An integrated placement and routing approach

As the feature size continues scaling down, interconnects become the major contributor of signal delay. Since interconnects are mainly determined by placement and routing, these two stages play key roles to achieve high performance. Historically, they are divided into two separate stages to make the problem tractable. Therefore, the routing information is not available during the placement process. Net models such as HPWL, are employed to approximate the routing to simplify the placement problem. However, the good placement in terms of these objectives may not be routable at all in the routing stage because different objectives are optimized in placement and routing stages. This inconsistancy makes the results obtained by the two-step optimization method far from optimal;In order to achieve high-quality placement solution and ensure the following routing, we propose an integrated placement and routing approach. In this approach, we integrate placement and routing into the same framework so that the objective optimized in placement is the same as that in routing. Since both placement and routing are very hard problems (NP-hard), we need to have very efficient algorithms so that integrating them together will not lead to intractable complexity;In this dissertation, we first develop a highly efficient placer - FastPlace 3.0 for large-scale mixed-size placement problem. Then, an efficient and effective detailed placer - FastDP is proposed to improve global placement by moving standard cells in designs. For high-degree nets in designs, we propose a novel performance-driven topology design algorithm to generate good topologies to achieve very strict timing requirement. In the routing phase, we develop two global routers, FastRoute and FastRoute 2.0. Compared to traditional global routers, they can generate better solutions and are two orders of magnitude faster. Finally, based on these efficient and high-quality placement and routing algorithms, we propose a new flow which integrates placement and routing together closely. In this flow, global routing is extensively applied to obtain the interconnect information and direct the placement process. In this way, we can get very good placement solutions with guaranteed routability

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi

Handling the complexity of routing problem in modern VLSI design

In VLSI physical design, the routing task consists of using over-the-cell metal wires to connect pins and ports of circuit gates and blocks. Traditionally, VLSI routing is an important design step in the sense that the quality of routing solution has great impact on various design metrics such as circuit timing, power consumption, chip reliability and manufacturability etc. As the advancing VLSI design enters the nanometer era, the routing success (routability issue) has been arising as one of the most critical problems in back-end design. In one aspect, the degree of design complexity is increasing dramatically as more and more modules are integrated into the chip. Much higher chip density leads to higher routing demands and potentially more risks in routing failure. In another aspect, with decreasing design feature size, there are more complex design rules imposed to ensure manufacturability. These design rules are hard to satisfy and they usually create more barriers for achieving routing closure (i.e., generate DRC free routing solution) and thus affect chip time to market (TTM) plan. In general, the behavior and performance of routing are affected by three consecutive phases: placement phase, global routing phase and detailed routing phase in a typical VLSI physical design flow. Traditional CAD tools handle each of the three phases independently and the global picture of the routability issue is neglected. Different from conventional approaches which propose tools and algorithms for one particular design phase, this thesis investigates the routability issue from all three phases and proposes a series of systematic solutions to build a more generic flow and improve quality of results (QoR). For the placement phase, we will introduce a mixed-sized placement refinement tool for alleviating congestion after placement. The tool shifts and relocates modules based on a global routing estimation. For the global routing phase, a very fast and effective global router is developed. Its performance surpasses many peer works as verified by ISPD 2008 global routing contest results. In the detailed routing phase, a tool is proposed to perform detailed routing using regular routing patterns based on a correct-by-construction methodology to improve routability as well as satisfy most design rules. Finally, the tool which integrates global routing and detailed routing is developed to remedy the inconsistency between global routing and detailed routing. To verify the algorithms we proposed, three sets of testcases derived from ISPD98 and ISPD05/06 placement benchmark suites are proposed. The results indicate that our proposed methods construct an integrated and systematic flow for routability improvement which is better than conventional methods

