A radiation-hard dual-channel 12-bit 40 MS/s ADC prototype for the ATLAS liquid argon calorimeter readout electronics upgrade at the CERN LHC

The readout electronics upgrade for the ATLAS Liquid Argon Calorimeters at the CERN Large Hadron Collider requires a radiation-hard ADC. The design of a radiation-hard dual-channel 12-bit 40 MS/s pipeline ADC for this use is presented. The design consists of two pipeline A/D channels each with four Multiplying Digital-to-Analog Converters followed by 8-bit Successive-Approximation-Register analog-to-digital converters. The custom design, fabricated in a commercial 130 nm CMOS process, shows a performance of 67.9 dB SNDR at 10 MHz for a single channel at 40 MS/s, with a latency of 87.5 ns (to first bit read out), while its total power consumption is 50 mW/channel. The chip uses two power supply voltages: 1.2 and 2.5 V. The sensitivity to single event effects during irradiation is measured and determined to meet the system requirements

Fully-photonic digital radio over fibre for future super-broadband access network applications

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel UniversityIn this thesis a Fully-Photonic DRoF (FP-DRoF) system is proposed for deploying of future super-broadband access networks. Digital Radio over Fibre (DRoF) is more independent of the fibre network impairments and the length of fibre than the ARoF link. In order for fully optical deployment of the signal conversion techniques in the FP-DRoF architecture, two key components an Analogue-to-Digital Converter (ADC) and a Digital-to-Analogue Converter (DAC)) for data conversion are designed and their performance are investigated whereas the physical functionality is evaluated. The system simulation results of the proposed pipelined Photonic ADC (PADC) show that the PADC has 10 GHz bandwidth around 60 GHz of sampling rate. Furthermore, by changing the bandwidth of the optical bandpass filter, switching to another band of sampling frequency provides optimised performance condition of the PADC. The PADC has low changes on the Effective Number of Bit (ENOB) response versus analogue RF input from 1 GHz up to 22 GHz for 60 GHz sampling frequency. The proposed 8-Bit pipelined PADC performance in terms of ENOB is evaluated at 60 Gigasample/s which is about 4.1. Recently, different methods have been reported by researchers to implement Photonic DACs (PDACs), but their aim was to convert digital electrical signals to the corresponding analogue signal by assisting the optical techniques. In this thesis, a Binary Weighted PDAC (BW-PDAC) is proposed. In this BW-PDAC, optical digital signals are fully optically converted to an analogue signal. The spurious free dynamic range at the output of the PDAC in a back-to-back deployment of the PADC and the PDAC was 26.6 dBc. For further improvement in the system performance, a 3R (Retiming, Reshaping and Reamplifying) regeneration system is proposed in this thesis. Simulation results show that for an ultrashort RZ pulse with a 5% duty cycle at 65 Gbit/s using the proposed 3R regeneration system on a link reduces rms timing jitter by 90% while the regenerated pulse eye opening height is improved by 65%. Finally, in this thesis the proposed FP-DRoF functionality is evaluated whereas its performance is investigated through a dedicated and shared fibre links. The simulation results show (in the case of low level signal to noise ratio, in comparison with ARoF through a dedicated fibre link) that the FP-DRoF has better BER performance than the ARoF in the order of 10-20. Furthermore, in order to realize a BER about 10-25 for the ARoF, the power penalty is about 4 dBm higher than the FP-DRoF link. The simulation results demonstrate that by considering 0.2 dB/km attenuation of a standard single mode fibre, the dedicated fibre length for the FP-DRoF link can be increased to about 20 km more than the ARoF link. Moreover, for performance assessment of the proposed FP-DRoF in a shared fibre link, the BER of the FP-DRoF link is about 10-10 magnitude less than the ARoF link for -19 dBm launched power into the fibre and the power penalty of the ARoF system is 10 dBm more than the FP-DRoF link. It is significant to increase the fibre link’s length of the FP-DRoF access network using common infrastructure. In addition, the simulation results are demonstrated that the FP-DRoF with non-uniform Wavelength Division Multiplexing (WDM) is more robust against four wave mixing impairment than the conventional WDM technique with uniform wavelength allocation and has better performance in terms of BER. It is clearly verified that the lunched power penalty at CS for DRoF link with uniform WDM techniques is about 2 dB higher than non-uniform WDM technique. Furthermore, uniform WDM method requires more bandwidth than non-uniform scheme which depends on the total number of channels and channels spacing

