MODELING, DESIGN, AND IMPLEMENTATION OF HIGH GAIN POWER ELECTRONIC DC-DC CONVERTERS FOR NANOGRID APPLICATIONS

Nanogrids are nothing but power distribution systems that are based on renewable energy sources and are apt for low-power home applications. Nanogrids are considered to be the building cells of a Microgrid. Nanogrid is intended for feeding domestic loads (of the order of 100 W to 5 kW) from renewable energy sources such as wind farms, roof-top solar photovoltaic, biomass, and fuel cell, etc. Nonetheless, the voltages produced by these renewable energy sources are small and not sufficient enough to be utilized in all the applications. Hence, it is necessary to include high gain and high-efficiency DC-DC converters in the system. To interface the generators and the loads, power electronic converters are employed within a Nanogrid. The power system grid is also linked to the Nanogrid using these converters. The most fundamental characteristics of the high-gain DC-DC converters are high efficiency, high-voltage gain, and low voltage/current stress on switching components. A comprehensive literature review of various boosting methods is disseminated in this research work. After a detailed investigation, five new DC-DC power converter topologies have been designed and developed to achieve high gain factors with reduced switch ratings and low cost for use in Nanogrids. The proposed converters cannot only reduce voltage/current stresses across the switching components significantly but also achieve a higher voltage gain at moderate duty cycles with a lesser number of components. Moreover, the proposed converters are designed in such a way that they can maintain a continuous input current, and hence making them useful for power conversion in the battery, fuel cell, and solar PV applications. By using boosting technique five novel high voltage gain DC-DC converters are developed and presented in the dissertation, namely: 1. modified Switched Inductor Boost Converter (mSIBC) with reduced switch voltage stress, 2. Transformer-less Boost Converter (TBC) with reduced voltage stress, 3. Switched-Inductor based DC-DC Converter with reduced switch current stress, 4. Novel High Gain Active Switched Network-Based Converter, and 5. Double Stage Converter with low current stress for Nanogrid The detailed theoretical analysis of the voltage conversion ratio, parameter design, continuous and discontinuous conduction mode, and advantages are presented. In addition, a detailed comparative study of each converter topology is also given. The functionality of the proposed power converters is tested in real-time by developing Laboratory prototypes of the proposed converters and the theoretical analysis is validated by obtaining the experimental results. The proposed converter configurations are simulated in MATLAB as well, to verify the theoretical analysis. Simulation results of all the proposed converters are presented indicating clear evidence of the expected predictions in close proximity with experimental results

Cakar ayam shaping machine

Cakar ayam (Figure 7.1) is one of the Malay traditional cookies that are made from sliced sweet potatoes deep-fried in the coconut candy. In current practice of moulding the cookies, the fried sweet potatoes are molded using traditional manual tools, which are inefficient and less productive for the mass production purposes. “Kuih cakar ayam” associated with the meaning of the idiom means less messy handwriting has a somewhat negative connotation .This cookies may just seem less attractive in shape but still likeable . In fact, this cookie is considered a popular snack even outside the holiday season. The choice of the name of this cookie is more to shape actually resembles former chicken scratches made by the paw the ground while foraging. The value of wisdom, beauty and creativity of the Malays is clearly evident through the Malay cookie. Although it is attacked by the invention of modern cakes that look far more interesting, these cakes will be able to survive a long time until now

Power Quality Improvement and Low Voltage Ride through Capability in Hybrid Wind-PV Farms Grid-Connected Using Dynamic Voltage Restorer