A Multiple-objective ILP based Global Routing Approach for VLSI ASIC Design

A VLSI chip can today contain hundreds of millions transistors and is expected to contain more than 1 billion transistors in the next decade. In order to handle this rapid growth in integration technology, the design procedure is therefore divided into a sequence of design steps. Circuit layout is the design step in which a physical realization of a circuit is obtained from its functional description. Global routing is one of the key subproblems of the circuit layout which involves finding an approximate path for the wires connecting the elements of the circuit without violating resource constraints. The global routing problem is NP-hard, therefore, heuristics capable of producing high quality routes with little computational effort are required as we move into the Deep Sub-Micron (DSM) regime. In this thesis, different approaches for global routing problem are first reviewed. The advantages and disadvantages of these approaches are also summarized. According to this literature review, several mathematical programming based global routing models are fully investigated. Quality of solution obtained by these models are then compared with traditional Maze routing technique. The experimental results show that the proposed model can optimize several global routing objectives simultaneously and effectively. Also, it is easy to incorporate new objectives into the proposed global routing model. To speedup the computation time of the proposed ILP based global router, several hierarchical methods are combined with the flat ILP based global routing approach. The experimental results indicate that the bottom-up global routing method can reduce the computation time effectively with a slight increase of maximum routing density. In addition to wire area, routability, and vias, performance and low power are also important goals in global routing, especially in deep submicron designs. Previous efforts that focused on power optimization for global routing are hindered by excessively long run times or the routing of a subset of the nets. Accordingly, a power efficient multi-pin global routing technique (PIRT) is proposed in this thesis. This integer linear programming based techniques strives to find a power efficient global routing solution. The results indicate that an average power savings as high as 32\% for the 130-nm technology can be achieved with no impact on the maximum chip frequency

FieldPlacer - A flexible, fast and unconstrained force-directed placement method for heterogeneous reconfigurable logic architectures

The field of placement methods for components of integrated circuits, especially in the domain of reconfigurable chip architectures, is mainly dominated by a handful of concepts. While some of these are easy to apply but difficult to adapt to new situations, others are more flexible but rather complex to realize. This work presents the FieldPlacer framework, a flexible, fast and unconstrained force-directed placement method for heterogeneous reconfigurable logic architectures, in particular for the ever important heterogeneous FPGAs. In contrast to many other force-directed placers, this approach is called ‘unconstrained’ as it does not require a priori fixed logic elements in order to calculate a force equilibrium as the solution to a system of equations. Instead, it is based on a free spring embedder simulation of a graph representation which includes all logic block types of a design simultaneously. The FieldPlacer framework offers a huge amount of flexibility in applying different distance norms (e. g., the Manhattan distance) for the force-directed layout and aims at creating adapted layouts for various objective functions, e. g., highest performance or improved routability. Depending on the individual situation, a runtime-quality trade-off can be considered to either produce a decent placement in a very short time or to generate an exceptionally good placement, which takes longer. An extensive comparison with the latest simulated annealing placement method from the well-known Versatile Place and Route (VPR) framework shows that the FieldPlacer approach can create placements of comparable quality much faster than VPR or, alternatively, generate better placements in the same time. The flexibility in defining arbitrary objective functions and the intuitive adaptability of the method, which, among others, includes different concepts from the field of graph drawing, should facilitate further developments with this framework, e. g., for new upcoming optimization targets like the energy consumption of an implemented design

