Robust Circuit Design for Low-Voltage VLSI.

Voltage scaling is an effective way to reduce the overall power consumption, but the major challenges in low voltage operations include performance degradation and reliability issues due to PVT variations. This dissertation discusses three key circuit components that are critical in low-voltage VLSI. Level converters must be a reliable interface between two voltage domains, but the reduced on/off-current ratio makes it extremely difficult to achieve robust conversions at low voltages. Two static designs are proposed: LC2 adopts a novel pulsed-operation and modulates its pull-up strength depending on its state. A 3-sigma robustness is guaranteed using a current margin plot; SLC inherently reduces the contention by diode-insertion. Improvements in performance, power, and robustness are measured from 130nm CMOS test chips. SRAM is a major bottleneck in voltage-scaling due to its inherent ratioed-bitcell design. The proposed 7T SRAM alleviates the area overhead incurred by 8T bitcells and provides robust operation down to 0.32V in 180nm CMOS test chips with 3.35fW/bit leakage. Auto-Shut-Off provides a 6.8x READ energy reduction, and its innate Quasi-Static READ has been demonstrated which shows a much improved READ error rate. A use of PMOS Pass-Gate improves the half-select robustness by directly modulating the device strength through bitline voltage. Clocked sequential elements, flip-flops in short, are ubiquitous in today’s digital systems. The proposed S2CFF is static, single-phase, contention-free, and has the same number of devices as in TGFF. It shows a 40% power reduction as well as robust low-voltage operations in fabricated 45nm SOI test chips. Its simple hold-time path and the 3.4x improvement in 3-sigma hold-time is presented. A new on-chip flip-flop testing harness is also proposed, and measured hold-time variations of flip-flops are presented.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/111525/1/yejoong_1.pd

Low-power and high-performance SRAM design in high variability advanced CMOS technology

As process technologies shrink, the size and number of memories on a chip are exponentially increasing. Embedded SRAMs are a critical component in modern digital systems, and they strongly impact the overall power, performance, and area. To promote memory-related research in academia, this dissertation introduces OpenRAM, a flexible, portable and open-source memory compiler and characterization methodology for generating and verifying memory designs across different technologies.In addition, SRAM designs, focusing on improving power consumption, access time and bitcell stability are explored in high variability advanced CMOS technologies. To have a stable read/write operation for SRAM in high variability process nodes, a differential-ended single-port 8T bitcell is proposed that improves the read noise margin, write noise margin and readout bitcell current by 45%, 48% and 21%, respectively, compared to a conventional 6T bitcell. Also, a differential-ended single-port 12T bitcell for subthreshold operation is proposed that solves the half-select disturbance and allows efficient bit-interleaving. 12T bitcell has a leakage control mechanism which helps to reduce the power consumption and provides operation down to 0.3 V. Both 8T and 12T bitcells are analyzed in a 64 kb SRAM array using 32 nm technology. Besides, to further improve the access time and power consumption, two tracking circuits (multi replica bitline delay and reconfigurable replica bitline delay techniques) are proposed to aid the generation of accurate and optimum sense amplifier set time.An error tolerant SRAM architecture suitable for low voltage video application with dynamic power-quality management is also proposed in this dissertation. This memory uses three power supplies to improve the SRAM stability in low voltages. The proposed triple-supply approach achieves 63% improvement in image quality and 69% reduction in power consumption compared to a single-supply 64 kb SRAM array at 0.70 V