An energy efficient sub-threshold baseband processor architecture for pulsed ultra-wideband communications

Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2006.Includes bibliographical references (p. 79-83).Ultra-wideband (UWB) communications is currently being explored as a medium for high-data-rate last-meter wireless links. Accordingly, there has been much interest in integrating UWB radios onto battery-operated devices, creating a strong demand for energy efficient UWB systems. The objective of this work is to describe how operating the digital baseband processor in the sub-threshold region and increasing the degree of parallelism can translate into energy savings across the entire UWB receiver. While sub-threshold operation is traditionally used for low energy, low performance applications such as wrist-watches, this work examines how sub-threshold operation can be applied to low energy, high performance applications. Simulation results for a 100-Mbps UWB baseband processor using the digital logic cell library of a 90-nm process are presented.by Vivienne Sze.S.M

A 1.8-pJ/b, 12.5-25-Gb/s wide range all-digital clock and data recovery circuit

Recently, there has been a strong drive to replace established analog circuits for multi-gigabit clock and data recovery (CDR) by more digital solutions. We focused on phase locked loop-based all-digital CDR (AD-CDR) techniques which contain a digital loop filter (DLF) and a digital controlled oscillator (DCO) and pushed the digital integration up to a level where our DLF is entirely synthesized. To enable this, we found that extensive subsampling can be used to decrease the speed of the DLF while maintaining a good operation. Additionally, an Inverse Alexander phase detector and a 5.5-bit resolution DCO complete the AD-CDR architecture. As a result of the low complexity and digital architecture, the AD-CDR occupies a compact active chip area of 0.050 mm(2) and consumes only 46 mW at 25 Gb/s. This is the smallest area and the lowest power consumption compared with the state-of-the-art. In addition, our implementation is highly tunable due to the synthesized logic, and supports a wide operating range (12.5-25 Gb/s), which is a significantly larger range compared with the previous work. Finally, thanks to our digital architecture, the power dissipation decreases linearly while moving to the lower speeds of our operating range. This is in contrast with the most prior work, making our design truly adaptive

The Design of Low Power Ultra-Wideband Transceiver

Ph.DDOCTOR OF PHILOSOPH

High Speed Reconfigurable NRZ/PAM4 Transceiver Design Techniques

While the majority of wireline standards use simple binary non-return-to-zero (NRZ) signaling, four-level pulse-amplitude modulation (PAM4) standards are emerging to increase bandwidth density. This dissertation proposes efficient implementations for high speed NRZ/PAM4 transceivers. The first prototype includes a dual-mode NRZ/PAM4 serial I/O transmitter which can support both modulations with minimum power and hardware overhead. A source-series-terminated (SST) transmitter achieves 1.2Vpp output swing and employs lookup table (LUT) control of a 31-segment output digital-to-analog converter (DAC) to implement 4/2-tap feed-forward equalization (FFE) in NRZ/PAM4 modes, respectively. Transmitter power is improved with low-overhead analog impedance control in the DAC cells and a quarter-rate serializer based on a tri-state inverter-based mux with dynamic pre-driver gates. The transmitter is designed to work with a receiver that implements an NRZ/PAM4 decision feedback equalizer (DFE) that employs 1 finite impulse response (FIR) and 2 infinite impulse response (IIR) taps for first post-cursor and long-tail ISI cancellation, respectively. Fabricated in GP 65-nm CMOS, the transmitter occupies 0.060mm² area and achieves 16Gb/s NRZ and 32Gb/s PAM4 operation at 10.4 and 4.9 mW/Gb/s while operating over channels with 27.6 and 13.5dB loss at Nyquist, respectively. The second prototype presents a 56Gb/s four-level pulse amplitude modulation (PAM4) quarter-rate wireline receiver which is implemented in a 65nm CMOS process. The frontend utilize a single stage continuous time linear equalizer (CTLE) to boost the main cursor and relax the pre-cursor cancelation requirement, requiring only a 2-tap pre-cursor feed-forward equalization (FFE) on the transmitter side. A 2-tap decision feedback equalizer (DFE) with one finite impulse response (FIR) tap and one infinite impulse response (IIR) tap is employed to cancel first post-cursor and longtail inter-symbol interference (ISI). The FIR tap direct feedback is implemented inside the CML slicers to relax the critical timing of DFE and maximize the achievable data-rate. In addition to the per-slice main 3 data samplers, an error sampler is utilized for background threshold control and an edge-based sampler performs both PLL-based CDR phase detection and generates information for background DFE tap adaptation. The receiver consumes 4.63mW/Gb/s and compensates for up to 20.8dB loss when operated with a 2- tap FFE transmitter. The experimental results and comparison with state-of-the-art shows superior power efficiency of the presented prototypes for similar data-rate and channel loss. The usage of proposed design techniques are not limited to these specific prototypes and can be applied for any wireline transceiver with different modulation, data-rate and CMOS technology