Shortest Paths and Steiner Trees in VLSI Routing

Routing is one of the major steps in very-large-scale integration (VLSI) design. Its task is to find disjoint wire connections between sets of points on a chip, subject to numerous constraints. This problem is solved in a two-stage approach, which consists of so-called global and detailed routing steps. For each set of metal components to be connected, global routing reduces the search space by computing corridors in which detailed routing sequentially determines the desired connections as shortest paths. In this thesis, we present new theoretical results on Steiner trees and shortest paths, the two main mathematical concepts in routing. In the practical part, we give computational results of BonnRoute, a VLSI routing tool developed at the Research Institute for Discrete Mathematics at the University of Bonn. Interconnect signal delays are becoming increasingly important in modern chip designs. Therefore, the length of paths or direct delay measures should be taken into account when constructing rectilinear Steiner trees. We consider the problem of finding a rectilinear Steiner minimum tree (RSMT) that --- as a secondary objective --- minimizes a signal delay related objective. Given a source we derive some structural properties of RSMTs for which the weighted sum of path lengths from the source to the other terminals is minimized. Also, we present an exact algorithm for constructing RSMTs with weighted sum of path lengths as secondary objective, and a heuristic for various secondary objectives. Computational results for industrial designs are presented. We further consider the problem of finding a shortest rectilinear Steiner tree in the plane in the presence of rectilinear obstacles. The Steiner tree is allowed to run over obstacles; however, if it intersects an obstacle, then no connected component of the induced subtree must be longer than a given fixed length. This kind of length restriction is motivated by its application in VLSI routing where a large Steiner tree requires the insertion of repeaters which must not be placed on top of obstacles. We show that there are optimal length-restricted Steiner trees with a special structure. In particular, we prove that a certain graph (called augmented Hanan grid) always contains an optimal solution. Based on this structural result, we give an approximation scheme for the special case that all obstacles are of rectangular shape or are represented by at most a constant number of edges. Turning to the shortest paths problem, we present a new generic framework for Dijkstra's algorithm for finding shortest paths in digraphs with non-negative integral edge lengths. Instead of labeling individual vertices, we label subgraphs which partition the given graph. Much better running times can be achieved if the number of involved subgraphs is small compared to the order of the original graph and the shortest path problems restricted to these subgraphs is computationally easy. As an application we consider the VLSI routing problem, where we need to find millions of shortest paths in partial grid graphs with billions of vertices. Here, the algorithm can be applied twice, once in a coarse abstraction (where the labeled subgraphs are rectangles), and once in a detailed model (where the labeled subgraphs are intervals). Using the result of the first algorithm to speed up the second one via goal-oriented techniques leads to considerably reduced running time. We illustrate this with the routing program BonnRoute on leading-edge industrial chips. Finally, we present computational results of BonnRoute obtained on real-world VLSI chips. BonnRoute fulfills all requirements of modern VLSI routing and has been used by IBM and its customers over many years to produce more than one thousand different chips. To demonstrate the strength of BonnRoute as a state-of-the-art industrial routing tool, we show that it performs excellently on all traditional quality measures such as wire length and number of vias, but also on further criteria of equal importance in the every-day work of the designer

Timing-Driven Macro Placement

Placement is an important step in the process of finding physical layouts for electronic computer chips. The basic task during placement is to arrange the building blocks of the chip, the circuits, disjointly within a given chip area. Furthermore, such positions should result in short circuit interconnections which can be routed easily and which ensure all signals arrive in time. This dissertation mostly focuses on macros, the largest circuits on a chip. In order to optimize timing characteristics during macro placement, we propose a new optimistic timing model based on geometric distance constraints. This model can be computed and evaluated efficiently in order to predict timing traits accurately in practice. Packing rectangles disjointly remains strongly NP-hard under slack maximization in our timing model. Despite of this we develop an exact, linear time algorithm for special cases. The proposed timing model is incorporated into BonnMacro, the macro placement component of the BonnTools physical design optimization suite developed at the Research Institute for Discrete Mathematics. Using efficient formulations as mixed-integer programs we can legalize macros locally while optimizing timing. This results in the first timing-aware macro placement tool. In addition, we provide multiple enhancements for the partitioning-based standard circuit placement algorithm BonnPlace. We find a model of partitioning as minimum-cost flow problem that is provably as small as possible using which we can avoid running time intensive instances. Moreover we propose the new global placement flow Self-Stabilizing BonnPlace. This approach combines BonnPlace with a force-directed placement framework. It provides the flexibility to optimize the two involved objectives, routability and timing, directly during placement. The performance of our placement tools is confirmed on a large variety of academic benchmarks as well as real-world designs provided by our industrial partner IBM. We reduce running time of partitioning significantly and demonstrate that Self-Stabilizing BonnPlace finds easily routable placements for challenging designs – even when simultaneously optimizing timing objectives. BonnMacro and Self-Stabilizing BonnPlace can be combined to the first timing-driven mixed-size placement flow. This combination often finds placements with competitive timing traits and even outperforms solutions that have been determined manually by experienced designers