Design techniques for dense embedded memory in advanced CMOS technologies

University of Minnesota Ph.D. dissertation. February 2012. Major: Electrical Engineering. Advisor: Chris H. Kim. 1 computer file (PDF); viii, 116 pages.On-die cache memory is a key component in advanced processors since it can boost micro-architectural level performance at a moderate power penalty. Demand for denser memories only going to increase as the number of cores in a microprocessor goes up with technology scaling. A commensurate increase in the amount of cache memory is needed to fully utilize the larger and more powerful processing units. 6T SRAMs have been the embedded memory of choice for modern microprocessors due to their logic compatibility, high speed, and refresh-free operation. However, the relatively large cell size and conflicting requirements for read and write make aggressive scaling of 6T SRAMs challenging in sub-22 nm. In this dissertation, circuit techniques and simulation methodologies are presented to demonstrate the potential of alternative options such as gain cell eDRAMs and spin-torque-transfer magnetic RAMs (STT-MRAMs) for high density embedded memories.Three unique test chip designs are presented to enhance the retention time and access speed of gain cell eDRAMs. Proposed bit-cells utilize preferential boostings, beneficial couplings, and aggregated cell leakages for expanding signal window between data `1' and `0'. The design space of power-delay product can be further enhanced with various assist schemes that harness the innate properties of gain cell eDRAMs. Experimental results from the test chips demonstrate that the proposed gain cell eDRAMs achieve overall faster system performances and lower static power dissipations than SRAMs in a generic 65 nm low-power (LP) CMOS process. A magnetic tunnel junction (MTJ) scaling scenario and an efficient HSPICE simulation methodology are proposed for exploring the scalability of STT-MRAMs under variation effects from 65 nm to 8 nm. A constant JC0*RA/VDD scaling method is adopted to achieve optimal read and write performances of STT-MRAMs and thermal stabilities for a 10 year retention are achieved by adjusting free layer thicknesses as well as projecting crystalline anisotropy improvements. Studies based on the proposed methodology show that in-plane STT-MRAM will outperform SRAM from 15 nm node, while its perpendicular counterpart requires further innovations in MTJ material properties in order to overcome the poor write performance from 22 nm node

Low energy digital circuit design using sub-threshold operation

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, February 2006.Includes bibliographical references (p. 189-202).Scaling of process technologies to deep sub-micron dimensions has made power management a significant concern for circuit designers. For emerging low power applications such as distributed micro-sensor networks or medical applications, low energy operation is the primary concern instead of speed, with the eventual goal of harvesting energy from the environment. Sub-threshold operation offers a promising solution for ultra-low-energy applications because it often achieves the minimum energy per operation. While initial explorations into sub-threshold circuits demonstrate its promise, sub-threshold circuit design remains in its infancy. This thesis makes several contributions that make sub-threshold design more accessible to circuit designers. First, a model for energy consumption in sub-threshold provides an analytical solution for the optimum VDD to minimize energy. Fitting this model to a generic circuit allows easy estimation of the impact of processing and environmental parameters on the minimum energy point. Second, analysis of device sizing for sub-threshold circuits shows the trade-offs between sizing for minimum energy and for minimum voltage operation.(cont.) A programmable FIR filter test chip fabricated in 0.18pum bulk CMOS provides measurements to confirm the model and the sizing analysis. Third, a low-overhead method for integrating sub-threshold operation with high performance applications extends dynamic voltage scaling across orders of magnitude of frequency and provides energy scalability down to the minimum energy point. A 90nm bulk CMOS test chip confirms the range of operation for ultra-dynamic voltage scaling. Finally, sub-threshold operation is extended to memories. Analysis of traditional SRAM bitcells and architectures leads to development of a new bitcell for robust sub-threshold SRAM operation. The sub-threshold SRAM is analyzed experimentally in a 65nm bulk CMOS test chip.by Benton H. Calhoun.Ph.D

