An Ultra-Wideband Low Noise Amplifier and Spectrum Sensing Technique for Cognitive Radio

A low power ultra-wideband, inductorless low noise amplifier (LNA) employing a noise cancellation architecture and designed in a commercially available 40nm 1.2V digital CMOS process is presented. The amplifier targets cognitive radio communication applications which cover the frequency range of 1-10 GHz and achieves an S11 \u3c -9.5 dB from 1.4 - 9.5 GHz. Within this bandwidth the maximum power gain is 13.4 dB, the maximum noise figure is 4.3 dB, and the miminum IIP3 is 0 dBm. The total power consumption of the LNA (neglecting the buffer required to drive the 50 Ω test equipment) is 8 mW. The total area consumed is 0.031mm2 excluding the pads. A spectrum sensing technique using translational loop technique is also proposed to realize simultaneous spectrum sensing and data reception of cognitive radio. This technique also eliminates the need for tunable sharp band-select filter at the front-end

Forward Body Biased Low Power 4.0-10.6 GHz Wideband Low Noise Amplifier

A forward body biased low power Low Noise Amplifier (LNA) is designed using Common Gate (CG) topology. By using current reuse technique between the first stage and second stage Common Source topology accompanied with forward body biasing leads to low power dissipation. A series to parallel tank circuit at this stage leads to wideband design. A shunt peaking inductor at the drain terminal of second stage causes the higher frequency peak to increase leading to wide bandwidth. Two CS cascade stages are used to increase the overall gain of the proposed LNA with a buffer stage at the output for output matching. The proposed LNA attained maximum gain of 26.39 dB with a gain greater than 16 dB over entire range. The circuit gives reflection coefficient less than – 10 dB with NF 2.7 dB. With Vdd of 0.925 V, a DC current of 8.32 mA is consumed giving 7.7 mW power consumption

A Novel High Linearity and Low Power Folded CMOS LNA for UWB Receivers

© 2017 World Scientific Publishing Company. Electronic version of an article published as Journal of Circuits, Systems and Computers, Vol. 27, No. 03, 1850047, https://doi.org/10.1142/S0218126618500470.This paper presents a high linearity and low power Low-Noise Amplifier (LNA) for Ultra-Wideband (UWB) receivers based on CHRT 0.18μm CMOS technology. In this work, the folded topology is adopted in order to reduce the supply voltage and power consumption. Moreover, a band-pass LC filter is embedded in the folded-cascode circuit to extend bandwidth. The transconductance nonlinearity has a great impact on the whole LNA linearity performance under a low supply voltage. A post-distortion (PD) technique employing an auxiliary transistor is applied in the transconductance stage to improve the linearity. The post-layout simulation results indicate that the proposed LNA achieves a maximum power gain of 12.8dB. The input and output reflection coefficients both are lower than -10.0dB over 2.5~11.5GHz. The input third-order intercept point (IIP3) is 5.6dBm at 8GHz and the noise figure (NF) is lower than 4.0dB. The LNA consumes 5.4mW power under a 1V supply voltage.Peer reviewe

