Constrained Phase Noise Estimation in OFDM Using Scattered Pilots Without Decision Feedback

In this paper, we consider an OFDM radio link corrupted by oscillator phase noise in the receiver, namely the problem of estimating and compensating for the impairment. To lessen the computational burden and delay incurred onto the receiver, we estimate phase noise using only scattered pilot subcarriers, i.e., no tentative symbol decisions are used in obtaining and improving the phase noise estimate. In particular, the phase noise estimation problem is posed as an unconstrained optimization problem whose minimizer suffers from the so-called amplitude and phase estimation error. These errors arise due to receiver noise, estimation from limited scattered pilot subcarriers and estimation using a dimensionality reduction model. It is empirically shown that, at high signal-to-noise-ratios, the phase estimation error is small. To reduce the amplitude estimation error, we restrict the minimizer to be drawn from the so-called phase noise geometry set when minimizing the cost function. The resulting optimization problem is a non-convex program. However, using the S-procedure for quadratic equalities, we show that the optimal solution can be obtained by solving the convex dual problem. We also consider a less complex heuristic scheme that achieves the same objective of restricting the minimizer to the phase noise geometry set. Through simulations, we demonstrate improved coded bit-error-rate and phase noise estimation error performance when enforcing the phase noise geometry. For example, at high signal-to-noise-ratios, the probability density function of the phase noise estimation error exhibits thinner tails which results in lower bit-error-rate

TS-MUWSN: Time synchronization for mobile underwater sensor networks

Time synchronization is an important, yet challenging, problem in underwater sensor networks (UWSNs). This challenge can be attributed to: 1) messaging timestamping; 2) node mobility; and 3) Doppler scale effect. To mitigate these problems, we present an acoustic-based time-synchronization algorithm for UWSN, where we compare several message time-stamping algorithms in addition to different Doppler scale estimators. A synchronization system is based on a bidirectional message exchange between a reference node and a slave one, which has to be synchronized. Therefore, we take as reference the DA-Sync-like protocol (Liu et al., 2014), which takes into account node's movement by using first-order kinematic equations, which refine Doppler scale factor estimation accuracy, and result in better synchronization performance. In our study, we propose to modify both time-stamping and Doppler scale estimation procedures. Besides simulation, we also perform real tests in controlled underwater communication in a water test tank and a shallow-water test in the Mediterranean Sea.Peer ReviewedPostprint (author's final draft

mm-Wave Data Transmission and Measurement Techniques: A Holistic Approach

The ever-increasing demand on data services places unprecedented technical requirements on networks capacity. With wireless systems having significant roles in broadband delivery, innovative approaches to their development are imperative. By leveraging new spectral resources available at millimeter-wave (mm-wave) frequencies, future systems can utilize new signal structures and new system architectures in order to achieve long-term sustainable solutions.This thesis proposes the holistic development of efficient and cost-effective techniques and systems which make high-speed data transmission at mm-wave feasible. In this paradigm, system designs, signal processing, and measurement techniques work toward a single goal; to achieve satisfactory system level key performance indicators (KPIs). Two intimately-related objectives are simultaneously addressed: the realization of efficient mm-wave data transmission and the development of measurement techniques to enable and assist the design and evaluation of mm-wave circuits.The standard approach to increase spectral efficiency is to increase the modulation order at the cost of higher transmission power. To improve upon this, a signal structure called spectrally efficient frequency division multiplexing (SEFDM) is utilized. SEFDM adds an additional dimension of continuously tunable spectral efficiency enhancement. Two new variants of SEFDM are implemented and experimentally demonstrated, where both variants are shown to outperform standard signals.A low-cost low-complexity mm-wave transmitter architecture is proposed and experimentally demonstrated. A simple phase retarder predistorter and a frequency multiplier are utilized to successfully generate spectrally efficient mm-wave signals while simultaneously mitigating various issues found in conventional mm-wave systems.A measurement technique to characterize circuits and components under antenna array mutual coupling effects is proposed and demonstrated. With minimal setup requirement, the technique effectively and conveniently maps prescribed transmission scenarios to the measurement environment and offers evaluations of the components in terms of relevant KPIs in addition to conventional metrics.Finally, a technique to estimate transmission and reflection coefficients is proposed and demonstrated. In one variant, the technique enables the coefficients to be estimated using wideband modulated signals, suitable for implementation in measurements performed under real usage scenarios. In another variant, the technique enhances the precision of noisy S-parameter measurements, suitable for characterizations of wideband mm-wave components