Ultra Low Power Digital Circuit Design for Wireless Sensor Network Applications

Ny forskning innenfor feltet trådløse sensornettverk åpner for nye og innovative produkter og løsninger. Biomedisinske anvendelser er blant områdene med størst potensial og det investeres i dag betydelige beløp for å bruke denne teknologien for å gjøre medisinsk diagnostikk mer effektiv samtidig som man åpner for fjerndiagnostikk basert på trådløse sensornoder integrert i et ”helsenett”. Målet er å forbedre tjenestekvalitet og redusere kostnader samtidig som brukerne skal oppleve forbedret livskvalitet som følge av økt trygghet og mulighet for å tilbringe mest mulig tid i eget hjem og unngå unødvendige sykehusbesøk og innleggelser. For å gjøre dette til en realitet er man avhengige av sensorelektronikk som bruker minst mulig energi slik at man oppnår tilstrekkelig batterilevetid selv med veldig små batterier. I sin avhandling ” Ultra Low power Digital Circuit Design for Wireless Sensor Network Applications” har PhD-kandidat Farshad Moradi fokusert på nye løsninger innenfor konstruksjon av energigjerrig digital kretselektronikk. Avhandlingen presenterer nye løsninger både innenfor aritmetiske og kombinatoriske kretser, samtidig som den studerer nye statiske minneelementer (SRAM) og alternative minnearkitekturer. Den ser også på utfordringene som oppstår når silisiumteknologien nedskaleres i takt med mikroprosessorutviklingen og foreslår løsninger som bidrar til å gjøre kretsløsninger mer robuste og skalerbare i forhold til denne utviklingen. De viktigste konklusjonene av arbeidet er at man ved å introdusere nye konstruksjonsteknikker både er i stand til å redusere energiforbruket samtidig som robusthet og teknologiskalerbarhet øker. Forskningen har vært utført i samarbeid med Purdue University og vært finansiert av Norges Forskningsråd gjennom FRINATprosjektet ”Micropower Sensor Interface in Nanometer CMOS Technology”

Advanced microarchitecture and circuit design techniques for on-chip memories in CMOS technology

In modern on-chip memories, an increasing demand for higher performance, lower power, reduced area, and improved robustness creates a rising need for advanced microarchitecture and circuit design techniques. Particularly in large-signal multi-ported register files, these advanced design techniques include: (i) multi-banked arrays, (ii) multi-frequency arrays, (iii) multi-bit width gating, (iv) multi-latency cycle times, (v) multi-threshold devices, and (vi) multi-strength keepers. In modern microprocessors, register files are important ingredients, but the increasing number of register file read/write ports and entries can produce a bottleneck. This thesis discusses various new techniques, to address the challenges facing register file designers, and to satisfy microprocessor requirements. The scalability of register files is a concern in modern microprocessors. As microprocessors become wider to exploit instruction level parallelism, this increases the amount of read/write ports. In turn this results in quadratic growth in register file area, decreasing frequency and increasing the power consumption. Multi-banked and multi-frequency register files reduce area and power consumption by relieving the read/write port congestion. Multi-bit width register files reduce active power during read/write operations by gating the clock/wordline. Pipelined register files improve frequency by reducing logic depth, but require multiple cycles for read/write operations. Multi-latency register files contain variable access cycle times, which are dependent on the physical locality of the data. This improves overall microprocessor performance and recovers lost instructions per cycle. As instruction window size continues to expand in modern microprocessors, the resulting demand for additional register file entries requires increased use of wide-OR dynamic circuits. However, these circuits, primarily found in local/global bitlines, are susceptible to leakage noise. In a multi-threshold process, a self-reverse bias technique exploits the use of leaky low-VTH devices, reducing bitline leakage and improving robustness. This circuit topology improves bitline delay from reduced keeper contention. Downsized keepers improve bitline delay in low leakage conditions; stronger keepers improve bitline robustness in high leakage conditions. Utilizing this concept, register files with multi-strength keepers enable robust operation across a wide range of process, voltage, and temperature. These various design techniques show excellent promise in improving performance, power, area, and robustness of multi-ported register files in modern microprocessors

In-situ and In-field temperature and transistor BTI sensing techniques with microprocessor level implementation