Low-power ADC designs in scaled CMOS process

This thesis presents advanced design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs), continuous-time ∆Σ ADCs, and single-slope (SS) ADCs in nano-scale CMOS technologies. (1) In high-speed SAR ADCs, metastability of the comparator limits the performance, which even results in the sparkle code errors. Proposed background calibration utilizing the comparator decision time detector removes the metastability-induced sparkle code errors by controlling the metastability detection window. At the same time, 1-bit resolution increase is gained from the proposed technique, which results in the fewer comparison cycles. Along with the relaxed requirement on the comparator, this cycle reduction helps to achieve the good power efficiency in high-speed SAR design. A prototype ADC in 40nm CMOS achieves 35.3dB SNDR and consumes 0.81mW while sampling at 700MS/s. (2) In the proposed continuous-time ∆Σ ADCs, conventional power-hungry opamp is replaced by voltage controlled oscillators (VCOs) that perform the data conversion in the phase domain instead of the voltage domain. In contrary to the opamp which is difficult to achieve good performance in the advanced CMOS process, VCOs have many advantages in the phase domain. To solve the nonlinear gain of VCOs, dual VCO-based integrator is used to suppress the dominant second-order distortion. To address the distortion from the DAC, a novel DAC calibration technique that both digitally senses and removes DAC mismatch errors is proposed. It has low hardware complexity by taking advantage of the intrinsic clocked level averaging (CLA) capability of dual-VCO-based integrator. It ensures high linearity regardless of the VCO center frequency. By lowering the VCO center frequency, power consumption is reduced. A prototype ADC designed in 130nm occupies an area of only 0.04mm² . It achieves 71dB SNDR over 1.7MHz bandwidth (BW) while sampling at 250MS/s and consuming only 0.9mW from a 1.2V power supply. The corresponding figure-of-merit (FOM) is 98 fJ/conversion-step. (3) A SS ADC has advantages of high linearity and a simple architecture. Thus, it is well suited for the column-parallel architecture for the CMOS image sensors. However, conversion speed is severely limited in high-bit resolution since more than 2 [superscript N] cycles are required for a N-bit resolution. To tackle this limitation, a two-step approach becomes popular. In this thesis, a two-step SAR/SS architecture is presented. In addition to reducing the conversion time, analog correlated double sampling (CDS) can cancel kT/C noise, which enables capacitor area reduction. A prototype ADC in 180nm CMOS occupies only 9.3µm x 830µm. It achieves 60.5dB SNR after CDS while sampling at 256kHz and consuming 91µWElectrical and Computer Engineerin

Digital ADCs and ultra-wideband RF circuits for energy constrained wireless applications by Denis Clarke Daly.

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.Cataloged from PDF version of thesis.Includes bibliographical references (p. 173-183).Ongoing advances in semiconductor technology have enabled a multitude of portable, low power devices like cellular phones and wireless sensors. Most recently, as transistor device geometries reach the nanometer scale, transistor characteristics have changed so dramatically that many traditional circuits and architectures are no longer optimal and/or feasible. As a solution, much research has focused on developing 'highly digital' circuits and architectures that are tolerant of the increased leakage, variation and degraded voltage headrooms associated with advanced CMOS processes. This thesis presents several highly digital, mixed-signal circuits and architectures designed for energy constrained wireless applications. First, as a case study, a highly digital, voltage scalable flash ADC is presented. The flash ADC, implemented in 0.18 [mu]m CMOS, leverages redundancy and calibration to achieve robust operation at supply voltages from 0.2 V to 0.9 V. Next, the thesis expands in scope to describe a pulsed, noncoherent ultra-wideband transceiver chipset, implemented in 90 nm CMOS and operating in the 3-to-5 GHz band. The all-digital transmitter employs capacitive combining and pulse shaping in the power amplifier to meet the FCC spectral mask without any off-chip filters. The noncoherent receiver system-on-chip achieves both energy efficiency and high performance by employing simple amplifier and ADC structures combined with extensive digital calibration. Finally, the transceiver chipset is integrated in a complete system for wireless insect flight control.(cont.) Through the use of a flexible PCB and 3D die stacking, the total weight of the electronics is kept to 1 g, within the carrying capacity of an adult Manduca sexta moth. Preliminary wireless flight control of a moth in a wind tunnel is demonstrated.Ph.D

