Deliverable D4.1: VLC modulation schemes

This report presents the analysis of different modulation schemes D4.1 for VLC systems of the VIDAS project. Considering the final prototype design and application, the deliverable D4.1 was projected. The detail analysis of various modulation schemes are carried out and a robust technique based on direct sequence spread spectrum (DSSS) is followed. DSSS technique though necessitates use of high bandwidth while minimizing the effect of noise. Since the final application does not require very high dat a rate of transmission but robustness against the noise (external lights) becomes necessary. The analysis is followed by model development using Matlab/Simulink. The performance of both of these systems are compared and evaluated. Some of the simulation results are presented

An Ultra-Low-Power Track-and-Hold Amplifier

The future of electronics is the Internet of Things (IoT) paradigm, where always-on devices and sensors monitor and transform everyday life. A plethora of applications (such as navigating drivers past road hazards or monitoring bridge and building stresses) employ this technology. These unattended ground-sensor applications require decade(s)-long operational life-times without battery changes. Such electronics demand stringent performance specifications with only nano-Watt power levels.This thesis presents an ultra-low-power track-and-hold amplifier for such systems. It serves as the front-end of a SAR-ADC or the building block for equalizers or filters. This amplifier\u27s design attains exceptional hold times by mitigating switch subthreshold leakage and bulk leakage. Its novel transmission-gate topology achieves wide-swing performance. Though only consuming 100 pico-Watts, it achieves a precision of 7.6 effective number of bits (ENOB). The track-and-hold amplifier was designed in 130-nm CMOS

ANALYSIS OF MOS CURRENT MODE LOGIC (MCML) AND IMPLEMENTATION OF MCML STANDARD CELL LIBRARY FOR LOW-NOISE DIGITAL CIRCUIT DESIGN

MOS current mode logic (MCML) offers low noise digital circuits that reduce noise that can cripple analog components in mixed-signal integrated circuits, when compared to CMOS digital circuits. An MCML standard cell library was developed for the Cadence Virtuoso Integrated Circuit (IC) design software that gives IC designers the ability to design complex, low noise digital circuits for use in mixed-signal and noise sensitive systems at a high level of abstraction, allowing them to get superior products to market faster than competitors. The MCML standard cell library developed and presented here allows for fast development of mixed signal circuits by providing quiet digital building block gates that reduce the simultaneous switching noise (SSN) by an order of magnitude over conventional CMOS based designs [3]. This thesis project developed the following digital gates in MCML as a standard cell library for general-purpose low noise and very low noise applications: inverter, buffer, NAND, AND, NOR, OR, XOR, NXOR, 2:1 MUX, CMOS to MCML, MCML to CMOS, and double edge triggered flip-flop (DETFF)

A Novel variation-tolerant 9T SRAM design for nanoscale CMOS

As the feature sizes decrease, understanding manufacturing variations becomes essential to effectively design robust circuits. Manufacturing variations occur when process parameters deviate from their ideal or expected values, resulting in variations in device characteristics. Variations in the device characteristics cause the circuit to deviate from its expected behavior resulting in circuit instability, performance degradation, and yield loss. Both from an economic and performance standpoint, the yield and performance of Static Random Access Memories (SRAMs) are of great importance to the modern System-on-Chip designs. SRAM bitcells typically employ well-matched, minimum-sized transistors which make them highly sensitive to process variations. To overcome these challenges, researchers have proposed different topologies for SRAMs with 8T and 10T SRAM designs. These designs improve the cell stability but suffer from bitline-leakage noise, placing constraints on the number of cells shared by each bitline. These designs also have substantial area overhead when compared to the traditional 6T design. In this work, the published SRAM designs are characterized using commercial CMOS 65 nm models and are compared based on critical SRAM parameters like read stability, write stability, bitline leakage and the impact of process variations. Furthermore, a single-ended 9T SRAM design is proposed that enhances data stability and simultaneously addresses the bitline leakage problem. The proposed design also satisfies the yield criterion to achieve 90% yield for a 1Mb SRAM array in the presence of process variations

A novel deep submicron bulk planar sizing strategy for low energy subthreshold standard cell libraries

