Optical Space Division Multiplexing in Short Reach Multi-Mode Fiber Systems

The application of space division multiplexing to fiber-optic communications is a promising approach to further increase the channel capacity of optical waveguides. In this work, short reach and low-cost optical space division multiplexing systems with intensity modulation and direct detection (IM/DD) are in the focus of interest. Herein, different modes are utilized to generate spatial diversity in a multi-mode fiber. In such IM/DD systems, the process of square-law detection is inherently non-linear. In order to obtain an understanding of the channel characteristics, a system model is developed, which is able to show under which conditions the system can be considered linear in baseband. It is shown that linearity applies in scenarios with low mode cross-talk. This enables the use of linear multiple-input multiple-output (MIMO) signal processing strategies for equalization purposes. In conditions with high mode cross-talk, significant interference occurs, and the transmitted information cannot be extracted at the receiver. Furthermore, a method to determine the power coupling coefficients between mode groups is presented that does not require the excitation of individual modes, and hence it can be realized with inexpensive components. In addition, different optical components are analyzed with respect for their suitability in MIMO setups with IM/DD. The conventional approach with single-mode fiber to multi-mode fiber offset launches and optical couplers as well as a configuration that utilizes multi-segment detection are feasible options for a (2x2) setup. It is further shown that conventional photonic lanterns are not suited for MIMO with IM/DD due to their low mode orthogonality during the multiplexing process. In order to enable higher order MIMO configurations, devices for mode multiplexing and demultiplexing need to be developed, which exhibit a high mode orthogonality on one hand and are low-cost on the other hand

Assessment of the Performance of Inverse Class-F Power Amplifiers in a Discrete Doherty Architecture

This work presents an assessment, at simulation and experimental levels, of the performance of inverse class-F power amplifiers in a Doherty architecture. Two connectorized amplifier modules, designed for standalone operation, are adopted to construct a quasi-balanced Doherty architecture exploiting 3-dB 90° hybrid couplers at the input and output to demonstrate the concept. The Doherty architecture shows competitive performance at 1.8 GHz, with 43 dBm output power and around 60% efficiency from saturation to 6 dB output power back-off. The performance is in line with the state of the art of integrated load-modulated amplifiers, demonstrating the validity of the approach

Characterization and Emulation of Low-Voltage Power Line Channels for Narrowband and Broadband Communication

The demand for smart grid and smart home applications has raised the recent interest in power line communication (PLC) technologies, and has driven a broad set of deep surveys in low-voltage (LV) power line channels. This book proposes a set of novel approaches, to characterize and to emulate LV power line channels in the frequency range from0.15to 10 MHz, which closes gaps between the traditional narrowband (up to 500 kHz) and broadband (above1.8 MHz) ranges

Characterization and Emulation of Low-Voltage Power Line Channels for Narrowband and Broadband Communication

The demand for smart grid and smart home applications has raised the recent interest in power line communication (PLC) technologies, and has driven a broad set of deep surveys in low-voltage (LV) power line channels. This book proposes a set of novel approaches, to characterize and to emulate LV power line channels in the frequency range from0.15to 10 MHz, which closes gaps between the traditional narrowband (up to 500 kHz) and broadband (above1.8 MHz) ranges

Automatic Tuning of Silicon Photonics Millimeter-Wave Transceivers Building Blocks

Today, continuously growing wireless traffic have guided the progress in the wireless communication systems. Now, evolution towards next generation (5G) wireless communication systems are actively researched to accommodate expanding future data traffic. As one of the most promising candidates, integrating photonic devices in to the existing wireless system is considered to improve the performance of the systems. Emerging silicon photonic integrated circuits lead this integration more practically, and open new possibilities to the future communication systems. In this dissertation, the development of the electrical wireless communication systems are briefly explained. Also, development of the microwave photonics and silicon photonics are described to understand the possibility of the hybrid SiP integrated wireless communication systems. A limitation of the current electrical wireless systems are addressed, and hybrid integrated mm-wave silicon photonic receiver, and silicon photonic beamforming transmitter are proposed and analyzed in system level. In the proposed mm-wave silicon photonic receiver has 4th order pole-zero silicon photonic filter in the system. Photonic devices are vulnerable to the process and temperature variations. It requires manual calibration, which is expensive, time consuming, and prone to human errors. Therefore, precise automatic calibration solution with modified silicon photonic filter structure is proposed and demonstrated. This dissertation demonstrates fully automatic tuning of silicon photonic all-pass filter (APF)-based pole/zero filters using a monitor-based tuning method that calibrates the initial response by controlling each pole and zero individually via micro-heaters. The proposed tuning approach calibrates severely degraded initial responses to the designed elliptic filter shapes and allows for automatic bandwidth and center frequency reconfiguration of these filters. This algorithm is demonstrated on 2nd- and 4th-order filters fabricated in a standard silicon photonics foundry process. After the initial calibration, only 300ms is required to reconfigure a filter to a different center frequency. Thermal crosstalk between the micro-heaters is investigated, with substrate thinning demonstrated to suppress this effect and reduce filter calibration to less than half of the original thick substrate times. This fully automatic tuning approach opens the possibility of employing silicon photonic filters in real communication systems. Also, in the proposed beamforming transmitter, true-time delay ring resonator based 1x4 beamforming network is imbedded. A proposed monitor-based tuning method compensates fabrication variations and thermal crosstalk by controlling micro-heaters individually using electrical monitors. The proposed tuning approach successfully demonstrated calibration of OBFN from severely degraded initial responses to well-defined group delay response required for the targeted radiating angle with a range of 60◦ (-30◦ to 30◦ ) in a linear beamforming antenna array. This algorithm is demonstrated on OBFN fabricated in a standard silicon photonics foundry process. The calibrated OBFN operates at 30GHz and provide 2GHz bandwidth. This fully automatic tuning approach opens the possibility of employing silicon OBFN in real wideband mm-wave wireless communication systems by providing robust operating solutions. All the proposed photonic circuits are implemented using the standard silicon photonic technologies, and resulted in several publications in IEEE/OSA Journals and Conferences

Millimeter-Wave Components and Antennas for Spatial and Polarization Diversity using PRGW Technology

The evolution of the wireless communication systems to the future generation is accompanied by a huge improvement in the system performance through providing a high data rate with low latency. These systems require access to millimeter wave (mmWave) bands, which offer several advantages such as physically smaller components and much wider bandwidthcomparedtomicrowavefrequencies. However, mmWavecomponentsstillneed a significant improvement to follow the rapid variations in future technologies. Although mmWave frequencies can carry more data, they are limited in terms of their penetration capabilities and their coverage range. Moreover, these frequencies avoid deploying traditional guiding technologies such as microstrip lines due to high radiation and material losses. Hence, utilizing new guiding structure techniques such as Printed Ridge Gap Waveguide (PRGW) is essential in future mmWave systems implementation. ThemainpurposeofthisthesisistodesignmmWavecomponents,antennasubsystems and utilize both in beam switching systems. The major mmWave components addressed in this thesis are hybrid coupler, crossover, and differential power divider where the host guidingstructureisthePRGW.Inaddition,variousdesignsfordifferentialfeedingPRGW antennas and antenna arrays are presented featuring wide bandwidth and high gain in mmWave band. Moreover, the integration of both the proposed components and the featured antennas is introduced. This can be considered as a significant step toward the requirements fulfillment of today's advanced communication systems enabling both space and polarization diversity. The proposed components are designed to meet the future ever-increasing consumer experience and technical requirements such as low loss, compact size, and low-cost fabrication. This directed the presented research to have a contribution into three major parts. The first part highlights the feeding structures, where mmWave PRGW directional couplers and differential feeding power divider are designed and validated. These components are among the most important passive elements of microwave circuits used in antennabeam-switchingnetworks. Different3-dBquadraturehybridcouplersandcrossover prototypes are proposed, featured with a compact size and a wide bandwidth beyond 10 % at 30 GHz. In the second part, a beam switching network implemented using hybrid couplers is presented. The proposed beam switching network is a 4 × 4 PRGW Butler matrix that used to feed a Magneto-electric (ME) dipole antenna array. As a result, a 2-D scanning antenna array with a compact size, wide bandwidth, and high radiation efficiency larger than84%isachieved. Furthergainenhancementof5dBiisachievedthroughdeployinga hybridgainenhancementtechniqueincludingAMCmushroomshapesaroundtheantenna array with a dielectric superstrate located in the broadside direction. The proposed scanning antenna array can be considered as a step toward the desired improvement in the data rate and coverage through enabling the space diversity for the communication link. The final activity is related to the development of high-gain wide-band mmWave antenna arrays for potential use in future mmWave applications. The first proposed configuration is a differential feeding circular polarized aperture antenna array implemented with PRGW technology. Differential feeding antenna designs offer more advantages than single- ended antennas for mmWave communications as they are easy to be integrated with differential mmWave monolithic ICs that have high common-mode rejection ratio providing an immunity of the environmental noise. The proposed differential feeding antenna array is designed and fabricated, which featured with a stable high gain and a high radiation efficiency over a wide bandwidth. Another proposed configuration is a dualpolarized ME-dipole PRGW antenna array for mmWave wireless communication. Dual polarizationisconsideredoneofthemostimportantantennasolutionsthatcansavecosts and space for modern communication systems. In addition, it is an effective strategy for multiple-input and multiple-output systems that can reduce the size of multiple antennas systems by utilizing extra orthogonal polarization. The proposed dual- polarized antenna array is designed to achieve a stable gain of 15 ± 1 dBi with low cross- polarization less than -30 dB over a wide frequency range of 20 % at 30 GHz

Coupling for Power Line Communications: A Survey

The advent of power line communication (PLC) for smart grids, vehicular communications, internet of things and data network access has recently gained ample interest in industry and academia. Due to the characteristics of electric power grids and regulatory constraints, the effectiveness of coupling between the power line and PLC transceivers has become a very important issue. Coupling devices used to inject or extract data communication signals into or from power lines are very important components of a PLC system. There is, however, an obvious gap in the literature for a detailed review of existing PLC couplers. In this paper, we present a comprehensive review of couplers, which are required for narrowband and broadband PLC transceivers. Prevailing issues that protract the design of couplers and consequently subtended the inventions of different types of couplers are clearly described. We also provide a useful classification of PLC couplers based on the type of physical couplings, voltage levels, frequency bandwidth, propagation modes and a number of connections. This survey will guide researchers, as well as designers alike, into a quicker resourcing when studying coupling in narrowband and broadband PLC systems

WDM-compatible polarization-diverse OAM generator and multiplexer in silicon photonics

Spatial multiplexing using orbital angular momentum (OAM) modes is an efficient means of scaling up the capacity of fiber-optic communications systems; integrated multiplexers are crucial enablers of this approach. OAM modes are circularly polarized when propagating in a fiber, however, OAM generators previously demonstrated in silicon photonics use locally linearly polarized emitters. Coupling from multiplexers to fibers in those solutions results in extra loss and complexity. Moreover, many of those solutions are based on resonator structures with strong wavelength dependence, and are thus incompatible with wavelength-division multiplexing (WDM). We experimentally demonstrate on-chip generation and multiplexing of OAM modes using an array of circularly polarized 2D antennas with wide wavelength coverage. The proposed device was implemented on the standard 220-nm silicon-on-insulator platform. Optical vortex beams with OAM orders ranging from -3 to +3 in both left and right circular polarization states were generated from the same aperture across a wavelength range of 1540 nm to 1557 nm. This device could serve as a multiplexer or demultiplexer for up to 12 information bearing channels coupling into a