DESIGN OF LOW NOISE AMPLIFIER (LNA) IN CMOS PROCESS TECHNOLOGY

This report describes the design and simulation of low noise amplifier (LNA) using AMI06 CMOS process technology. LNA is an amplifier used in communication systems to amplify a very weak input signal while reducing the amount of noise. The core method in designing LNA is to choose the most suitable topology and operating frequency that fit the design requirements. The design proceeds with the calculation of the LNA parameters which are source inductor drain inductor, gate inductor, width of the transistors, bias resistors and block capacitors. Global Positioning System (GPS) and Ultra Wideband (UWB) LNAs have been successfully designed and simulated using Cadence Spectra RFIC Design Software. Simulation results showed that the GPS LNA can amplify weak input signal at frequency range from 1.0 to 1.8 GHz. The LNA obtained gain from 21.348 dB to 25.513 dB. This LNA has achieved noise figure less than 2.518 dB and the power consumption is 16.5mW. For the UWB LNA the frequency range is from 3.1 to 5 GHz which covers the lower band of Ultra Wideband (UWB) technology. The UWB LNA achieved gain from 21.348 dB to 25.513 dB with noise figure less than 3.280 dB

A New Application of Current Conveyors: The Design of Wideband Controllable Low-Noise Amplifiers

The aim of this paper is three-fold. First, it reviews the low-noise amplifier and its relevance in wireless communications receivers. Then it presents an exhaustive review of the existing topologies. Finally, it introduces a new class of LNAs, based on current conveyors, describing the founding principle and the performances of a new single-ended LNA. The new LNAs offer the following notable advantages: total absence of passive elements (and the smallest LNAs in their respective classes); wideband performance, with stable frequency responses from 0 to 3 GHz; easy gain control over wide ranges (0 to 20 dB). Comparisons with other topologies prove that the new class of LNA greatly advances the state of the art

Radio frequency front-end circuits for W-CDMA direct conversion receiver

Master'sMASTER OF ENGINEERIN

High performance building blocks for wireless receiver: multi-stage amplifiers and low noise amplifiers

Different wireless communication systems utilizing different standards and for multiple applications have penetrated the normal people's life, such as Cell phone, Wireless LAN, Bluetooth, Ultra wideband (UWB) and WiMAX systems. The wireless receiver normally serves as the primary part of the system, which heavily influences the system performance. This research concentrates on the designs of several important blocks of the receiver; multi-stage amplifier and low noise amplifier. Two novel multi-stage amplifier typologies are proposed to improve the bandwidth and reduce the silicon area for the application where a large capacitive load exists. They were designed using AMI 0.5 m µ CMOS technology. The simulation and measurement results show they have the best Figure-of-Merits (FOMs) in terms of small signal and large signal performances, with 4.6MHz and 9MHz bandwidth while consuming 0.38mW and 0.4mW power from a 2V power supply. Two Low Noise Amplifiers (LNAs) are proposed, with one designed for narrowband application and the other for UWB application. A noise reduction technique is proposed for the differential cascode Common Source LNA (CS-LNA), which reduces the LNA Noise Figure (NF), increases the LNA gain, and improves the LNA linearity. At the same time, a novel Common Gate LNA (CG-LNA) is proposed for UWB application, which has better linearity, lower power consumption, and reasonable noise performance. Finally a novel practical current injection built-in-test (BIT) technique is proposed for the RF Front-end circuits. If the off-chip component Lg and Rs values are well controlled, the proposed technique can estimate the voltage gain of the LNA with less than 1dB (8%) error

High Performance RF and Basdband Analog-to-Digital Interface for Multi-standard/Wideband Applications

The prevalence of wireless standards and the introduction of dynamic standards/applications, such as software-defined radio, necessitate the next generation wireless devices that integrate multiple standards in a single chip-set to support a variety of services. To reduce the cost and area of such multi-standard handheld devices, reconfigurability is desirable, and the hardware should be shared/reused as much as possible. This research proposes several novel circuit topologies that can meet various specifications with minimum cost, which are suited for multi-standard applications. This doctoral study has two separate contributions: 1. The low noise amplifier (LNA) for the RF front-end; and 2. The analog-to-digital converter (ADC). The first part of this dissertation focuses on LNA noise reduction and linearization techniques where two novel LNAs are designed, taped out, and measured. The first LNA, implemented in TSMC (Taiwan Semiconductor Manufacturing Company) 0.35Cm CMOS (Complementary metal-oxide-semiconductor) process, strategically combined an inductor connected at the gate of the cascode transistor and the capacitive cross-coupling to reduce the noise and nonlinearity contributions of the cascode transistors. The proposed technique reduces LNA NF by 0.35 dB at 2.2 GHz and increases its IIP3 and voltage gain by 2.35 dBm and 2dB respectively, without a compromise on power consumption. The second LNA, implemented in UMC (United Microelectronics Corporation) 0.13Cm CMOS process, features a practical linearization technique for high-frequency wideband applications using an active nonlinear resistor, which obtains a robust linearity improvement over process and temperature variations. The proposed linearization method is experimentally demonstrated to improve the IIP3 by 3.5 to 9 dB over a 2.5–10 GHz frequency range. A comparison of measurement results with the prior published state-of-art Ultra-Wideband (UWB) LNAs shows that the proposed linearized UWB LNA achieves excellent linearity with much less power than previously published works. The second part of this dissertation developed a reconfigurable ADC for multistandard receiver and video processors. Typical ADCs are power optimized for only one operating speed, while a reconfigurable ADC can scale its power at different speeds, enabling minimal power consumption over a broad range of sampling rates. A novel ADC architecture is proposed for programming the sampling rate with constant biasing current and single clock. The ADC was designed and fabricated using UMC 90nm CMOS process and featured good power scalability and simplified system design. The programmable speed range covers all the video formats and most of the wireless communication standards, while achieving comparable Figure-of-Merit with customized ADCs at each performance node. Since bias current is kept constant, the reconfigurable ADC is more robust and reliable than the previous published works

System-level design and RF front-end implementation for a 3-10ghz multiband-ofdm ultrawideband receiver and built-in testing techniques for analog and rf integrated circuits

This work consists of two main parts: a) Design of a 3-10GHz UltraWideBand (UWB) Receiver and b) Built-In Testing Techniques (BIT) for Analog and RF circuits. The MultiBand OFDM (MB-OFDM) proposal for UWB communications has received significant attention for the implementation of very high data rate (up to 480Mb/s) wireless devices. A wideband LNA with a tunable notch filter, a downconversion quadrature mixer, and the overall radio system-level design are proposed for an 11-band 3.4-10.3GHz direct conversion receiver for MB-OFDM UWB implemented in a 0.25mm BiCMOS process. The packaged IC includes an RF front-end with interference rejection at 5.25GHz, a frequency synthesizer generating 11 carrier tones in quadrature with fast hopping, and a linear phase baseband section with 42dB of gain programmability. The receiver IC mounted on a FR-4 substrate provides a maximum gain of 67-78dB and NF of 5-10dB across all bands while consuming 114mA from a 2.5V supply. Two BIT techniques for analog and RF circuits are developed. The goal is to reduce the test cost by reducing the use of analog instrumentation. An integrated frequency response characterization system with a digital interface is proposed to test the magnitude and phase responses at different nodes of an analog circuit. A complete prototype in CMOS 0.35mm technology employs only 0.3mm2 of area. Its operation is demonstrated by performing frequency response measurements in a range of 1 to 130MHz on 2 analog filters integrated on the same chip. A very compact CMOS RF RMS Detector and a methodology for its use in the built-in measurement of the gain and 1dB compression point of RF circuits are proposed to address the problem of on-chip testing at RF frequencies. The proposed device generates a DC voltage proportional to the RMS voltage amplitude of an RF signal. A design in CMOS 0.35mm technology presents and input capacitance <15fF and occupies and area of 0.03mm2. The application of these two techniques in combination with a loop-back test architecture significantly enhances the testability of a wireless transceiver system

Realization of a voltage controlled oscillator using 0.35 um sige-bicmos technology for multi-band applications

