Design and Implementation of Novel High Performance Domino Logic

This dissertation presents design and implementation of novel high performance domino logic techniques with increased noise robustness and reduced leakages. The speed and overhead area became the primary parameters of choice for fabrication industry that led to invention of clocked logic styles named as Dynamic logic and Domino logic families. Most importantly, power consumption, noise immunity, speed of operation, area and cost are the predominant parameters for designing any kind of digital logic circuit technique with effective trade-off amongst these parameters depending on the situation and application of design. Because of its high speed and low overhead area domino logic became process of choice for designing of high speed application circuits. The concerning issues are large power consumption and high sensitivity towards noise. Hence, there is a need for designing new domino methodology to meet the requirements by overcoming above mentioned drawbacks which led to ample opportunities for diversified research in this field. Therefore, the outcome of research must be able to handle the primary design parameters efficiently. Besides this, the designed circuit must exhibit high degree of robustness towards noise.In this thesis, few domino logic circuit techniques are proposed to deal with noise and sub-threshold leakages. Effect of signal integrity issues on domino logic techniques is studied. Furthermore, having been subjected to process corner analysis and noise analysis, the overall performance of proposed domino techniques is found to be enhanced despite a few limitations that are mentioned in this work. Besides this, lector based domino and dynamic node stabilized techniques are also proposed and are investigated thoroughly. Simulations show that proposed circuits are showing superior performance. In addition to this, domino based Schmitt triggers with various hysteresis phenomena are designed and simulated. Pre-layout and post-layout simulation results are compared for proposed Schmitt trigger. Simulations reveal that proposed Schmitt trigger techniques are more noise tolerant than CMOS counterparts. Moreover, a test chip for domino based Schmitt trigger is done in UMC 180 nm technology for fabrication

Improved Techniques for High Performance Noise-Tolerant Domino CMOS Logic Circuits

Domino CMOS logic circuit family finds a wide variety of applications in microprocessors, digital signal processors, and dynamic memory due to their high speed and low device count. However, there are inevitable problems that degrade the noise immunity of this family; they are the inevitable leakage current and the charge sharing. Added to the drawbacks is the relatively large power consumption, especially if compared to the static complementary CMOS logic family. To make the matter worse, these drawbacks are more tactile with the scaling of CMOS technology. In my thesis, An introduction to domino logic, The impact of CMOS technology scaling on the performance of domino CMOS logic, Three Phase Domino Logic Circuit, High-performance noise-tolerant circuit techniques for CMOS dynamic logic and other Domino logic techniques are studied and corresponding Domino logic techniques have been designed and simulated. Specifically, the need to decrease the dynamic power consumption forces the designer to use a lower power-supply voltage. This in turn necessitates the reduction of threshold voltage to maintain the performance with the associated increase in sub threshold leakage current. So, a properly sized PMOS keeper must be used to compensate for this leakage. It will be found that the speed, which is the major advantage of domino logic compared to other logic styles, will degrade with CMOS technology scaling due to the contention current of the keeper. To assure high performance in noise tolerant techniques, the inevitable effects like leakage currents and charge distribution have to be minimized. In this thesis few modifications have also been made to already existing domino techniques and different Domino logic circuits are simulated in both Cadence virtuoso (implemented using GPDK090- library of 90nm technology) and Mentor graphics (implemented at different technologies like Tsmc 035.mod, Tsmc 025.mod, Tsmc 018.mod) environments. The performance parameters are also compared with other standard architectures of Domino logic

REVIEW OF HIGH-SPEED DIGITAL CMOS CIRCUITS

This paper presents a comprehensive review of the major state-of-the-art high-speed CMOS digital circuits. Focusing in particular on dynamic circuits such as conventional DOMINO, conditionalevaluation DOMINO and contention-free DOMINO. Also some high-performance non-dynamic (static) circuit techniques will be reviewed such as dual-threshold (DVT) circuits. The relative performance of these circuits in terms of speed, power, and noise margins is presented. Also the effects of technology scaling into the deep sub-micron regime on these techniques are evaluated and presented

