice de Butler 4x4 compacte et large bande. Les composants recherchés sont donc des coupleurs et des déphaseurs ayant des performances large bande en termes des amplitudes des coefficients de transmissions et les phases associés tout en gardant de faibles niveaux de pertes et de bonnes isolations. Différents techniques pour l'implémentation de déphaseurs large bande en technologie GIS sont présentés. Une nouvelle structure à base d'une propagation composite : main gauche main droite (Composite Right/Left- Handed, CRLH) dans un guide d'onde est proposée. La structure consiste d'un guide d'onde monocouche ayant des fenêtres inductives et des fentes transversales à réactances capacitives pour synthétiser l'inductance parallèle et la capacité série main gauche, respectivement. La structure est adaptée pour les réalisations de déphaseurs compacts en technologie GIS. Bien que les pertes d'insertions restent dans le même ordre de grandeur de celles des structures CRLH à base d'éléments non-localisés, ces niveaux de pertes restent relativement grands par rapport aux applications nécessitant plusieurs déphaseurs. Les déphaseurs à bases de GIS ayant des longueurs égales et des largeurs variables sont ensuite abordés. Ce type de déphaseur est effectivement très adapté à la technologie GIS qui permet des réalisations de parcours avec différentes formes (parcours droits, courbés, coudés, ..) tout en assurant des différences de phase large bande. Afin de satisfaire de faibles pertes d'insertions pour une large dynamique de phase, la longueur de ces déphaseurs est en compromis avec les variations progressives des différentes largeurs associées aux valeurs de déphasages requises. Une transition large bande, double couche et à faible perte est ainsi proposée. La transition est analysée à partir de son circuit électrique équivalent afin d'étudier les performances en termes de l'amplitude et la phase du coefficient de transmission par rapport aux différents paramètres structurels de la transition. Cette transition est ensuite exploitée pour développer un déphaseur à trois couches, large bande, en GIS. La structure consiste effectivement d'un guide d'onde replié à plusieurs reprises sur luimême selon la longueur dans une topologie trois couches à faibles pertes. De nouveaux coupleurs double couche en GIS sont également proposés. Pour les applications BFNs, une structure originale d'un coupleur large bande est développée. La structure consiste de deux guides d'onde parallèles qui partagent leur grand mur ayant une paire de fentes inclinées et décalées par rapport au centre de la structure. Une étude paramétrique détaillée est faite pour étudier l'impact des différents paramètres des fentes sur l'amplitude et la phase du coefficient de transmission. Le coupleur proposé a l'avantage d'assurer une large dynamique de couplage ayant des performances larges bandes en termes des amplitudes et les phases des coefficients de transmission avec de faibles pertes et de bonnes isolations entre le port d'entré et celui isolé. D'autre part, contrairement à d'autres travaux antérieurs et récents qui souffraient d'une corrélation directe entre la phase en transmission et le niveau de couplage, la structure proposée permet de contrôler le niveau de couplage en maintenant presque les mêmes valeurs de phase en transmission pour différents niveaux de couplage. Ceci le rend un bon candidat pour les BFNs déployant différents coupleurs telle la matrice de Nolen. Une deuxième structure originale d’un coupleur bibande est également proposée. La structure consiste de deux coupleurs concentriques en guide nervuré intégré au substrat avec un motif innovant de démultiplexage à base de GIS. Ce coupleur a été développé conjointement avec M. Tarek Djerafi de l’Ecole Polytechnique de Montréal dans un cadre de collaboration avec le Prof. Ke Wu. Finalement, pour l'implémentation de la matrice de Butler, la topologie double couche est explorée à deux niveaux. Le premier consiste à optimiser les caractéristiques électriques de la matrice, tandis que le second concerne l'optimisation de la surface occupée afin de rendre la matrice la plus compacte possible sans dégrader ses performances électriques. D'une part, la structure double couche présente une solution intrinsèque au problème de croisement permettant ainsi une plus grande flexibilité pour la compensation de phase sur une large bande de fréquence. Ceci est réalisé par une conception adéquate de la surface géométrique sur chaque couche de substrat et optimiser les différentes sections de GIS avec les différents parcours adoptés. La deuxième étape consiste effectivement à optimiser la surface sur chaque couche en profitant de la technologie GIS. Ceci consiste à réaliser des murs latéraux communs entre différents chemin électrique de la matrice en vue d'une compacité optimale. Les deux prototypes de matrices de Butler 4x4 sont optimisés, fabriqués et mesurés. Les résultats de mesures sont en bon accord avec ceux de la simulation. Des niveaux d'isolations mieux que - 15 dB avec des niveaux de réflexions inférieurs à -12 dB sont validés expérimentalement sur plus de 24% de bande autour de 12.5 GHz. Les coefficients de transmission montrent de faibles dispersions d'environ 1 dB avec une moyenne de -6.8 dB, et 10° par rapport aux valeurs théoriques, respectivement, sur toute la bande de fréquence. ABSTRACT : Multibeam antennas have become a key element in nowadays wireless communication systems where increased channel capacity, improved transmission quality with minimum interference and multipath phenomena are severe design constraints. These antennas are classified in two main categories namely adaptive smart antennas and switched-beam antennas. Switched-beam antennas consist of an elementary antenna array connected to a Multiple Beam Forming Network (M-BFN). Among the different M-BFNs, the Butler matrix has received particular attention as it is theoretically lossless and employs the minimum number of components to generate a given set of orthogonal beams (provided that the number