© 2018 IEEE. Translations and content mining are permitted for academic research only. Personal use is also permitted, but republication/redistribution requires IEEE permission.This paper proposes the application of a dynamic voltage restorer (DVR) to enhance the power quality and improve the low voltage ride through (LVRT) capability of a three-phase medium-voltage network connected to a hybrid distribution generation system. In this system, the photovoltaic (PV) plant and the wind turbine generator (WTG) are connected to the same point of common coupling (PCC) with a sensitive load. The WTG consists of a DFIG generator connected to the network via a step-up transformer. The PV system is connected to the PCC via a two-stage energy conversion (dc-dc converter and dc-ac inverter). This topology allows, first, the extraction of maximum power based on the incremental inductance technique. Second, it allows the connection of the PV system to the public grid through a step-up transformer. In addition, the DVR based on fuzzy logic controller is connected to the same PCC. Different fault condition scenarios are tested for improving the efficiency and the quality of the power supply and compliance with the requirements of the LVRT grid code. The results of the LVRT capability, voltage stability, active power, reactive power, injected current, and dc link voltage, speed of turbine, and power factor at the PCC are presented with and without the contribution of the DVR system.Peer reviewe

The road to fully integrated DC-DC conversion via the switched-capacitor approach

This paper provides a perspective on progress toward realization of efficient, fully integrated dc-dc conversion and regulation functionality in CMOS platforms. In providing a comparative assessment between the inductor-based and switched-capacitor approaches, the presentation reviews the salient features in effectiveness in utilization of switch technology and in use and implementation of passives. The analytical conclusions point toward the strong advantages of the switched-capacitor (SC) approach with respect to both switch utilization and much higher energy densities of capacitors versus inductors. The analysis is substantiated with a review of recently developed and published integrated dc-dc converters of both the inductor-based and SC types. © 2012 IEEE

Power Quality Enhancement in Electricity Grids with Wind Energy Using Multicell Converters and Energy Storage

In recent years, the wind power industry is experiencing a rapid growth and more wind farms with larger size wind turbines are being connected to the power system. While this contributes to the overall security of electricity supply, large-scale deployment of wind energy into the grid also presents many technical challenges. Most of these challenges are one way or another, related to the variability and intermittent nature of wind and affect the power quality of the distribution grid. Power quality relates to factors that cause variations in the voltage level and frequency as well as distortion in the voltage and current waveforms due to wind variability which produces both harmonics and inter-harmonics. The main motivation behind work is to propose a new topology of the static AC/DC/AC multicell converter to improve the power quality in grid-connected wind energy conversion systems. Serial switching cells have the ability to achieve a high power with lower-size components and improve the voltage waveforms at the input and output of the converter by increasing the number of cells. Furthermore, a battery energy storage system is included and a power management strategy is designed to ensure the continuity of power supply and consequently the autonomy of the proposed system. The simulation results are presented for a 149.2 kW wind turbine induction generator system and the results obtained demonstrate the reduced harmonics, improved transient response, and reference tracking of the voltage output of the wind energy conversion system.Peer reviewedFinal Accepted Versio

AC vs. DC Boost Converters: A Detailed Conduction Loss Comparison

Studies have shown the efficiency benefits of DC dis- tribution systems are largely due to the superior performance of DC/DC converters. Nonetheless, these studies are often based on product data that differs widely in manufacturer and operating voltage. This work develops a rigorous loss model to theoretically compare the efficiency of a DC/DC and an AC/DC PFC boost converter. It ensures each converter has the same components and equivalent operating voltages. The results show AC boost converters below 500 W to have 2.9 to 4.2 times the loss of DC

Modular converter system for low-cost off-grid energy storage using second life Li-ion batteries

Lithium ion batteries are promising for small off- grid energy storage applications in developing countries because of their high energy density and long life. However, costs are prohibitive. Instead, we consider 'used' Li-ion batteries for this application, finding experimentally that many discarded laptop cells, for example, still have good capacity and cycle life. In order to make safe and optimal use of such cells, we present a modular power management system using a separate power converter for every cell. This novel approach allows individual batteries to be used to their full capacity. The power converters operate in voltage droop control mode to provide easy charge balancing and implement a battery management system to estimate the capacity of each cell, as we demonstrate experimentally.Comment: Presented at IEEE GHTC Oct 10-14, 2014, Silicon Valle

Hydrogen vs. Battery in the long-term operation. A comparative between energy management strategies for hybrid renewable microgrids

