Classification and localization of electromagnetic and ultrasonic pulsed emitters

Mención Internacional en el título de doctorThe localization of radiative sources is very important in many fields of work such as: sonar, radar and underwater radar, indoor localization in wireless networks, earthquake epicenter localization, defective assets localization in electrical facilities and so forth. In the process of locating radiative sources exist many issues which can provoke errors in the localization. The signals acquired may belong to different sources or they can be mixed with environmental noise, then, their separation before using localization algorithms is of great interest to be efficient and accurate in the computational process. Furthermore, the geometry and radiation characteristics of the receivers, the nature of the signal or their measuring process may cause deviations in the signal onset calculus and therefore the source localization could be displaced from the actual position. In this thesis, there are three kinds of algorithms to undertake three steps in the emitter localization: signal separation, onset and time delay estimation of the signals and source localization. For each step, in order to reduce the error in the localization, several algorithms are analyzed and compared in each application, to choose the most reliable. As the first step, to separate different kinds of signals is of interest to facilitate further processing. In this thesis, different optimization techniques are presented over the power ratio (PR) maps method. The PR uses a selective spectral signal characterization to extract the features of the analyzed signals. The technique identifies automatically the most representative frequency bands which report a great separation of the different kinds of signals in the PR map. After separating and selecting the signals, it is of interest to compare the algorithms to calculate the onset and time delay of the pulsed signals to know their performance because the time variables are inputs to the most common triangulation algorithms to locate radiative and ultrasonic sources. An overview of the algorithms used to estimate the time of flight (ToF) and time differences of arrival (TDoA) of pulsed signals is done in this thesis. In the comparison, there is also a new algorithm based on statics of high order, which is proposed in this thesis. The survey of their performance is done applied to muscle deep estimation, localization in one dimension (1D), and for the localization of emitters in three dimensions (3D). The results show how the presented algorithm yields great results. As the last step in the radiative source localization, the formulation and principle of work of both iterative and non-iterative triangulation algorithms are presented. A new algorithm is presented as a combination of two already existing improving their performance when working alone. All the algorithms, the proposed and the previous which already exist, are compared in terms of accuracy and computational time. The proposed algorithm reports good results in terms of accuracy and it is one of the fastest in computational time. Once the localization is achieved, it is of great interest to understand how the errors in the determination of the onset of the signals are propagated in the emitter localization. The triangulation algorithms estimate the radiative source position using time variables as inputs: ToF, TDoA or pseudo time of flight (pToF) and the receiver positions. The propagation of the errors in the time variables to the radiative source localization is done in two dimensions (2D) and 3D. New spherical diagrams have been created to represent the directions where the localization is more or less sensible to the errors. This study and their sphere diagrams are presented for several antenna layouts. Finally, how the errors in the positioning of the receivers are propagated to the emitter localization is analyzed. In this study, the effect in the propagation of both the relative distance from the receivers to the emitter and the direction between them has been characterized. The propagation of the error considering the direction is also represented in spherical diagrams. For a preferred direction identified in the spheres, the propagated error in the source localization has been quantified regarding both the source distance and the magnitude of the errors in the receivers positioning.Programa Oficial de Doctorado en Ingeniería Eléctrica, Electrónica y AutomáticaPresidente: Andrea Cavallini.- Secretario: José Antonio García Souto.- Vocal: Iliana Portugués Peter

Deep Learning Methods for Remote Sensing

Remote sensing is a field where important physical characteristics of an area are exacted using emitted radiation generally captured by satellite cameras, sensors onboard aerial vehicles, etc. Captured data help researchers develop solutions to sense and detect various characteristics such as forest fires, flooding, changes in urban areas, crop diseases, soil moisture, etc. The recent impressive progress in artificial intelligence (AI) and deep learning has sparked innovations in technologies, algorithms, and approaches and led to results that were unachievable until recently in multiple areas, among them remote sensing. This book consists of sixteen peer-reviewed papers covering new advances in the use of AI for remote sensing

Swarm Robotics

Collectively working robot teams can solve a problem more efficiently than a single robot, while also providing robustness and flexibility to the group. Swarm robotics model is a key component of a cooperative algorithm that controls the behaviors and interactions of all individuals. The robots in the swarm should have some basic functions, such as sensing, communicating, and monitoring, and satisfy the following properties

Smart Sensor Technologies for IoT

The recent development in wireless networks and devices has led to novel services that will utilize wireless communication on a new level. Much effort and resources have been dedicated to establishing new communication networks that will support machine-to-machine communication and the Internet of Things (IoT). In these systems, various smart and sensory devices are deployed and connected, enabling large amounts of data to be streamed. Smart services represent new trends in mobile services, i.e., a completely new spectrum of context-aware, personalized, and intelligent services and applications. A variety of existing services utilize information about the position of the user or mobile device. The position of mobile devices is often achieved using the Global Navigation Satellite System (GNSS) chips that are integrated into all modern mobile devices (smartphones). However, GNSS is not always a reliable source of position estimates due to multipath propagation and signal blockage. Moreover, integrating GNSS chips into all devices might have a negative impact on the battery life of future IoT applications. Therefore, alternative solutions to position estimation should be investigated and implemented in IoT applications. This Special Issue, “Smart Sensor Technologies for IoT” aims to report on some of the recent research efforts on this increasingly important topic. The twelve accepted papers in this issue cover various aspects of Smart Sensor Technologies for IoT

Random Actuation Pattern Optimization by Genetic Algorithm for Ultrasonic Structural Health Monitoring of Plates

The objective of this research is to investigate an optimized two-dimensional random pattern of uniformly excited points using the Genetic Algorithm (GA) technique for structural health monitoring. The point excitations generate ultrasonic waves in both isotropic and anisotropic materials that can be effective in diagnosing structural defects. The formed ultrasonic waves can constructively interfere and send out an intense wave beam to a predetermined target. The constructed wave beams can be steered to different directions with variable target distances. In the GA, the cost function is constructed to reduce main lobe beamwidth, eliminate grating lobes and suppress sidelobes’ levels. Mathematical modelling, finite element simulations, and optimizations are successively performed to achieve the objectives. Secondly Firstly, a mathematical beamforming model is developed to describe the excitation pattern of which each point is excited at the same time delay with a uniform weighting factor. The derived methodology accounts for enclosing all excitations within a certain aperture. The centroid of the emitting sources is also kept at the origin of the Cartesian coordinate within a slight tolerance range. For the near field, in isotropic materials, the excitation points lay on equally spaced circular arcs centered at the target point. In anisotropic materials, such as composites, the wave amplitude and phase velocity are highly dependent on fiber directions. Because of anisotropic nature, the excitation geometry becomes quite complicated. Secondly, finite element models for aluminum and composite plates are simulated to extract wave characteristics, such as displacement amplitudes, phase velocity profiles and slowness curves. These data are implemented later in the optimization algorithm. A quarter plate of radius 150mm and 1.125mm thickness is modelled as a three-dimensional solid part. A concentrated force with a 2.5 cycle-Hanning window sinusoidal signal is applied at the center of the plate and the boundaries are chosen to be symmetrical. Radial sensors at 5 degrees increments are positioned at 50mm from the excitation source to measure wave properties. The simulation results show that the amplitude and velocity are uniform for isotropic materials whereas the waves propagate rapidly with higher amplitudes along the fibers in anisotropic materials. Thirdly, after collecting all the required information, a GA optimization technique is applied to generate the excitation population of x- and y-coordinates. The pre-determined population is permutated, cross-overed and mutated so that additional possibilities are produced. The same process is repeated for many generations until the local optimum result is obtained. Finally, the near field beamforming is plotted in MATLAB at different actuation point numbers for the isotropic and anisotropic materials. The results are then compared to other linear, circular and planar patterns found in literature

Advanced Sensors for Real-Time Monitoring Applications

It is impossible to imagine the modern world without sensors, or without real-time information about almost everything—from local temperature to material composition and health parameters. We sense, measure, and process data and act accordingly all the time. In fact, real-time monitoring and information is key to a successful business, an assistant in life-saving decisions that healthcare professionals make, and a tool in research that could revolutionize the future. To ensure that sensors address the rapidly developing needs of various areas of our lives and activities, scientists, researchers, manufacturers, and end-users have established an efficient dialogue so that the newest technological achievements in all aspects of real-time sensing can be implemented for the benefit of the wider community. This book documents some of the results of such a dialogue and reports on advances in sensors and sensor systems for existing and emerging real-time monitoring applications

Development of an active vision system for robot inspection of complex objects

Dissertação de mestrado integrado em Engenharia Mecânica (área de especialização em Sistemas Mecatrónicos)The dissertation presented here is in the scope of the IntVis4Insp project between University of Minho and the company Neadvance. It focuses on the development of a 3D hand tracking system that must be capable of extracting the hand position and orientation to prepare a manipulator for automatic inspection of leather pieces. This work starts with a literature review about the two main methods for collecting the necessary data to perform 3D hand tracking. These divide into glove-based methods and vision-based methods. The first ones work with some kind of support mounted on the hand that holds all the necessary sensors to measure the desired parameters. While the second ones recur to one or more cameras to capture the hands and through computer vision algorithms track their position and configuration. The selected method for this work was the vision-based method Openpose. For each recorded image, this application can locate 21 hand keypoints on each hand that together form a skeleton of the hands. This application is used in the tracking system developed throughout this dissertation. Its information is used in a more complete pipeline where the location of those hand keypoints is crucial to track the hands in videos of the demonstrated movements. These videos were recorded with an RGB-D camera, the Microsoft Kinect, which provides a depth value for every RGB pixel recorded. With the depth information and the 2D location of the hand keypoints in the images, it was possible to obtain the 3D world coordinates of these points considering the pinhole camera model. To define the hand, position a point is selected among the 21 for each hand, but for the hand orientation, it was necessary to develop an auxiliary method called “Iterative Pose Estimation Method” (ITP), which estimates the complete 3D pose of the hands. This method recurs only to the 2D locations of every hand keypoint, and the complete 3D world coordinates of the wrists to estimate the right 3D world coordinates of all the remaining points on the hand. This solution solves the problems related to hand occlusions that a prone to happen due to the use of only one camera to record the inspection videos. Once the world location of all the points in the hands is accurately estimated, their orientation can be defined by selecting three points forming a plane.A dissertação aqui apresentada insere-se no âmbito do projeto IntVis4Insp entre a Universidade do Minho e a empresa Neadavance, e foca-se no desenvolvimento de um sistema para extração da posição e orientação das mãos no espaço para posterior auxílio na manipulação automática de peças de couro, com recurso a manipuladores robóticos. O trabalho inicia-se com uma revisão literária sobre os dois principais métodos existentes para efetuar a recolha de dados necessária à monitorização da posição e orientação das mãos ao longo do tempo. Estes dividem-se em métodos baseados em luvas ou visão. No caso dos primeiros, estes recorrem normalmente a algum tipo de suporte montado na mão (ex.: luva em tecido), onde estão instalados todos os sensores necessários para a medição dos parâmetros desejados. Relativamente a sistemas de visão estes recorrem a uma câmara ou conjunto delas para capturar as mãos e por via de algoritmos de visão por computador determinam a sua posição e configuração. Foi selecionado para este trabalho um algoritmo de visão por computador denominado por Openpose. Este é capaz de, em cada imagem gravada e para cada mão, localizar 21 pontos pertencentes ao seu esqueleto. Esta aplicação é inserida no sistema de monitorização desenvolvido, sendo utilizada a sua informação numa arquitetura mais completa onde é efetuada a extração da localização dos pontos chave de cada mão nos vídeos de demonstração dos movimentos de inspeção. A gravação destes vídeos é efetuada com uma câmara RGB-D, a Microsoft Kinect, que fornece um valor de profundidade para cada pixel RGB gravado. Com os dados de profundidade e a localização dos pontos chave nas imagens foi possível obter as coordenadas 3D no mundo destes pontos considerando o modelo pinhole para a câmara. No caso da posição da mão é selecionado um ponto de entre os 21 para a definir ao longo do tempo, no entanto, para o cálculo da orientação foi desenvolvido um método auxiliar para estimação da pose tridimensional da mão denominado por “Iterative Pose Estimation Method” (ITP). Este método recorre aos dados 2D do Openpose e às coordenadas 3D do pulso de cada mão para efetuar a correta estimação das coordenadas 3D dos restantes pontos da mão. Isto permite essencialmente resolver problemas com oclusões da mão, muito frequentes com o uso de uma só câmara na gravação dos vídeos. Uma vez estimada corretamente a posição 3D no mundo dos vários pontos da mão, a sua orientação pode ser definida com recurso a quaisquer três pontos que definam um plano

時間と周波数領域情報に基づいたシステムモデリングとその応用

System modeling is required to deal with the time-varying system dynamics or the experimental data with insufficient information. However, the existing methods cannot construct satisfactory models for rapidly varying systems or severely band-limited signals. This thesis focuses on the new approaches to solve such system modeling problems based on time and frequency-domain information and illustrates their applications in time-varying channel identification and localization system. For the rapid time-varying systems, parameters can be approximated by the cosine series using virtual even periodic functions. Following the orthogonality of the trigonometric functions, the parameter estimation is recursively implemented by estimating the coefficients of each degree of the cosine harmonic term. For the localization system with insufficient frequency components, the spectral characteristics including phase information in frequency domain and the information evaluation in time domain are applied to improve the convergence performance. Numerical simulations demonstrate the effectiveness of the new approaches.北九州市立大