In modern deep-scaled CMOS technologies, various silicon-related pitfalls present challenges to the long-term performance of microprocessors. Such challenges include (1) local hot spots, which breach the thermal limitations of a microprocessor, and (2) transistor aging, especially NBTI, which degrades transistor threshold voltage, ultimately threatening the reliability of the entire memory block. In previous systems, the dummy circuit was placed next to the subject, where the dummy was frequently analyzed, and the readout was used to infer the condition of the target. Due to rapidly changing ambient conditions (e.g., temperature and voltage) and the potential scale of the target dimensions, such metrics may not accurately represent the condition of the target. Moreover, such temperature sensors and canary circuits occupy a significant area. Therefore, it would be highly preferable to monitor the target circuit in-situ, i.e., to sense the precise transistor at operation. It is also important to achieve an accurate sensing metric. When the temperature is analyzed, the readout should account for voltage and process variations. While sensing the aging degradation, the readout should account for voltage and temperature fluctuations. This would allow testing during in-field operation, while the circuits achieve area-efficiency. This research had two stages. One result of the first stage was a silicon test chip that was a compact temperature sensor. It involved a family of PTAT+CTAT sensor front-ends that unitized only 6 to 8 conventional CMOS logic devices, yielding a smaller sized chip. The sensor demonstrates accuracy within the target and achieves a 14.3x smaller foot print than preceding published designs. The second product of the first stage was a PMOS aging sensor used in 6T SRAM circuits. The test chip has a real SRAM array, integrated with the proposed PMOS NBTI sensor. It can sense real PMOS NBTI effects in any bit cell (in-situ) and provide robust readings of temperature and voltage (in-field). Intensive aging tests validated the proposed sensing technique. The second stage was focused on implementing the in-situ and in-field sensing techniques in a real processor. The MIPS microprocessor had a modified instruction cache (I$) and instruction set architecture. With the addition of new instruction aging sensing and minor modification of the circuits, the processor can execute aging sensing opportunistically to evaluate the aging level of its instruction cache. A software framework was developed and verified to estimate the retention voltage of the instruction cache over the lifetime of the chip. An area-efficient SoC was developed that could transform the instruction cache into an ambient temperature sensor. It had a physically unclonable function (PUF), and it was built with an area-saving technique similar to the earlier work. This thesis has four chapters. They are presented in chronological and they are aligned with the research described above

Design of Logic-Compatible Embedded Flash Memories for Moderate Density On-Chip Non-Volatile Memory Applications

University of Minnesota Ph.D. dissertation. December 2013. Major: Electrical Engineering. Advisor: Chris H. Kim. 1 computer file (PDF); xx, 129 pages.An on-chip embedded NVM (eNVM) enables a zero-standby power system-on-a-chip with a smaller form factor, faster access speed, lower access power, and higher security than an off-chip NVM. Differently from the high density eNVM technologies such as dual-poly eflash, FeRAM, STT-MRAM, and RRAM that typically require process overhead beyond standard logic process, the moderate density eNVM technologies such as e-fuse, anti-fuse, and single-poly embedded flash (eflash) can be fabricated in a standard logic process with no process overhead. Among them, a single-poly eflash is a unique multiple-time programmable moderate density eNVM, while it is expected to play a key role in mitigating variability and reliability issues of the future VLSI technologies; however, the challenges such as a high voltage disturbance, an implementation of logic compatible High Voltage Switch (HVS), and a limited sensing margin are required to be solved for its implementation using a standard I/O device. This thesis focuses on alleviating such challenges of the single-poly eflash memory with three single-poly eflash designs proposed in a generic logic process for moderate density eNVM applications. Firstly, the proposed 5T eflash features a WL-by-WL accessible architecture with no disturbance issue of the unselected WL cells, an overstress-free multi-story HVS expanding the cell sensing margin, and a selective WL refresh scheme for the higher cell endurance. The most favorable eflash cell configuration is also studied when the performance, endurance, retention, and disturbance characteristics are all considered. Secondly, the proposed 6T eflash features the bit-by-bit re-write capability for the higher overall cell endurance, while not disturbing the unselected WL cells. The logic compatible on-chip charge pump to provide the appropriate high voltages for the proposed eflash operations is also discussed. Finally, the proposed 10T eflash features a multi-configurable HVS that does not require the boosted read supplies, and a differential cell architecture with improved retention time. All these proposed eflash memories were implemented in a 65nm standard logic process, and the test chip measurement results confirmed the functionality of the proposed designs with a reasonable retention margin, showing the competitiveness of the proposed eflash memories compared to the other moderate density eNVM candidates