Energy Efficient Design for Deep Sub-micron CMOS VLSIs

Over the past decade, low power, energy efficient VLSI design has been the focal point of active research and development. The rapid technology scaling, the growing integration capacity, and the mounting active and leakage power dissipation are contributing to the growing complexity of modern VLSI design. Careful power planning on all design levels is required. This dissertation tackles the low-power, low-energy challenges in deep sub-micron technologies on the architecture and circuit levels. Voltage scaling is one of the most efficient ways for reducing power and energy. For ultra-low voltage operation, a new circuit technique which allows bulk CMOS circuits to work in the sub-0. 5V supply territory is presented. The threshold voltage of the slow PMOS transistor is controlled dynamically to get a lower threshold voltage during the active mode. Due to the reduced threshold voltage, switching speed becomes faster while active leakage current is increased. A technique to dynamically manage active leakage current is presented. Energy reduction resulting from using the proposed structure is demonstrated through simulations of different circuits with different levels of complexity. As technology scales, the mounting leakage current and degraded noise immunity impact performance especially that of high performance dynamic circuits. Dual threshold technology shows a good potential for leakage reduction while meeting performance goals. A model for optimally selecting threshold voltages and transistor sizes in wide fan-in dynamic circuits is presented. On the circuit level, a novel circuit level technique which handles the trade-off between noise immunity and energy dissipation for wide fan-in dynamic circuits is presented. Energy efficiency of the proposed wide fan-in dynamic circuit is further enhanced through efficient low voltage operation. Another direct consequence of technology scaling is the growing impact of interconnect parasitics and process variations on performance. Traditionally, worst case process, parasitics, and environmental conditions are considered. Designing for worst case guarantees a fail-safe operation but requires a large delay and voltage margins. This large margin can be recovered if the design can adapt to the actual silicon conditions. Dynamic voltage scaling is considered a key enabler in reducing such margin. An on-chip process identifier to recover the margin required due to process variations is described. The proposed architecture adjusts supply voltage using a hybrid between the one-time voltage setting and the continuous monitoring modes of operation. The interconnect impact on delay is minimized through a novel adaptive voltage scaling architecture. The proposed system recovers the large delay and voltage margins required by conventional systems by closely tracking the actual critical path at anytime. By tracking the actual critical path, the proposed system is robust and more energy efficient compared to both the conventional open-loop and closed-loop systems

Design and Analysis of Improved Domino Logic with Noise Tolerance and High Performance

The demands of upcoming computing, as well as the challenges of nanometer-era of VLSI design necessitate new digital logic techniques and styles that are at the same time high performance, energy efficient and robust to noise and variation. Dynamic CMOS logic gates are broadly used to design high performance circuits due to their high speed. Conversely, the vital demerit of dynamic logic style is its high noise sensitivity. The main reason for this is the sub-threshold leakage current flowing through the pull down network. With continuous technology scaling, this problem is getting more and more severe. In this thesis, a new noise tolerant dynamic CMOS circuit technique is proposed. In the proposed work, we have enhanced the behavior of the domino CMOS logic. This technique also gets benefit in terms of delay and power. This thesis describes the new low power, noise tolerant and high speed domino logic technique and presents a comparison result of this logic with previously reported schemes. Simulation results prove that, in 180 nm CMOS technology when we used this logic style to realize wide fan-in logic gates, it could achieve maximum level of noise robustness as compared to its basic counterpart. In addition, the logic also works efficiently with sequential circuits. The feasibility of this new technique is demonstrated by means of a real hardware, we have built a custom test-chip in the UMC 180 nm process technology with an ALU core, using the proposed domino logic style for each design block. In this thesis, we have also described the design and implementation of this chip. In addition to this, we have also presented initial power and delay performance comparisons between the circuit level simulated ALU and test-chip implemented in the proposed domino logic style. Finally we conclude that, the thesis contributes a very efficient logic style for wide fan-in gates, which is not only noise robust but also energy efficient and high speed