Engineering andPhysical Science ResearchCouncil (EPSRC) and Arm Ltd for providing funding in the form of grants and studentshipsThis work investigates bulk planar deep submicron semiconductor physics in an attempt to improve standard cell libraries aimed at operation in the subthreshold regime and in Ultra Wide Dynamic Voltage Scaling schemes. The current state of research in the field is examined, with particular emphasis on how subthreshold physical effects degrade robustness, variability and performance. How prevalent these physical effects are in a commercial 65nm library is then investigated by extensive modeling of a BSIM4.5 compact model. Three distinct sizing strategies emerge, cells of each strategy are laid out and post-layout parasitically extracted models simulated to determine the advantages/disadvantages of each. Full custom ring oscillators are designed and manufactured. Measured results reveal a close correlation with the simulated results, with frequency improvements of up to 2.75X/2.43X obs erved for RVT/LVT devices respectively. The experiment provides the first silicon evidence of the improvement capability of the Inverse Narrow Width Effect over a wide supply voltage range, as well as a mechanism of additional temperature stability in the subthreshold regime. A novel sizing strategy is proposed and pursued to determine whether it is able to produce a superior complex circuit design using a commercial digital synthesis flow. Two 128 bit AES cores are synthesized from the novel sizing strategy and compared against a third AES core synthesized from a state-of-the-art subthreshold standard cell library used by ARM. Results show improvements in energy-per-cycle of up to 27.3% and frequency improvements of up to 10.25X. The novel subthreshold sizing strategy proves superior over a temperature range of 0 °C to 85 °C with a nominal (20 °C) improvement in energy-per-cycle of 24% and frequency improvement of 8.65X. A comparison to prior art is then performed. Valid cases are presented where the proposed sizing strategy would be a candidate to produce superior subthreshold circuits

A Structured Design Methodology for High Performance VLSI Arrays

abstract: The geometric growth in the integrated circuit technology due to transistor scaling also with system-on-chip design strategy, the complexity of the integrated circuit has increased manifold. Short time to market with high reliability and performance is one of the most competitive challenges. Both custom and ASIC design methodologies have evolved over the time to cope with this but the high manual labor in custom and statistic design in ASIC are still causes of concern. This work proposes a new circuit design strategy that focuses mostly on arrayed structures like TLB, RF, Cache, IPCAM etc. that reduces the manual effort to a great extent and also makes the design regular, repetitive still achieving high performance. The method proposes making the complete design custom schematic but using the standard cells. This requires adding some custom cells to the already exhaustive library to optimize the design for performance. Once schematic is finalized, the designer places these standard cells in a spreadsheet, placing closely the cells in the critical paths. A Perl script then generates Cadence Encounter compatible placement file. The design is then routed in Encounter. Since designer is the best judge of the circuit architecture, placement by the designer will allow achieve most optimal design. Several designs like IPCAM, issue logic, TLB, RF and Cache designs were carried out and the performance were compared against the fully custom and ASIC flow. The TLB, RF and Cache were the part of the HEMES microprocessor.Dissertation/ThesisPh.D. Electrical Engineering 201

Variability-Aware VLSI Design Automation For Nanoscale Technologies

As technology scaling enters the nanometer regime, design of large scale ICs gets more challenging due to shrinking feature sizes and increasing design complexity. Aggressive scaling causes significant degradation in reliability, increased susceptibility to fabrication and environmental randomness and increased dynamic and leakage power dissipation. In this work, we investigate these scaling issues in large scale integrated systems. This dissertation proposes to develop variability-aware design methodologies by proposing design analysis, design-time optimization, post-silicon tunability and runtime-adaptivity based optimization techniques for handling variability. We discuss our research in the area of variability-aware analysis, specifically focusing on the problem of statistical timing analysis. The first technique presents the concept of error budgeting that achieves significant runtime speedups during statistical timing analysis. The second work presents a general framework for non-linear non-Gaussian statistical timing analysis considering correlations. Further, we present our work on design-time optimization schemes that are applicable during physical synthesis. Firstly, we present a buffer insertion technique that considers wire-length uncertainty and proposes algorithms to perform probabilistic buffer insertion. Secondly, we present a stochastic optimization framework based on Monte-Carlo technique considering fabrication variability. This optimization framework can be applied to problems that can be modeled as linear programs without without imposing any assumptions on the nature of the variability. Subsequently, we present our work on post-silicon tunability based design optimization. This work presents a design management framework that can be used to balance the effort spent on pre-silicon (through gate sizing) and post-silicon optimization (through tunable clock-tree buffers) while maximizing the yield gains. Lastly, we present our work on variability-aware runtime optimization techniques. We look at the problem of runtime supply voltage scaling for dynamic power optimization, and propose a framework to consider the impact of variability on the reliability of such designs. We propose a probabilistic design synthesis technique where reliability of the design is a primary optimization metric