Pilot sequence based IQ imbalance estimation and compensation

Abstract. As modern radio access technologies strive to achieve progressively higher data rates and to become increasingly more reliable, minimizing the effects of hardware imperfections becomes a priority. One of those imperfections is in-phase quadrature imbalance (IQI), caused by amplitude and phase response differences between the I and Q branches of the IQ demodulation process. IQI has been shown to deteriorate bit error rates, possibly compromise positioning performance, amongst other effects. Minimizing IQI by tightening hardware manufacturing constraints is not always a commercially viable approach, thus, baseband processing for IQI compensation provides an alternative. The thesis begins by presenting a study in IQI modeling for direct conversion receivers, we then derive a model for general imbalances and show that it reproduces the two most common models in the bibliography. We proceed by exploring some of the existing IQI compensation techniques and discussing their underlying assumptions, advantages, and possible relevant issues. A novel pilot-sequence based approach for tackling IQI estimation and compensation is introduced in this thesis. The idea is to minimize the square Frobenius norm of the error between candidate covariance matrices, which are functions of the candidate IQI parameters, and the sample covariance matrices, obtained from measurements. This new method is first presented in a positioning context with flat fading channels, where IQI compensation is used to improve the positioning estimates mean square error. The technique is then adapted to orthogonal frequency division multiplexing (OFDM) systems,including an version that exploits the 5G New Radio reference signals to estimate the IQI coefficients. We further generalize the new approach to solve joint transmitter and receiver IQI estimation and discuss the implementation details and suggested optimization techniques. The introduced methods are evaluated numerically in their corresponding chapters under a set of different conditions, such as varying signal-to-noise ratio, pilot sequence length, channel model, number of subcarriers, etc. Finally, the proposed compensation approach is compared to other well-established methods by evaluating the bit error rate curves of 5G transmissions. We consistently show that the proposed method is capable of outperforming these other methods if the SNR and pilot sequence length values are sufficiently high. In the positioning simulations, the proposed IQI compensation method was able to improve the root mean squared error (RMSE) of the position estimates by approximately 25 cm. In the OFDM scenario, with high SNR and a long pilot sequence, the new method produced estimates with mean squared error (MSE) about a million times smaller than those from a blind estimator. In bit error rate (BER) simulations, the new method was the only compensation technique capable of producing BER curves similar to the curves without IQI in all of the studied scenarios

Tensor-based signal processing with applications to MIMO-ODFM systems and intelligent reflecting surfaces

Der Einsatz von Tensor-Algebra-Techniken in der Signalverarbeitung hat in den letzten zwei Jahrzehnten zugenommen. Anwendungen wie Bildverarbeitung, biomedizinische Signalverarbeitung, radar, maschinelles Lernen, deep Learning und Kommunikation im Allgemeinen verwenden weitgehend tensorbasierte Verarbeitungstechniken zur Wiederherstellung, Schätzung und Klassifizierung von Signalen. Einer der Hauptgründe für den Einsatz der Tensorsignalverarbeitung ist die Ausnutzung der mehrdimensionalen Struktur von Signalen, wobei die Einzigartigkeitseigenschaften der Tensor-Zerlegung profitieren. Bei der drahtlosen Kommunikation beispielsweise können die Signale mehrere "Dimensionen" haben, wie Raum, Zeit, Frequenz, Polarisation, usw. Diese Arbeit ist in zwei Teile gegliedert. Im ersten Teil betrachten wir die Anwendung von Tensor-basierten Algorithmen für multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) Systeme unter Berücksichtigung von Vorhandensein von Phasenrauschenstörungen. In diesem Teil schlagen wir einen zweistufigen tensorbasierten Empfänger für eine gemeinsame Kanal-, Phasenrausch- und Datenschätzung in MIMO-OFDM-Systemen vor. In der ersten Stufe zeigen wir, dass das empfangene Signal auf den Pilotunterträgern als PARAFAC-Tensor dritter Ordnung modelliert werden kann. Auf der Grundlage dieses Modells werden zwei Algorithmen für die Schätzung der Phasen- und Kanalrauschen in den Pilotton vorgeschlagen. In der zweiten Stufe werden die übertragenen Daten geschätzt. Zu diesem Zweck schlagen wir einen Zero Forcing (ZF)-Empfänger vor, der sich die Tensorstruktur des empfangenen Signals auf den Datenträgern zunutze macht, indem er den vorgeschlagenen selektiven Kronecker-Produkt-Operators (SKP) kapitalisiert. Die Simulationsergebnisse zeigen, dass der vorgeschlagene Empfänger sowohl bei der Symbolfehlerrate als auch beim normalisierten mittleren quadratischen Fehler des geschätzten Kanal- und Phasenrauschmatrizen eine bessere Leistung im Vergleich zum Stand der Technik erzielt. Der zweite Teil dieser Arbeit befasst sich mit der Anwendung der Tensormodellierung zur Reduzierung des Kontrollsignalisierungsoverhead in zukünftigen drahtlosen Systemen, die durch intelligent reconfigurable surfaces (IRSs) unterstützt werden. Zu diesem Zweck schlagen wir eine Annäherung an die nahezu optimalen IRS-Phasenverschiebungen vor, die sonst einen prohibitiv hohen Kommunikationsoverhead auf den BS-IRS-Kontrollverbindungen verursachen würde. Die Hauptidee besteht darin, den optimalen Phasenvektor des IRSs, der Hunderte oder Tausende von Elementen haben kann, durch ein Tensormodell mit niedrigem Rang darzustellen. Dies wird erreicht durch Faktorisierung einer tensorisierten Version des IRS-Phasenverschiebungsvektors, wobei jede Komponente als Kronecker-Produkt einer vordefinierten Anzahl von Faktoren mit kleinerer Größe modelliert wird, die durch Tensor Zerlegungsalgorithmen erhaltet werden können. Wir zeigen, dass die vorgeschlagenen Low-Rank-Modelle die Rückkopplungsanforderungen für die BS-IRS-Kontrollverbindungen drastisch reduzieren. Die Simulationsergebnisse zeigen, dass die vorgeschlagene Methode besonders in Szenarien mit einer starken Sichtverbindung attraktiv sind. In diesem Fall wird fast die gleiche spektrale Effizienz erreicht wie in den Fällen mit nahezu optimalen Phasenverschiebungen, jedoch mit einem drastisch reduzierten Kommunikations-Overhead.The use of tensor algebra techniques in signal processing has been growing over the last two decades. Applications like image processing, biomedical signal processing, radar, machine/deep learning, and communications in general, largely employ tensor-based techniques for recovery, estimating, and classifying signals. One of the main reasons for using tensor signal processing is the exploitation of the multidimensional structure of signals, while benefiting from the uniqueness properties of tensor decomposition. For example, in wireless communications, the signals can have several “dimensions", e.g., space, time, frequency, polarization, beamspace, etc. This thesis is divided into two parts, first, in the application of a tensor-based algorithm in multiple-input multiple-output (MIMO)-orthogonal frequency division multiplexing (OFDM) systems with the presence of phase-noise impairments. In this first part, we propose a two-stage tensor-based receiver for a joint channel, phase-noise, and data estimation in MIMO-OFDM systems. In the first stage, we show that the received signal at the pilot subcarriers can be modeled as a third-order PARAFAC tensor. Based on this model, we propose two algorithms for channel and phase-noise estimation at the pilot subcarriers. The second stage consists of data estimation, for which we propose a ZF receiver that capitalizes on the tensor structure of the received signal at the data subcarriers using the proposed SKP operator. Numerical simulations show that the proposed receivers achieves an improved performance compared to the state-of-art receivers in terms of symbol error rate (SER) and normalized mean square error (NMSE) of the estimated channel and phase-noise matrices. The second part of this thesis focuses on the application of tensor modeling to reduce the control signaling overhead in future wireless systems aided by intelligent reconfigurable surfaces (IRS). To this end, we propose a low-rank approximation of the near-optimal IRS phase-shifts, which would incur prohibitively high communication overhead on the BS-IRS controller links. The key idea is to represent the potentially large IRS phase-shift vector using a low-rank tensor model. This is achieved by factorizing a tensorized version of the IRS phase-shift vector, where each component is modeled as the Kronecker product of a predefined number of factors of smaller sizes, which can be obtained via tensor decomposition algorithms. We show that the proposed low-rank models drastically reduce the required feedback requirements associated with the BS-IRS control links. Simulation results indicate that the proposed method is especially attractive in scenarios with a strong line of sight component, in which case nearly the same spectral efficiency is reached as in the cases with near-optimal phase-shifts, but with a drastically reduced communication overhead