of beams is a power of 2). However, the Butler matrix has a main design problem which is the presence of path crossings that has been previously addressed in different research works. Substrate Integrated Waveguide (SIW) features interesting characteristics for the design of microwave and millimetre-wave integrated circuits. SIW based components combine the advantages of the rectangular waveguide, such as the high Q factor (low insertion loss) and high power capability while being compatible with low-cost PCB and LTCC technologies. Owing to its attractive features, the use of SIW technology appears as a good candidate for the implementation of BFNs. The resulting structure is therefore suitable for both waveguide-like and planar structures. In this thesis, different novel passive components (couplers and phase shifters) have been developed exploring the multi-layer SIW technology towards the implementation of a two-layer compact 4×4 Butler matrix offering wideband performances for both transmission magnitudes and phases with good isolation and input reflection characteristics. Different techniques for the implementation of wideband fixed phase shifters in SIW technology are presented. First, a novel waveguide-based CRLH structure is proposed. The structure is based on a single-layer waveguide with shunt inductive windows (irises) and series transverse capacitive slots, suitable for SIW implementations for compact phase shifters. The structure suffers relatively large insertion loss which remains however within the typical range of non-lumped elements based CRLH implementations. Second, the well-known equal length, unequal width SIW phase shifters is discussed. These phase shifters are very adapted for SIW implementations as they fully exploit the flexibility of the SIW technology in different path shapes while offering wideband phase characteristics. To satisfy good return loss characteristics with this type of phase shifters, the length has to be compromised with respect to the progressive width variations associated with the required phase shift values. A twolayer, wideband low-loss SIW transition is then proposed. The transition is analyzed using its equivalent circuit model bringing a deeper understanding of its transmission characteristics for both amplitude and phase providing therefore the basic guidelines for electromagnetic optimization. Based on its equivalent circuit model, the transition can be optimized within the well equal-length SIW phase shifters in order to compensate its additional phase shift within the frequency band of interest. This twolayer wideband phase shifter scheme has been adopted in the final developed matrix architecture.This transition is then exploited to develop a three-layer, multiply-folded waveguide structure as a good candidate for compensated-length, variable width, low-loss, compact wideband phase shifters in SIW technology. Novel two-layer SIW couplers are also addressed. For BFNs applications, an original structure for a two-layer 90° broadband coupler is developed. The proposed coupler consists of two parallel waveguides coupled together by means of two parallel inclined-offset resonant slots in their common broad wall. A complete parametric study of the coupler is carried out including the effect of the slot length, inclination angle and offset on both the coupling level and the transmission phase. The first advantage of the proposed coupler is providing a wide coupling dynamic range by varying the slot parameters allowing the design of wideband SIW Butler matrix in two-layer topology. In addition, previously published SIW couplers suffer from direct correlation between the transmission phase and the coupling level, while the coupler, hereby proposed, allows controlling the transmission phase without significantly affecting the coupling level, making it a good candidate for BFNs employing different couplers, such as, the Nolen matrix. A novel dual-band hybrid ring coupler is also developed in multi-layer Ridged SIW (RSIW) technology. This coupler has been jointly developed with Tarek Djerafi in a collaboration scenario with Prof. Ke Wu from the Ecole Polytechnique de Montréal. The coupler has an original structure based on two concentric rings in RSIW topology with the outer ring periodically loaded with radial, stub-loaded transverse slots. A design procedure is presented based on the Transverse Resonance Method (TRM) of the ridged waveguide together with the simple design rules of the hybrid ring coupler. A C/K dual band coupler with bandwidths of 8.5% and 14.6% centered at 7.2 GHz and 20.5 GHz, respectively, is presented. The coupler provides independent dual band operation with low-dispersive wideband operation. Finally, for the Butler matrix design, the two-layer SIW implementation is explored through a two-fold enhancement approach for both the matrix electrical and physical characteristics. On the one hand, the two-layer topology allows an inherent solution for the crossing problem allowing therefore more flexibility for phase compensation over a wide frequency band. This is achieved by proper geometrical optimization of the surface on each layer and exploiting the SIW technology in the realization of variable width waveguides sections with the corresponding SIW bends. On the other hand, the two-layer SIW technology is exploited for an optimized space saving design by implementing common SIW lateral walls for the matrix adjacent components seeking maximum size reduction. The two corresponding 4×4 Butler matrix prototypes are optimized, fabricated and measured. Measured results are in good agreement with the simulated ones. Isolation characteristics better than -15 dB with input reflection levels lower than -12 dB are experimentally validated over 24% frequency bandwidth centered at 12.5 GHz. Measured transmission magnitudes and phases exhibit good dispersive characteristics of 1dB, around an average value of -6.8 dB, and 10° with respect to the theoretical phase values, respectively, over the entire frequency band