Algorithmic techniques for nanometer VLSI design and manufacturing closure

As Very Large Scale Integration (VLSI) technology moves to the nanoscale regime, design and manufacturing closure becomes very difficult to achieve due to increasing chip and power density. Imperfections due to process, voltage and temperature variations aggravate the problem. Uncertainty in electrical characteristic of individual device and wire may cause significant performance deviations or even functional failures. These impose tremendous challenges to the continuation of Moore's law as well as the growth of semiconductor industry. Efforts are needed in both deterministic design stage and variation-aware design stage. This research proposes various innovative algorithms to address both stages for obtaining a design with high frequency, low power and high robustness. For deterministic optimizations, new buffer insertion and gate sizing techniques are proposed. For variation-aware optimizations, new lithography-driven and post-silicon tuning-driven design techniques are proposed. For buffer insertion, a new slew buffering formulation is presented and is proved to be NP-hard. Despite this, a highly efficient algorithm which runs > 90x faster than the best alternatives is proposed. The algorithm is also extended to handle continuous buffer locations and blockages. For gate sizing, a new algorithm is proposed to handle discrete gate library in contrast to unrealistic continuous gate library assumed by most existing algorithms. Our approach is a continuous solution guided dynamic programming approach, which integrates the high solution quality of dynamic programming with the short runtime of rounding continuous solution. For lithography-driven optimization, the problem of cell placement considering manufacturability is studied. Three algorithms are proposed to handle cell flipping and relocation. They are based on dynamic programming and graph theoretic approaches, and can provide different tradeoff between variation reduction and wire- length increase. For post-silicon tuning-driven optimization, the problem of unified adaptivity optimization on logical and clock signal tuning is studied, which enables us to significantly save resources. The new algorithm is based on a novel linear programming formulation which is solved by an advanced robust linear programming technique. The continuous solution is then discretized using binary search accelerated dynamic programming, batch based optimization, and Latin Hypercube sampling based fast simulation

Elastic bundles :modelling and architecting asynchronous circuits with granular rigidity

PhD ThesisIntegrated Circuit (IC) designs these days are predominantly System-on-Chips (SoCs). The complexity of designing a SoC has increased rapidly over the years due to growing process and environmental variations coupled with global clock distribution di culty. Moreover, traditional synchronous design is not apt to handle the heterogeneous timing nature of modern SoCs. As a countermeasure, the semiconductor industry witnessed a strong revival of asynchronous design principles. A new paradigm of digital circuits emerged, as a result, namely mixed synchronous-asynchronous circuits. With a wave of recent innovations in synchronous-asynchronous CAD integration, this paradigm is showing signs of commercial adoption in future SoCs mainly due to the scope for reuse of synchronous functional blocks and IP cores, and the co-existence of synchronous and asynchronous design styles in a common EDA framework. However, there is a lack of formal methods and tools to facilitate mixed synchronousasynchronous design. In this thesis, we propose a formal model based on Petri nets with step semantics to describe these circuits behaviourally. Implication of this model in the veri cation and synthesis of mixed synchronous-asynchronous circuits is studied. Till date, this paradigm has been mainly explored on the basis of Globally Asynchronous Locally Synchronous (GALS) systems. Despite decades of research, GALS design has failed to gain traction commercially. To understand its drawbacks, a simulation framework characterising the physical and functional aspects of GALS SoCs is presented. A novel method for synthesising mixed synchronous-asynchronous circuits with varying levels of rigidity is proposed. Starting with a high-level data ow model of a system which is intrinsically asynchronous, the key idea is to introduce rigidity of chosen granularity levels in the model without changing functional behaviour. The system is then partitioned into functional blocks of synchronous and asynchronous elements before being transformed into an equivalent circuit which can be synthesised using standard EDA tools