Energy-efficient data converter design in scaled CMOS technology

Data converters bridge the physical and digital worlds. They have been the crucial building blocks in modern electronic systems, and are expected to have a growing significance in the booming era of Internet-of-Things (IoT) and 5G communications. The applications raise energy-efficiency requirements for both low-speed and high-speed converters since they are widely deployed in wireless sensor nodes and portable devices. To explore the solutions, the author worked on three directions: 1) techniques to improve the efficiency of the low-speed converters including the comparator; 2) techniques to develop high-speed data converters including the reference stabilization; 3) new architecture to improve the efficiency of the capacitance-to-digital converter (CDC). In the first part, a power-efficient 10-bit SAR ADC featured with a gain-boosted dynamic comparator is presented. In energy-constrained applications, the converter is usually supplied with low supply voltage (e.g., 0.3 V-0.5 V), which reduces the comparator pre-amplifier (pre-amp) gain and results in higher noise. A novel comparator topology with a dynamic common-gate stage is proposed to increase the pre-amplification gain, thereby reducing noise and offset. Besides, statistical estimation and loading switching techniques are combined to further improve energy efficiency. A 40-nm CMOS prototype achieves a Walden FoM of 1.5 fJ/conversion-step while operating at 100-kS/s from a 0.5-V supply. To further improve the energy-efficiency of the comparator, a novel dynamic pre-amp is proposed. By using an inverter-based input pair powered by a floating reservoir capacitor, the pre-amp realizes both current reuse and dynamic bias, thereby significantly boosting g [subscript m] /I [subscript D] and reducing noise. Moreover, it greatly reduces the influence of the input common-mode (CM) voltage on the comparator performance, including noise, offset, and delay. A prototype comparator in 180-nm achieves 46-μV input-referred noise while consuming only 1 pJ per comparison under 1.2-V supply, which represents greater than 7 times energy efficiency boost compared to that of a Strong-Arm (SA) latch. The second part of this dissertation focuses on high-speed data converter techniques. A 10-bit high-speed two-stage loop-unrolled SAR ADC is presented. To reduce the SAR logic delay and power, each bit uses a dedicated comparator to store its output and generate an asynchronous clock for the next comparison. To suppress the comparator offset mismatch induced non-linearity, a shared pre-amp are employed in the second fine stage, which is implemented by a dynamic latch to avoid static power consumption. The prototype ADC in 40-nm CMOS achieves 55-dB peak SNDR at 200-MS/s sampling rate without any calibration. A key limiting factor for the SAR ADC to simultaneously achieve high speed and high resolution is the reference ripple settling problem caused by DAC switching. Unlike prior techniques that aim to minimize the reference ripple which requires large reference buffer power or on-chip decoupling capacitance area, this work proposes a new perspective: it provides an extra path for the full-sized reference ripple to couple to the comparator but with an opposite polarity, so that the effect of the reference ripple is canceled out, thus ensuring an accurate conversion result. The prototype 10-bit 120-MS/s SAR ADC is fabricated in 40-nm CMOS process and achieves an SNDR of 55 dB with only 3 pF reference decoupling capacitor. Finally, this dissertation also presents the design of an incremental time-domain two-step CDC. Unlike the classic two-step CDC, this work replaces the OTA-based active-RC integrator with a VCO-based integrator and performs time domain (TD) ΔΣ modulation. The VCO is mostly digital and consumes low power. Featuring the infinite DC gain in phase domain and intrinsic spatial phase quantization, this TDΔΣ enables a CDC design, achieving 85-dB SQNR by having only a 4-bit quantizer, a 1st-order loop and a low OSR of 15. The prototype fabricated in 40-nm CMOS achieves a resolution of 0.29 fF while dissipating only 0.083 nJ per conversion, which improves the energy efficiency by greater than 2 times comparing to that of state-of-the-art CDCsElectrical and Computer Engineerin