Architecture and Circuit Design Optimization for Compute-In-Memory

The objective of the proposed research is to optimize computing-in-memory (CIM) design for accelerating Deep Neural Network (DNN) algorithms. As compute peripheries such as analog-to-digital converter (ADC) introduce significant overhead in CIM inference design, the research first focuses on the circuit optimization for inference acceleration and proposes a resistive random access memory (RRAM) based ADC-free in-memory compute scheme. We comprehensively explore the trade-offs involving different types of ADCs and investigate a new ADC design especially suited for the CIM, which performs the analog shift-add for multiple weight significance bits, improving the throughput and energy efficiency under similar area constraints. Furthermore, we prototype an ADC-free CIM inference chip design with a fully-analog data processing manner between sub-arrays, which can significantly improve the hardware performance over the conventional CIM designs and achieve near-software classification accuracy on ImageNet and CIFAR-10/-100 dataset. Secondly, the research focuses on hardware support for CIM on-chip training. To maximize hardware reuse of CIM weight stationary dataflow, we propose the CIM training architectures with the transpose weight mapping strategy. The cell design and periphery circuitry are modified to efficiently support bi-directional compute. A novel solution of signed number multiplication is also proposed to handle the negative input in backpropagation. Finally, we propose an SRAM-based CIM training architecture and comprehensively explore the system-level hardware performance for DNN on-chip training based on silicon measurement results.Ph.D