HIGH LINEARITY UNIVERSAL LNA DESIGNS FOR NEXT GENERATION WIRELESS APPLICATIONS

Design of the next generation (4G) systems is one of the most active and important area of research and development in wireless communications. The 2G and 3G technologies will still co-exist with the 4G for a certain period of time. Other applications such as wireless LAN (Local Area Network) and RFID are also widely used. As a result, there emerges a trend towards integrating multiple wireless functionalities into a single mobile device. Low noise amplifier (LNA), the most critical component of the receiver front-end, determines the sensitivity and noise figure of the receiver and is indispensable for the complete system. To satisfy the need for higher performance and diversity of wireless communication systems, three LNAs with different structures and techniques are proposed in the thesis based on the 4G applications. The first LNA is designed and optimized specifically for LTE applications, which could be easily added to the existing system to support different standards. In this cascode LNA, the nonlinearity coming from the common source (CS) and common gate (CG) stages are analyzed in detail, and a novel linear structure is proposed to enhance the linearity in a relatively wide bandwidth. The LNA has a bandwidth of 900MHz with the linearity of greater than 7.5dBm at the central frequency of 1.2GHz. Testing results show that the proposed structure effectively increases and maintains linearity of the LNA in a wide bandwidth. However, a broadband LNA that covers multiple frequency ranges appears more attractive due to system simplicity and low cost. The second design, a wideband LNA, is proposed to cover multiple wireless standards, such as LTE, RFID, GSM, and CDMA. A novel input-matching network is proposed to relax the tradeoff among noise figure and bandwidth. A high gain (>10dB) in a wide frequency range (1-3GHz) and a minimum NF of 2.5dB are achieved. The LNA consumes only 7mW on a 1.2V supply. The first and second LNAs are designed mainly for the LTE standard because it is the most widely used standard in the 4G communication systems. However, WiMAX, another 4G standard, is also being widely used in many applications. The third design targets on covering both the LTE and the WiMAX. An improved noise cancelling technique with gain enhancing structure is proposed in this design and the bandwidth is enlarged to 8GHz. In this frequency range, a maximum power gain of 14.5dB and a NF of 2.6-4.3dB are achieved. The core area of this LNA is 0.46x0.67mm2 and it consumes 17mW from a 1.2V supply. The three designs in the thesis work are proposed for the multi-standard applications based on the realization of the 4G technologies. The performance tradeoff among noise, linearity, and broadband impedance matching are explored and three new techniques are proposed for the tradeoff relaxation. The measurement results indicate the techniques effectively extend the bandwidth and suppress the increase of the NF and nonlinearity at high frequencies. The three proposed structures can be easily applied to the wideband and multi-standard LNA design

Analysis and Design of Wideband Low Noise Amplifier with Digital Control

The design issues in designing low noise amplifier (LNA) for Software-Defined-Radio (SDR) are reviewed. An inductor-less wideband low noise amplifier aiming at low frequency band (0.2-2GHz) for Software-Defined-Radio is presented. Shunt-shunt LNA with active feedback is used as the first stage which is carefully optimized for low noise and wide band applications. A digitally controlled second stage is employed to provide an additional 12dB gain control. A novel method is proposed to bypass the first stage without degrading input matching. This LNA is fabricated in a standard 0.18 um CMOS technology. The measurement result shows the proposed LNA has a gain range of 6dB-18dB at high gain mode and -12dB-0dB at low gain mode, as well as a –3dB bandwidth of 2GHz. The noise figure (NF) is 3.5-4.5dB in the high gain setting mode. It consumes 20mW from a 1.8V supply

An Ultra-wideband Low-power Low-noise Amplifier Linearized by Adjusted Derivative Superposition and Feedback Techniques

Ultra-wideband (UWB) applications require low-power and low-noise amplifiers (LNAs) that can operate over a wide frequency range. However, conventional LNAs often suffer from poor linearity and high-power consumption. This research work proposes a novel LNA design that uses the adjusted derivative superposition (DS) technique and feedback to improve the linearity and reduce the power consumption of UWB LNAs. The DS technique enhances the third-order intermodulation (IM3) cancellation by adjusting the bias currents of the transistors, whereas the feedback improves the stability and input matching of the LNA. The LNA is implemented using a degenerated common source topology in a 180 nm standard CMOS technology. The simulation results show that the LNA achieves a power gain of 10–12.2 dB, an input third-order intercept point (IIP3) of about 12 dBm, and a noise figure of less than 2.5 dB over the UWB frequency band of 3.1–10.6 GHz. The input reflection coefficient is less than -10 dB, and the power consumption is 11.6 mW with a 1.5 V power supply. The designed LNA offers a novel and innovative solution for UWB applications that significantly improve the performance and efficiency of UWB LNAs whereas reducing the cost and complexity of implementation

High Performance RF and Basdband Analog-to-Digital Interface for Multi-standard/Wideband Applications

The prevalence of wireless standards and the introduction of dynamic standards/applications, such as software-defined radio, necessitate the next generation wireless devices that integrate multiple standards in a single chip-set to support a variety of services. To reduce the cost and area of such multi-standard handheld devices, reconfigurability is desirable, and the hardware should be shared/reused as much as possible. This research proposes several novel circuit topologies that can meet various specifications with minimum cost, which are suited for multi-standard applications. This doctoral study has two separate contributions: 1. The low noise amplifier (LNA) for the RF front-end; and 2. The analog-to-digital converter (ADC). The first part of this dissertation focuses on LNA noise reduction and linearization techniques where two novel LNAs are designed, taped out, and measured. The first LNA, implemented in TSMC (Taiwan Semiconductor Manufacturing Company) 0.35Cm CMOS (Complementary metal-oxide-semiconductor) process, strategically combined an inductor connected at the gate of the cascode transistor and the capacitive cross-coupling to reduce the noise and nonlinearity contributions of the cascode transistors. The proposed technique reduces LNA NF by 0.35 dB at 2.2 GHz and increases its IIP3 and voltage gain by 2.35 dBm and 2dB respectively, without a compromise on power consumption. The second LNA, implemented in UMC (United Microelectronics Corporation) 0.13Cm CMOS process, features a practical linearization technique for high-frequency wideband applications using an active nonlinear resistor, which obtains a robust linearity improvement over process and temperature variations. The proposed linearization method is experimentally demonstrated to improve the IIP3 by 3.5 to 9 dB over a 2.5–10 GHz frequency range. A comparison of measurement results with the prior published state-of-art Ultra-Wideband (UWB) LNAs shows that the proposed linearized UWB LNA achieves excellent linearity with much less power than previously published works. The second part of this dissertation developed a reconfigurable ADC for multistandard receiver and video processors. Typical ADCs are power optimized for only one operating speed, while a reconfigurable ADC can scale its power at different speeds, enabling minimal power consumption over a broad range of sampling rates. A novel ADC architecture is proposed for programming the sampling rate with constant biasing current and single clock. The ADC was designed and fabricated using UMC 90nm CMOS process and featured good power scalability and simplified system design. The programmable speed range covers all the video formats and most of the wireless communication standards, while achieving comparable Figure-of-Merit with customized ADCs at each performance node. Since bias current is kept constant, the reconfigurable ADC is more robust and reliable than the previous published works

Low Noise Amplifier using Darlington Pair At 90nm Technology

The demand of low noise amplifier (LNA) has been rising in today’s communication system. LNA is the basic building circuit of the receiver section satellite. The design concept demonstrates the design trade off with NF, gain, power consumption. This paper reports on with analysis of wideband LNA. This paper shows the schematic of LNA by using Darlington pair amplifier. This LNA has been fabricated on 90nm CMOS process. This paper is focused on to make comparison of three stage and single stage LNA. Here, the phase mismatch between these patameters is quantitavely analyzed to study the effect on gain and noise figure (NF). In this paper, single stage LNA has shown the 23 dB measured gain, while the three stages LNA has demonstrated 29 dB measured gain. Here, LNA designed using darlington pair shows low NF of 3.3-4.8 dB, which comparable to other reported single stage LNA designs and appreciably low compared to the three stages LNA. Hence, findings from this paper suggest the use of single stage LNA designed using Darlington pair in transceiver satellite applications

Survey on individual components for a 5 GHz receiver system using 130 nm CMOS technology

La intención de esta tesis es recopilar información desde un punto de vista general sobre los diferentes tipos de componentes utilizados en un receptor de señales a 5 GHz utilizando tecnología CMOS. Se ha realizado una descripción y análisis de cada uno de los componentes que forman el sistema, destacando diferentes tipos de configuraciones, figuras de mérito y otros parámetros. Se muestra una tabla resumen al final de cada sección, comparando algunos diseños que se han ido presentando a lo largo de los años en conferencias internacionales de la IEEE.The intention of this thesis is to gather information from an overview point about the different types of components used in a 5 GHz receiver using CMOS technology. A review of each of the components that form the system has been made, highlighting different types of configurations, figure of merits and parameters. A summary table is shown at the end of each section, comparing many designs that have been presented over the years at international conferences of the IEEE.Departamento de Ingeniería Energética y FluidomecánicaGrado en Ingeniería en Electrónica Industrial y Automátic