Impedance Transformers

Non

Low-Cost Integrated Waveguide Antenna Front-End Solutions for Fifth Generation Cellular Systems and Beyond

RÉSUMÉ : À ondes millimétriques (ou simplement mm - ondes) réseaux d'antennes avec un seul polarisation linéaire (LP ) , double polarisation linéaire ( DLP ) et double polarisation circulaire ( DCP) caractéristiques sont largement utilisés pour de nombreuses applications , il y compris la communication de données sans fil , capteurs radar , passive imagerie , la récupération d'énergie et les systèmes de radiocommunication cognitifs . Parmi les différents types de structure d'alimentation , guide d'ondes présente un excellent candidat pour mettre en oeuvre des réseaux d'alimentation à faible perte et gain élevé réseaux d'antennes sur la plage de fréquence à ondes millimétriques . Ces antennes à base de guide d'ondes - ont été présentant d'excellentes caractéristiques de rayonnement , mais ils ne sont pas faciles à intégrer avec des composants actifs . A la fréquence à ondes millimétriques , SIW ( substrat de guide d'ondes intégré ) est un candidat exceptionnel émergents à mettre en oeuvre une faible perte et des réseaux d'alimentation à faible coût. Antenne SIW - alimenté est capable de produire l'efficacité de rayonnement à haute et le comportement d'impédance à large bande . Dans cette thèse , la technologie de transmission alimentation SIW est choisi pour mettre en oeuvre des réseaux électriques et de phase de distribution pour réaliser une grande efficacité antenne extrémités avant. Les principales contributions scientifiques et techniques peuvent être résumées en deux parties .Dans la première partie , des solutions pour les ouvertures rayonnantes efficacement ont été proposés tels que gain élevé réseaux d'antennes LP , DLP réseaux d'antennes et DCP réseaux d'antennes . Le choix de l'élément rayonnant avec d'excellentes caractéristiques de rayonnement est vital dans la réalisation de gain élevé réseau d'antennes et réseaux phasés, électroniquement orientables . Dans la deuxième partie , de nouvelles techniques ont été proposées pour diriger le faisceau fixe dans des directions multiples en élévation et azimut en utilisant le réseau de décalage de phase passive.----------ABSTRACT Millimeter-wave (or simply mm-wave) antenna arrays with single linear polarization (LP), dual linear polarization (DLP) and dual circular polarization (DCP) characteristics are widely being used for numerous applications including wireless data communication, radar sensors, passive imaging, energy harvesting and cognitive radio systems. Among different types of feeding structure, waveguide presents an excellent candidate to implement low-loss feeding networks and high-gain antenna arrays over mm-wave frequency range. Those waveguide-based antennas have been exhibiting excellent radiation characteristics, but they are not easy to integrate with active components. At mm-wave frequency, SIW (substrate integrated waveguide) is an emerging outstanding candidate to implement low loss and low cost feeding networks. SIW-fed antenna is able to yield high radiation efficiency and broadband impedance behavior. In this thesis, SIW feeding transmission technology is chosen to implement power and phase distributing networks for realizing high efficiency antenna front ends. The main scientific and technical contributions can be summarized into two parts. In the first part, solutions for efficiently radiating apertures have been proposed such as high gain LP antenna arrays, DLP antenna arrays and DCP antenna arrays. The radiating element choice with excellent radiation characteristics is vital in realising high gain antenna array and electronically steerable phased arrays. In the second part, new techniques have been proposed to steer the fixed beam into multiple directions in elevation and azimuth utilizing passive phase shifting network. At 60 GHz frequency, dielectric rod antenna is selected for linearly polarized radiation and cavity backed metallic circular patch antenna is selected to obtain circular polarization radiation. Single rod antenna element is experimentally characterized to validate the proposed concept. In the next stage, high gain antenna array with 45o linear polarization utilizing rod antenna radiating element is demonstrated and feeding implemented in three dimensional (3-D) architecture is integrated along with the 4 x 4 antenna array. The data handling capability of single polarization antenna array is increased up to two fold by integrating two orthogonal polarized antenna arrays with an aperture area of one single polarized array

Design and analysis of wideband passive microwave devices using planar structures

A selected volume of work consisting of 84 published journal papers is presented to demonstrate the contributions made by the author in the last seven years of his work at the University of Queensland in the area of Microwave Engineering. The over-arching theme in the author’s works included in this volume is the engineering of novel passive microwave devices that are key components in the building of any microwave system. The author’s contribution covers innovative designs, design methods and analyses for the following key devices and associated systems: Wideband antennas and associated systems Band-notched and multiband antennas Directional couplers and associated systems Power dividers and associated systems Microwave filters Phase shifters Much of the motivation for the work arose from the desire to contribute to the engineering o

DESIGN AND ANALYSIS OF ANTENNA-ON-CHIP AND ANTENNA-IN-PACKAGE FOR 60-GHZ WIRELESS COMMUNICATIONS

Ph.DDOCTOR OF PHILOSOPH

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance