A computer simulation of the turbocharged turbo compounded diesel engine system: A description of the thermodynamic and heat transfer models

A computer simulation of the turbocharged turbocompounded direct-injection diesel engine system was developed in order to study the performance characteristics of the total system as major design parameters and materials are varied. Quasi-steady flow models of the compressor, turbines, manifolds, intercooler, and ducting are coupled with a multicylinder reciprocator diesel model, where each cylinder undergoes the same thermodynamic cycle. The master cylinder model describes the reciprocator intake, compression, combustion and exhaust processes in sufficient detail to define the mass and energy transfers in each subsystem of the total engine system. Appropriate thermal loading models relate the heat flow through critical system components to material properties and design details. From this information, the simulation predicts the performance gains, and assesses the system design trade-offs which would result from the introduction of selected heat transfer reduction materials in key system components, over a range of operating conditions

Computer simulation of the heavy-duty turbo-compounded diesel cycle for studies of engine efficiency and performance

Reductions in heat loss at appropriate points in the diesel engine which result in substantially increased exhaust enthalpy were shown. The concepts for this increased enthalpy are the turbocharged, turbocompounded diesel engine cycle. A computer simulation of the heavy duty turbocharged turbo-compounded diesel engine system was undertaken. This allows the definition of the tradeoffs which are associated with the introduction of ceramic materials in various parts of the total engine system, and the study of system optimization. The basic assumptions and the mathematical relationships used in the simulation of the model engine are described

A two-dimensional numerical study of the flow inside the combustion chambers of a motored rotary engine

A numerical study was performed to investigate the unsteady, multidimensional flow inside the combustion chambers of an idealized, two-dimensional, rotary engine under motored conditions. The numerical study was based on the time-dependent, two-dimensional, density-weighted, ensemble-averaged conservation equations of mass, species, momentum, and total energy valid for two-component ideal gas mixtures. The ensemble-averaged conservation equations were closed by a K-epsilon model of turbulence. This K-epsilon model of turbulence was modified to account for some of the effects of compressibility, streamline curvature, low-Reynolds number, and preferential stress dissipation. Numerical solutions to the conservation equations were obtained by the highly efficient implicit-factored method of Beam and Warming. The grid system needed to obtain solutions were generated by an algebraic grid generation technique based on transfinite interpolation. Results of the numerical study are presented in graphical form illustrating the flow patterns during intake, compression, gaseous fuel injection, expansion, and exhaust

Catalog of selected heavy duty transport energy management models

A catalog of energy management models for heavy duty transport systems powered by diesel engines is presented. The catalog results from a literature survey, supplemented by telephone interviews and mailed questionnaires to discover the major computer models currently used in the transportation industry in the following categories: heavy duty transport systems, which consist of highway (vehicle simulation), marine (ship simulation), rail (locomotive simulation), and pipeline (pumping station simulation); and heavy duty diesel engines, which involve models that match the intake/exhaust system to the engine, fuel efficiency, emissions, combustion chamber shape, fuel injection system, heat transfer, intake/exhaust system, operating performance, and waste heat utilization devices, i.e., turbocharger, bottoming cycle

Entropy generation and jet engine optimization

In 2009, it was shown that, with an original approach to hydrodynamic cavitation, a phenomenological model was realized in order to compute some of the physical parameters needed for the design of the most common technological applications (turbo-machinery, etc.) with an economical saving in planning because this analysis could allow engineers to reduce the experimental tests and the consequent costs in the design process. Here the same approach has been used to obtain range of some physical quantity for jet engine optimization