Optimal digital system design in deep submicron technology

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2006.Includes bibliographical references (p. 165-174).The optimization of a digital system in deep submicron technology should be done with two basic principles: energy waste reduction and energy-delay tradeoff. Increased energy resources obtained through energy waste reduction are utilized through energy-delay tradeoffs. The previous practice of obliviously pursuing performance has led to the rapid increase in energy consumption. While energy waste due to unnecessary switching could be reduced with small increases in logic complexity, leakage energy waste still remains as a major design challenge. We find that fine-grain dynamic leakage reduction (FG-DLR), turning off small subblocks for short idle intervals, is the key for successful leakage energy saving. We introduce an FG-DLR circuit technique, Leakage Biasing, which uses leakage currents themselves to bias the circuit into the minimum leakage state, and apply it to primary SRAM arrays for bitline leakage reduction (Leakage-Biased Bitlines) and to domino logic (Leakage-Biased Domino). We also introduce another FG-DLR circuit technique, Dynamic Resizing, which dynamically downsizes transistors on idle paths while maintaining the performance along active critical paths, and apply it to static CMOS circuits.(cont.) We show that significant energy reduction can be achieved at the same computation throughput and communication bandwidth by pipelining logic gates and wires. We find that energy saved by pipelining datapaths is eventually limited by latch energy overhead, leading to a power-optimal pipelining. Structuring global wires into on-chip networks provides a better environment for pipelining and leakage energy saving. We show that the energy-efficiency increase through replacement with dynamically packet-routed networks is bounded by router energy overhead. Finally, we provide a way of relaxing the peak power constraint. We evaluate the use of Activity Migration (AM) for hot spot removal. AM spreads heat by transporting computation to a different location on the die. We show that AM can be used either to increase the power that can be dissipated by a given package, or to lower the operating temperature and hence the operating energy.by Seongmoo Heo.Ph.D

High-Performance, Energy-Efficient CMOS Arithmetic Circuits

In a modern microprocessor, datapath/arithmetic circuits have always been an important building block in delivering high-performance, energy-efficient computing, because arithmetic operations such as addition and binary number comparison are two of the most commonly used computing instructions. Besides the manufacturing CMOS process, the two most critical design considerations for arithmetic circuits are the logic style and micro-architecture. In this thesis, a constant-delay (CD) logic style is proposed targeting full-custom high-speed applications. The constant delay characteristic of this logic style (regardless of the logic type) makes it suitable for implementing complicated logic expressions such as addition. CD logic exhibits a unique characteristic where the output is pre-evaluated before the inputs from the preceding stage are ready. This feature enables a performance advantage over static and dynamic domino logic styles in a single cycle, multi-stage circuit block. Several design considerations including timing window width adjustment and clock distribution are discussed. Using a 65-nm general-purpose CMOS technology, the proposed logic style demonstrates an average speedup of 94% and 56% over static and dynamic domino logic, respectively, in five different logic gates. Simulation results of 8-bit ripple carry adders conclude that CD logic is 39% and 23% faster than the static and dynamic-based adders, respectively. CD logic also demonstrates 39% speedup and 64% (22%) energy-delay product reduction from static logic at 100% (10%) data activity in 32-bit carry lookahead adders. To confirm CD logic's potential, a 148 ps, single-cycle 64-bit adder with CD logic implemented in the critical path is fabricated in a 65-nm, 1-V CMOS process. A new 64-bit Ling adder micro-architecture, which utilizes both inversion and absorption properties to minimize the number of CD logic and the number of logic stage in the critical path, is also proposed. At 1-V supply, this adder's measured worst-case power and leakage power are 135 mW and 0.22 mW, respectively. A single-cycle 64-bit binary comparator utilizing a radix-2 tree structure is also proposed. This comparator architecture is specifically designed for static logic to achieve both low-power and high-performance operation, especially in low input data activity environments. At 65-nm technology with 25% (10%) data activity, the proposed design demonstrates 2.3x (3.5x) and 3.7x (5.8x) power and energy-delay product efficiency, respectively. This comparator is also 2.7x faster at iso-energy (80 fJ) or 3.3x more energy-efficient at iso-delay (200 ps) than existing designs. An improved comparator, where CD logic is utilized in the critical path to achieve high performance without sacrificing the overall energy efficiency, is also realized in a 65-nm 1-V CMOS process. At 1-V supply, the proposed comparator's measured delay is 167 ps, and has an average power and a leakage power of 2.34 mW and 0.06 mW, respectively. At 0.3-pJ iso-energy or 250-ps iso-delay budget, the proposed comparator with CD logic is 20% faster or 17% more energy-efficient compared to a comparator implemented with just the static logic