The growth of the world’s energy demand over recent decades in relation to energy intensity and demography is clear. At the same time, the use of renewable energy sources is pursued to address decarbonization targets, but the stochasticity of renewable energy systems produces an increasing need for management systems to supply such energy volume while guaranteeing, at the same time, the security and reliability of the microgrids. Locally distributed energy storage systems (ESS) may provide the capacity to temporarily decouple production and demand. In this sense, the most implemented ESS in local energy districts are small–medium-scale electrochemical batteries. However, hydrogen systems are viable for storing larger energy quantities thanks to its intrinsic high mass-energy density. To match generation, demand and storage, energy management systems (EMSs) become crucial. This paper compares two strategies for an energy management system based on hydrogen-priority vs. battery-priority for the operation of a hybrid renewable microgrid. The overall performance of the two mentioned strategies is compared in the long-term operation via a set of evaluation parameters defined by the unmet load, storage efficiency, operating hours and cumulative energy. The results show that the hydrogen-priority strategy allows the microgrid to be led towards island operation because it saves a higher amount of energy, while the battery-priority strategy reduces the energy efficiency in the storage round trip. The main contribution of this work lies in the demonstration that conventional EMS for microgrids’ operation based on battery-priority strategy should turn into hydrogen-priority to keep the reliability and independence of the microgrid in the long-term operation

Hybrid photovoltaic-thermoelectric generator powered synchronous reluctance motor for pumping applications

The interest in photovoltaic (PV) pumping systems has increased, particularly in rural areas where there is no grid supply available. However, both the performance and the cost of the whole system are still an obstacle for a wide spread of this technology. In this article, a hybrid photovoltaic (PV)-thermoelectric generator (TEG) is investigated for pumping applications. The electric drivetrain comprises a synchronous reluctance motor and an inverter. A control strategy for the drivetrain is employed to execute two main tasks: 1) driving the motor properly to achieve a maximum torque per Ampere condition and 2) maximizing the output power of the PV system at different weather conditions. This means that the conventional DC-DC converter is not used in the proposed system. Moreover, batteries, which are characterized by short life expectancy and high replacement cost, are also not used. It is found that the motor output power and the pump flow rate are increased by about 9.5% and 12% respectively when the hybrid PV-TEG array is used compared to only using PV array. Accordingly, the performance, cost and complexity of the system are improved. Measurements on an experimental laboratory setup are constructed to validate the theoretical results of this work

Direct usage of photovoltaic solar panels to supply a freezer motor with variable DC input voltage

In this paper, a single-phase photovoltaic (PV) inverter fed by a boost converter to supply a freezer motor with variable DC input is investigated. The proposed circuit has two stages. Firstly, the DC output of the PV panel that varies between 150 and 300 V will be applied to the boost converter. The boost converter will boost the input voltage to a fixed 300 V DC. Next, this voltage is supplied to the single-phase full-bridge inverter to obtain 230 V AC. In the end, The output of the inverter will feed a freezer motor. The PV panels can be stand-alone or grid-connected. The grid-connected PV is divided into two categories, such as with a transformer and without a transformer, a transformer type has galvanic isolation resulting in increasing the security and also provides no further DC current toward the grid, but it is expensive, heavy and bulky. The transformerless type holds high efficiency and it is cheaper, but it suffers from leakage current between PV and the grid. This paper proposes a stand-alone direct use of PV to supply a freezer; therefore, no grid connection will result in no leakage current between the PV and Grid. The proposed circuit has some features such as no filtering circuit at the output of the inverter, no battery in the system, DC-link instead of AC link that reduces no-loads, having a higher efficiency, and holding enough energy in the DC-link capacitor to get the motor started. The circuit uses no transformers, thus, it is cheaper and has a smaller size. In addition, the system does not require a complex pulse width modulation (PWM) technique, because the motor can operate with a pulsed waveform. The control strategy uses the PWM signal with the desired timing. With this type of square wave, the harmonics (5th and 7th) of the voltage are reduced. The experimental and simulation results are presented to verify the feasibility of the proposed strategy