Ignition by air injection (CIBAI) for controlled auto-ignition in a CFR engine

Compression ignition by air injection (CIBAI) has been successfully achieved in a modified single cylinder, four-stroke, spark ignition cooperative fuel research (CFR) engine. The CIBAI cycle was invented by Professor John Loth and Professor Gary Morris, US patent No\u27s: 6,994,057 Feb. 7, 2006 and 6,899,061 May 31, 2005. This new revolutionary combustion concept has the potential to become an alternative to traditional (SI) spark ignited and compression ignited (CI) diesel engines.;The objective of this dissertation was to demonstrate experimentally the viability of achieving ignition by air injection (CIBAI) for controlled auto-ignition in a CFR engine. This experimental work involved the development of an air injection model, and the design, assembly, and testing of a highly specialized air injection and timing equipment. These experiments were designed to substitute CIBAI ignition for one cycle in a spark ignition engine. The CIBAI engine cycle analysis is included, followed by an analytical model of the air injection process. A controller for the air injection and timing system had been designed, built and tested under different operating conditions until a satisfactory experimental procedure was developed for testing using the CIBAI concept. Based on the measured pressure-time history a numerical modeling code was developed to analyze power and combustion parameters (indicated net work, indicated mean effective pressure (IMEP), net heat release, net heat release rate, mass fraction burned (MFB), temperature history, combustion duration, and ignition delay). Finally, a parametric study was conducted to determine the effect of compression ratio, intake temperature, air-fuel ratio, air preheated charging pressure, and air-injection timing on CIBAI combustion.;Experimental and numerical model results indicated that ignition is readily achieved by air injection (CIBAI) in a CFR engine using the proper air injection system and proper air injection timing strategy

Analysis of rotary engine combustion processes based on unsteady, three-dimensional computations

A new computer code was developed for predicting the turbulent, and chemically reacting flows with sprays occurring inside of a stratified charge rotary engine. The solution procedure is based on an Eulerian Lagrangian approach where the unsteady, 3-D Navier-Stokes equations for a perfect gas mixture with variable properties are solved in generalized, Eulerian coordinates on a moving grid by making use of an implicit finite volume, Steger-Warming flux vector splitting scheme, and the liquid phase equations are solved in Lagrangian coordinates. Both the details of the numerical algorithm and the finite difference predictions of the combustor flow field during the opening of exhaust and/or intake, and also during fuel vaporization and combustion, are presented

Transient performance simulation of gas turbine engine integrated with fuel and control systems

Two new methods for the simulation of gas turbine fuel systems, one based on an inter-component volume (ICV) method, and the other based on the iterative Newton Raphson (NR) method, have been developed in this study. They are able to simulate the performance behaviour of each of the hydraulic components such as pumps, valves, metering unit of a fuel system, using physics-based models, which potentially offer more accurate results compared with those using transfer functions. A transient performance simulation system has been set up for gas turbine engines based on an inter-component volume (ICV). A proportional- integral (PI) control strategy is used for the simulation of engine control systems. An integrated engine and its control and hydraulic fuel systems has been set up to investigate their coupling effect during engine transient processes. The developed simulation methods and the systems have been applied to a model turbojet and a model turboshaft gas turbine engine to demonstrate the effectiveness of both two methods. The comparison between the results of engines with and without the ICV method simulated fuel system models shows that the delay of the engine transient response due to the inclusion of the fuel system components and introduced inter-component volumes is noticeable, although relatively small. The comparison of two developed methods applied to engine fuel system simulation demonstrate that both methods introduce delay effect to the engine transient response but the NR method is ahead than the ICV method due to the omission of inter-component volumes on engine fuel system simulation. The developed simulation methods are generic and can be applied to the performance simulation of any other gas turbines and their control and fuel systems. A sensitivity analysis of fuel system key parameters that may affect the engine transient behaviours has also been achieved and represented in this thesis. Three sets of fuel system key parameters have been introduced to investigate their sensitivities, which are, the volumes introduced for ICV method applied to fuel system simulation; the time constants introduced into those first order lags tosimulate the valve movements delay and fuel spray delay effect; and the fuel system key performance and structural parameters

Numerical Model of a Variable-Combined-Cycle Engine for Dual Subsonic and Supersonic Cruise

Efficient high speed propulsion requires exploiting the cooling capability of the cryogenic fuel in the propulsion cycle. This paper presents the numerical model of a combined cycle engine while in air turbo-rocket configuration. Specific models of the various heat exchanger modules and the turbomachinery elements were developed to represent the physical behavior at off-design operation. The dynamic nature of the model allows the introduction of the engine control logic that limits the operation of certain subcomponents and extends the overall engine operational envelope. The specific impulse and uninstalled thrust are detailed while flying a determined trajectory between Mach 2.5 and 5 for varying throttling levels throughout the operational envelope