Wirelessly Powered Backscatter Communication Networks: Modeling, Coverage and Capacity

Future Internet-of-Things (IoT) will connect billions of small computing devices embedded in the environment and support their device-to-device (D2D) communication. Powering this massive number of embedded devices is a key challenge of designing IoT since batteries increase the devices' form factors and battery recharging/replacement is difficult. To tackle this challenge, we propose a novel network architecture that enables D2D communication between passive nodes by integrating wireless power transfer and backscatter communication, which is called a wirelessly powered backscatter communication (WP-BackCom) network. In the network, standalone power beacons (PBs) are deployed for wirelessly powering nodes by beaming unmodulated carrier signals to targeted nodes. Provisioned with a backscatter antenna, a node transmits data to an intended receiver by modulating and reflecting a fraction of a carrier signal. Such transmission by backscatter consumes orders-of-magnitude less power than a traditional radio. Thereby, the dense deployment of low-complexity PBs with high transmission power can power a large-scale IoT. In this paper, a WP-BackCom network is modeled as a random Poisson cluster process in the horizontal plane where PBs are Poisson distributed and active ad-hoc pairs of backscatter communication nodes with fixed separation distances form random clusters centered at PBs. The backscatter nodes can harvest energy from and backscatter carrier signals transmitted by PBs. Furthermore, the transmission power of each node depends on the distance from the associated PB. Applying stochastic geometry, the network coverage probability and transmission capacity are derived and optimized as functions of backscatter parameters, including backscatter duty cycle and reflection coefficient, as well as the PB density. The effects of the parameters on network performance are characterized.Comment: 28 pages, 11 figures, has been submitted to IEEE Trans. on Wireless Communicatio

Adaptive and Probabilistic Power Control Algorithms for Dense RFID Reader Network

In radio frequency identification (RFID) systems, the detection range and read rates may suffer from interferences between high power devices such as readers. In dense networks, this problem grows severely and degrades system performance. In this paper, we investigate feasible power control schemes to ensure overall coverage area of the system while maintaining a desired data rate. The power control should dynamically adjust the output power of a RFID reader by adapting to the noise level seen during tag reading and acceptable signal-to-noise ratio (SNR). We present a novel distributed adaptive power control (DAPC) and probabilistic power control (PPC) as two possible solutions. This paper discusses the methodology and implementation of both algorithms analytically. Both DAPC and PPC scheme are simulated, compared and discussed for further work

Decentralized Power Control with Implementation for RFID Networks

In radio frequency identification (RFID) systems, the detection range and read rates will suffer from interference among high power reading devices. This problem grows severely and degrades system performance in dense RFID networks. In this paper, we investigate a suite of feasible power control schemes to ensure overall coverage area of the system while maintaining a desired read rate. The power control scheme and MAC protocol dynamically adjusts the RFID reader power output in response to the interference level seen locally during tag reading for an acceptable signal-to-noise ratio (SNR). We present novel distributed adaptive power control (DAPC) and probabilistic power control (PPC) as two possible solutions. A generic UHF wireless testbed is built using UMR/SLU GEN4-SSN for implementng the protocol. Simulation and hardware results are included

Goodbye, ALOHA!

©2016 IEEE. Personal use of this material is permitted. Permission from IEEE must be obtained for all other uses, in any current or future media, including reprinting/republishing this material for advertising or promotional purposes, creating new collective works, for resale or redistribution to servers or lists, or reuse of any copyrighted component of this work in other works.The vision of the Internet of Things (IoT) to interconnect and Internet-connect everyday people, objects, and machines poses new challenges in the design of wireless communication networks. The design of medium access control (MAC) protocols has been traditionally an intense area of research due to their high impact on the overall performance of wireless communications. The majority of research activities in this field deal with different variations of protocols somehow based on ALOHA, either with or without listen before talk, i.e., carrier sensing multiple access. These protocols operate well under low traffic loads and low number of simultaneous devices. However, they suffer from congestion as the traffic load and the number of devices increase. For this reason, unless revisited, the MAC layer can become a bottleneck for the success of the IoT. In this paper, we provide an overview of the existing MAC solutions for the IoT, describing current limitations and envisioned challenges for the near future. Motivated by those, we identify a family of simple algorithms based on distributed queueing (DQ), which can operate for an infinite number of devices generating any traffic load and pattern. A description of the DQ mechanism is provided and most relevant existing studies of DQ applied in different scenarios are described in this paper. In addition, we provide a novel performance evaluation of DQ when applied for the IoT. Finally, a description of the very first demo of DQ for its use in the IoT is also included in this paper.Peer ReviewedPostprint (author's final draft

Adaptive and Probabilistic Power Control Algorithms for RFID Reader Networks

In radio frequency identification (RFID) systems, the detection range and read rates will suffer from interference among high power reading devices. This problem grows severely and degrades system performance in dense RFID networks. Consequently, medium access protocols (MAC) protocols are needed for such networks to assess and provide access to the channel so that tags can be read accurately. In this paper, we investigate a suite of feasible power control schemes to ensure overall coverage area of the system while maintaining a desired read rate. The power control scheme and MAC protocol dynamically adjusts the RFID reader power output in response to the interference level seen during tag reading and acceptable signal-to-noise ratio (SNR). We present novel distributed adaptive power control (DAPC) and probabilistic power control (PPC) as two possible solutions. A suitable back off scheme is also added with DAPC to improve coverage. Both the methodology and implementation of the schemes are presented, simulated, compared, and discussed for further work

Adaptive Power Control Protocol with Hardware Implementation for Wireless Sensor and RFID Reader Networks

The development and deployment of radio frequency identification (RFID) systems render a novel distributed sensor network which enhances visibility into manufacturing processes. In RFID systems, the detection range and read rates will suffer from interference among high-power reading devices. This problem grows severely and degrades system performance in dense RFID networks. Consequently, medium access protocols (MAC) protocols are needed for such networks to assess and provide access to the channel so that tags can be read accurately. In this paper, we investigate a suite of feasible power control schemes to ensure overall coverage area of the system while maintaining a desired read rate. The power control scheme and MAC protocol dynamically adjust the RFID reader power output in response to the interference level seen during tag reading and acceptable signal-to-noise ratio (SNR). We present novel distributed adaptive power control (DAPC) as a possible solution. A suitable back off scheme is also added with DAPC to improve coverage. A generic UHF wireless testbed is built using UMR/SLU GEN4-SSN for implementing the protocol. Both the methodology and hardware implementation of the schemes are presented, compared, and discussed. The results of hardware implementation illustrate that the protocol performs satisfactorily as expected

Indoor wireless communications and applications

Chapter 3 addresses challenges in radio link and system design in indoor scenarios. Given the fact that most human activities take place in indoor environments, the need for supporting ubiquitous indoor data connectivity and location/tracking service becomes even more important than in the previous decades. Specific technical challenges addressed in this section are(i), modelling complex indoor radio channels for effective antenna deployment, (ii), potential of millimeter-wave (mm-wave) radios for supporting higher data rates, and (iii), feasible indoor localisation and tracking techniques, which are summarised in three dedicated sections of this chapter

Interference sources in congested environments and its effects in UHF-RFID systems : a review

In scenario where radio frequency identification (RFID) readers become increasingly common in hand held devices, the radios are prone to several interferences not only from external radio sources but also from the plurality of portable devices that may become more common over time. For that reason it is of interest to well understand how these radio interferences may be influencing a UHF-RFID transceiver working according to EPCglobal Class-1 Gen-2. In particular, in this paper, the combination of interference coming from the self-radio, from other radio systems, such as mobile phone or other RFID reader, is analyzed, and such effects are combined with the appearance of multiple tag antennas interfering each other. A method based on simulation using tag antenna design is presented to evaluate inter-tag interference in a variety of cases. For a better understanding analytic examples are presented to compute such interference interactions within the RFID system