The stable growth in wireless communications market has engendered the interoperability of various standards in a single broadband frequency range from hundred MHz up to several GHz. This frequency range consists of various wireless applications such as GSM, Bluetooth and WLAN. Therefore, an agile wireless system needs smart RF front-ends for functioning properly in such a crowded spectrum. As a result, the demand for multi-standard RF transceivers which put various wireless and cordless phone standards together in one structure was increased. The demand for multi-standard RF transceivers gives a key role to reconfigurable wideband VCO operation with low-power and low-phase noise characteristics. Besides agility and intelligence, such a communication system (GSM, WLAN, Global Positioning Systems, etc. ) required meeting the requirements of several standards in a cost-effective way. This, when cost and integration are the major concerns, leads to the exploitation of Si-based technologies. In this thesis, an integrated 2.2-5.7GHz Multi-band differential LC VCO for Multi-standard Wireless Communication systems was designed utilizing 0.35μm SiGe BiCMOS technology. The topology, which combines the switching inductors and capacitors together in the same circuit, is a novel approach for wideband VCOs. Based on the post layout simulation results, the VCO can be tuned using a DC voltage of 0 to 3.3V for 5 different frequency bands (2.27-2.51 GHz, 2.48-2.78GHz, 3.22-3.53GHz, 3.48-3.91GHz and 4.528-5.7GHz) with a maximum bandwidth of 1.36GHz and a minimum bandwidth of 300MHz. The designed and simulated VCO can generate a differential output power between 0.992 dBm and -6.087 dBm with an average power consumption of 44.21mW including the buffers. The average second and third harmonics level were obtained as -37.21 dBm and -47.6 dBm, respectively. The phase noise between -110.45 and -122.5 dBc/Hz, that was simulated at 1 MHz offset, can be obtained through the frequency of interest. Additionally, the figure of merit (FOM), that includes all important parameters such as the phase noise, the power consumption and the ratio of the operating frequency to the offset frequency, is between -176.48 and -181.16 and comparable or better than the ones with the other current VCOs. The main advantage of this study in comparison with the other VCOs, is covering 5 frequency bands starting from 2.27 up to 5.76 GHz without FOM and area abandonment

Dual-band FSK receiver and building block design for UWB impulse radio

Master'sMASTER OF ENGINEERIN

Linearity and Noise Improvement Techniques Employing Low Power in Analog and RF Circuits and Systems

The implementation of highly integrated multi-bands and multi-standards reconfigurable radio transceivers is one of the great challenges in the area of integrated circuit technology today. In addition the rapid market growth and high quality demands that require cheaper and smaller solutions, the technical requirements for the transceiver function of a typical wireless device are considerably multi-dimensional. The major key performance metrics facing RFIC designers are power dissipation, speed, noise, linearity, gain, and efficiency. Beside the difficulty of the circuit design due to the trade-offs and correlations that exist between these parameters, the situation becomes more and more challenging when dealing with multi-standard radio systems on a single chip and applications with different requirements on the radio software and hardware aiming at highly flexible dynamic spectrum access. In this dissertation, different solutions are proposed to improve the linearity, reduce the noise and power consumption in analog and RF circuits and systems. A system level design digital approach is proposed to compensate the harmonic distortion components produced by transmitter circuits’ nonlinearities. The approach relies on polyphase multipath scheme uses digital baseband phase rotation pre-distortion aiming at increasing harmonic cancellation and power consumption reduction over other reported techniques. New low power design techniques to enhance the noise and linearity of the receiver front-end LNA are also presented. The two proposed LNAs are fully differential and have a common-gate capacitive cross-coupled topology. The proposed LNAs avoids the use of bulky inductors that leads to area and cost saving. Prototypes are implemented in IBM 90 nm CMOS technology for the two LNAs. The first LNA covers the frequency range of 100 MHz to 1.77 GHz consuming 2.8 mW from a 2 V supply. Measurements show a gain of 23 dB with a 3-dB bandwidth of 1.76 GHz. The minimum NF is 1.85 dB while the input return loss is greater than 10 dB across the entire band. The second LNA covers the frequency range of 100 MHz to 1.6 GHz. A 6 dBm third-order input intercept point, IIP3, is measured at the maximum gain frequency. The core consumes low power of 1.55 mW using a 1.8 V supply. The measured voltage gain is 15.5 dB with a 3-dB bandwidth of 1.6 GHz. The LNA has a minimum NF of 3 dB across the whole band while achieving an input return loss greater than 12 dB. Finally, A CMOS single supply operational transconductance amplifier (OTA) is reported. It has high power supply rejection capabilities over the entire gain bandwidth (GBW). The OTA is fabricated on the AMI 0.5 um CMOS process. Measurements show power supply rejection ratio (PSRR) of 120 dB till 10 KHz. At 10 MHz, PSRR is 40 dB. The high performance PSRR is achieved using a high impedance current source and two noise reduction techniques. The OTA offers a very low current consumption of 25 uA from a 3.3 V supply