Minimizing and exploiting leakage in VLSI

Power consumption of VLSI (Very Large Scale Integrated) circuits has been growing at an alarmingly rapid rate. This increase in power consumption, coupled with the increasing demand for portable/hand-held electronics, has made power consumption a dominant concern in the design of VLSI circuits today. Traditionally dynamic (switching) power has dominated the total power consumption of VLSI circuits. However, due to process scaling trends, leakage power has now become a major component of the total power consumption in VLSI circuits. This dissertation explores techniques to reduce leakage, as well as techniques to exploit leakage currents through the use of sub-threshold circuits. This dissertation consists of two studies. In the first study, techniques to reduce leakage are presented. These include a low leakage ASIC design methodology that uses high VT sleep transistors selectively, a methodology that combines input vector control and circuit modification, and a scheme to find the optimum reverse body bias voltage to minimize leakage. As the minimum feature size of VLSI fabrication processes continues to shrink with each successive process generation (along with the value of supply voltage and therefore the threshold voltage of the devices), leakage currents increase exponentially. Leakage currents are hence seen as a necessary evil in traditional VLSI design methodologies. We present an approach to turn this problem into an opportunity. In the second study in this dissertation, we attempt to exploit leakage currents to perform computation. We use sub-threshold digital circuits and come up with ways to get around some of the pitfalls associated with sub-threshold circuit design. These include a technique that uses body biasing adaptively to compensate for Process, Voltage and Temperature (PVT) variations, a design approach that uses asynchronous micro-pipelined Network of Programmable Logic Arrays (NPLAs) to help improve the throughput of sub-threshold designs, and a method to find the optimum supply voltage that minimizes energy consumption in a circuit

A Structured Design Methodology for High Performance VLSI Arrays

abstract: The geometric growth in the integrated circuit technology due to transistor scaling also with system-on-chip design strategy, the complexity of the integrated circuit has increased manifold. Short time to market with high reliability and performance is one of the most competitive challenges. Both custom and ASIC design methodologies have evolved over the time to cope with this but the high manual labor in custom and statistic design in ASIC are still causes of concern. This work proposes a new circuit design strategy that focuses mostly on arrayed structures like TLB, RF, Cache, IPCAM etc. that reduces the manual effort to a great extent and also makes the design regular, repetitive still achieving high performance. The method proposes making the complete design custom schematic but using the standard cells. This requires adding some custom cells to the already exhaustive library to optimize the design for performance. Once schematic is finalized, the designer places these standard cells in a spreadsheet, placing closely the cells in the critical paths. A Perl script then generates Cadence Encounter compatible placement file. The design is then routed in Encounter. Since designer is the best judge of the circuit architecture, placement by the designer will allow achieve most optimal design. Several designs like IPCAM, issue logic, TLB, RF and Cache designs were carried out and the performance were compared against the fully custom and ASIC flow. The TLB, RF and Cache were the part of the HEMES microprocessor.Dissertation/ThesisPh.D. Electrical Engineering 201