MIMO-UFMC Transceiver Schemes for Millimeter Wave Wireless Communications

The UFMC modulation is among the most considered solutions for the realization of beyond-OFDM air interfaces for future wireless networks. This paper focuses on the design and analysis of an UFMC transceiver equipped with multiple antennas and operating at millimeter wave carrier frequencies. The paper provides the full mathematical model of a MIMO-UFMC transceiver, taking into account the presence of hybrid analog/digital beamformers at both ends of the communication links. Then, several detection structures are proposed, both for the case of single-packet isolated transmission, and for the case of multiple-packet continuous transmission. In the latter situation, the paper also considers the case in which no guard time among adjacent packets is inserted, trading off an increased level of interference with higher values of spectral efficiency. At the analysis stage, the several considered detection structures and transmission schemes are compared in terms of bit-error-rate, root-mean-square-error, and system throughput. The numerical results show that the proposed transceiver algorithms are effective and that the linear MMSE data detector is capable of well managing the increased interference brought by the removal of guard times among consecutive packets, thus yielding throughput gains of about 10 - 13 $\%$. The effect of phase noise at the receiver is also numerically assessed, and it is shown that the recursive implementation of the linear MMSE exhibits some degree of robustness against this disturbance

A two phase framework for visible light-based positioning in an indoor environment: performance, latency, and illumination

Recently with the advancement of solid state lighting and the application thereof to Visible Light Communications (VLC), the concept of Visible Light Positioning (VLP) has been targeted as a very attractive indoor positioning system (IPS) due to its ubiquity, directionality, spatial reuse, and relatively high modulation bandwidth. IPSs, in general, have 4 major components (1) a modulation, (2) a multiple access scheme, (3) a channel measurement, and (4) a positioning algorithm. A number of VLP approaches have been proposed in the literature and primarily focus on a fixed combination of these elements and moreover evaluate the quality of the contribution often by accuracy or precision alone. In this dissertation, we provide a novel two-phase indoor positioning algorithmic framework that is able to increase robustness when subject to insufficient anchor luminaries and also incorporate any combination of the four major IPS components. The first phase provides robust and timely albeit less accurate positioning proximity estimates without requiring more than a single luminary anchor using time division access to On Off Keying (OOK) modulated signals while the second phase provides a more accurate, conventional, positioning estimate approach using a novel geometric constrained triangulation algorithm based on angle of arrival (AoA) measurements. However, this approach is still an application of a specific combination of IPS components. To achieve a broader impact, the framework is employed on a collection of IPS component combinations ranging from (1) pulsed modulations to multicarrier modulations, (2) time, frequency, and code division multiple access, (3) received signal strength (RSS), time of flight (ToF), and AoA, as well as (4) trilateration and triangulation positioning algorithms. Results illustrate full room positioning coverage ranging with median accuracies ranging from 3.09 cm to 12.07 cm at 50% duty cycle illumination levels. The framework further allows for duty cycle variation to include dimming modulations and results range from 3.62 cm to 13.15 cm at 20% duty cycle while 2.06 cm to 8.44 cm at a 78% duty cycle. Testbed results reinforce this frameworks applicability. Lastly, a novel latency constrained optimization algorithm can be overlaid on the two phase framework to decide when to simply use the coarse estimate or when to expend more computational resources on a potentially more accurate fine estimate. The creation of the two phase framework enables robust, illumination, latency sensitive positioning with the ability to be applied within a vast array of system deployment constraints