Gestión de jerarquías de memoria híbridas a nivel de sistema

Tesis inédita de la Universidad Complutense de Madrid, Facultad de Informática, Departamento de Arquitectura de Computadoras y Automática y de Ku Leuven, Arenberg Doctoral School, Faculty of Engineering Science, leída el 11/05/2017.In electronics and computer science, the term ‘memory’ generally refers to devices that are used to store information that we use in various appliances ranging from our PCs to all hand-held devices, smart appliances etc. Primary/main memory is used for storage systems that function at a high speed (i.e. RAM). The primary memory is often associated with addressable semiconductor memory, i.e. integrated circuits consisting of silicon-based transistors, used for example as primary memory but also other purposes in computers and other digital electronic devices. The secondary/auxiliary memory, in comparison provides program and data storage that is slower to access but offers larger capacity. Examples include external hard drives, portable flash drives, CDs, and DVDs. These devices and media must be either plugged in or inserted into a computer in order to be accessed by the system. Since secondary storage technology is not always connected to the computer, it is commonly used for backing up data. The term storage is often used to describe secondary memory. Secondary memory stores a large amount of data at lesser cost per byte than primary memory; this makes secondary storage about two orders of magnitude less expensive than primary storage. There are two main types of semiconductor memory: volatile and nonvolatile. Examples of non-volatile memory are ‘Flash’ memory (sometimes used as secondary, sometimes primary computer memory) and ROM/PROM/EPROM/EEPROM memory (used for firmware such as boot programs). Examples of volatile memory are primary memory (typically dynamic RAM, DRAM), and fast CPU cache memory (typically static RAM, SRAM, which is fast but energy-consuming and offer lower memory capacity per are a unit than DRAM). Non-volatile memory technologies in Si-based electronics date back to the 1990s. Flash memory is widely used in consumer electronic products such as cellphones and music players and NAND Flash-based solid-state disks (SSDs) are increasingly displacing hard disk drives as the primary storage device in laptops, desktops, and even data centers. The integration limit of Flash memories is approaching, and many new types of memory to replace conventional Flash memories have been proposed. The rapid increase of leakage currents in Silicon CMOS transistors with scaling poses a big challenge for the integration of SRAM memories. There is also the case of susceptibility to read/write failure with low power schemes. As a result of this, over the past decade, there has been an extensive pooling of time, resources and effort towards developing emerging memory technologies like Resistive RAM (ReRAM/RRAM), STT-MRAM, Domain Wall Memory and Phase Change Memory(PRAM). Emerging non-volatile memory technologies promise new memories to store more data at less cost than the expensive-to build silicon chips used by popular consumer gadgets including digital cameras, cell phones and portable music players. These new memory technologies combine the speed of static random-access memory (SRAM), the density of dynamic random-access memory (DRAM), and the non-volatility of Flash memory and so become very attractive as another possibility for future memory hierarchies. The research and information on these Non-Volatile Memory (NVM) technologies has matured over the last decade. These NVMs are now being explored thoroughly nowadays as viable replacements for conventional SRAM based memories even for the higher levels of the memory hierarchy. Many other new classes of emerging memory technologies such as transparent and plastic, three-dimensional(3-D), and quantum dot memory technologies have also gained tremendous popularity in recent years...En el campo de la informática, el término ‘memoria’ se refiere generalmente a dispositivos que son usados para almacenar información que posteriormente será usada en diversos dispositivos, desde computadoras personales (PC), móviles, dispositivos inteligentes, etc. La memoria principal del sistema se utiliza para almacenar los datos e instrucciones de los procesos que se encuentre en ejecución, por lo que se requiere que funcionen a alta velocidad (por ejemplo, DRAM). La memoria principal está implementada habitualmente mediante memorias semiconductoras direccionables, siendo DRAM y SRAM los principales exponentes. Por otro lado, la memoria auxiliar o secundaria proporciona almacenaje(para ficheros, por ejemplo); es más lenta pero ofrece una mayor capacidad. Ejemplos típicos de memoria secundaria son discos duros, memorias flash portables, CDs y DVDs. Debido a que estos dispositivos no necesitan estar conectados a la computadora de forma permanente, son muy utilizados para almacenar copias de seguridad. La memoria secundaria almacena una gran cantidad de datos aun coste menor por bit que la memoria principal, siendo habitualmente dos órdenes de magnitud más barata que la memoria primaria. Existen dos tipos de memorias de tipo semiconductor: volátiles y no volátiles. Ejemplos de memorias no volátiles son las memorias Flash (algunas veces usadas como memoria secundaria y otras veces como memoria principal) y memorias ROM/PROM/EPROM/EEPROM (usadas para firmware como programas de arranque). Ejemplos de memoria volátil son las memorias DRAM (RAM dinámica), actualmente la opción predominante a la hora de implementar la memoria principal, y las memorias SRAM (RAM estática) más rápida y costosa, utilizada para los diferentes niveles de cache. Las tecnologías de memorias no volátiles basadas en electrónica de silicio se remontan a la década de1990. Una variante de memoria de almacenaje por carga denominada como memoria Flash es mundialmente usada en productos electrónicos de consumo como telefonía móvil y reproductores de música mientras NAND Flash solid state disks(SSDs) están progresivamente desplazando a los dispositivos de disco duro como principal unidad de almacenamiento en computadoras portátiles, de escritorio e incluso en centros de datos. En la actualidad, hay varios factores que amenazan la actual predominancia de memorias semiconductoras basadas en cargas (capacitivas). Por un lado, se está alcanzando el límite de integración de las memorias Flash, lo que compromete su escalado en el medio plazo. Por otra parte, el fuerte incremento de las corrientes de fuga de los transistores de silicio CMOS actuales, supone un enorme desafío para la integración de memorias SRAM. Asimismo, estas memorias son cada vez más susceptibles a fallos de lectura/escritura en diseños de bajo consumo. Como resultado de estos problemas, que se agravan con cada nueva generación tecnológica, en los últimos años se han intensificado los esfuerzos para desarrollar nuevas tecnologías que reemplacen o al menos complementen a las actuales. Los transistores de efecto campo eléctrico ferroso (FeFET en sus siglas en inglés) se consideran una de las alternativas más prometedores para sustituir tanto a Flash (por su mayor densidad) como a DRAM (por su mayor velocidad), pero aún está en una fase muy inicial de su desarrollo. Hay otras tecnologías algo más maduras, en el ámbito de las memorias RAM resistivas, entre las que cabe destacar ReRAM (o RRAM), STT-RAM, Domain Wall Memory y Phase Change Memory (PRAM)...Depto. de Arquitectura de Computadores y AutomáticaFac. de InformáticaTRUEunpu