A Study on the Hierarchical Control Structure of the Islanded Microgrid

The microgrid is essential in promoting the power system’s resilience through its ability to host small-scale DG units. Furthermore, the microgrid can isolate itself during main grid faults and supply its demands. However, islanded operation of the microgrid is challenging due to difficulties in frequency and voltage control. In islanded mode, grid-forming units collaborate to control the frequency and voltage. A hierarchical control structure employing the droop control technique provides these control objectives in three consecutive levels: primary, secondary, and tertiary. However, challenges associated with DG units in the vicinity of distribution networks limit the effectiveness of the islanded mode of operation.In MV and LV distribution networks, the X/R ratio is low; hence, the frequency and voltage are related to the active and reactive power by line parameters. Therefore, frequency and voltage must be tuned for changes in active or reactive powers. Furthermore, the line parameters mismatch causes the voltage to be measured differently at each bus due to the different voltage drops in the lines. Hence, a trade-off between voltage regulation and reactive power-sharing is formed, which causes either circulating currents for voltage mismatch or overloading for reactive power mismatch. Finally, the economic dispatch is usually implemented in tertiary control, which takes minutes to hours. Therefore, an estimation algorithm is required for load and renewable energy quantities forecasting. Hence, prediction errors may occur that affect the stability and optimality of the control. This dissertation aims to improve the power system resilience by enhancing the operation of the islanded microgrid by addressing the above-mentioned issues. Firstly, a linear relationship described by line parameters is used in droop control at the primary control level to accurately control the frequency and voltage based on measured active and reactive power. Secondly, an optimization-based consensus secondary control is presented to manage the trade-off between voltage regulation and reactive power-sharing in the inductive grid with high line parameters mismatch. Thirdly, the economic dispatch-based secondary controller is implemented in secondary control to avoid prediction errors by depending on the measured active and reactive powers rather than the load and renewable energy generation estimation. The developed methods effectively resolve the frequency and voltage control issues in MATLAB/SIMULINK simulations

Enhanced decoupling current scheme with selective harmonic elimination pulse width modulation for cascaded multilevel inverter based static synchronous compensator

This dissertation is dedicated to a comprehensive study and performance analysis of the transformer-less Multilevel Cascaded H-bridge Inverter (MCHI) based STATic synchronous COMpensator (STATCOM). Among the shunt-connected Flexible AC Transmission System (FACTS) controllers, STATCOM has shown extensive feasibility and effectiveness in solving a wide range of power quality problems. By referring to the literature reviews, MCHI with separated DC capacitors is certainly the most versatile power inverter topology for STATCOM applications. However, due to the ill-defined transfer functions, complex control schemes and formulations were emerged to achieve a low-switching frequency high-bandwidth power control. As a result, adequate controller parameters were generally obtained by using trial and error method, which were practically ineffective and time-consuming. In this dissertation, the STATCOM is controlled to provide reactive power (VAR) compensation at the Point of Common Coupling (PCC) under different loading conditions. The goal of this work is to enhance the performance of the STATCOM with the associated proposed control scheme in achieving high dynamic response, improving transient performance, and producing high-quality output voltage waveform. To evaluate the superiority of the proposed control scheme, intensive simulation studies and numerous experiments are conducted accordingly, where a very good match between the simulation results and the experimental results is achieved in all cases and documented in this dissertation

Optimization Techniques for the Developing Distribution System

The most rapidly changing part of today’s power grid is the distribution system. Many new technologies have emerged that revolutionize the way utilities provide, and now sometimes receive, power to and from their customers. To an extent, the push for de-regulation of utilities has also led to an increased focus on reliability and efficiency. These changes make design and operation of power systems more complex causing utilities to question if they are operating optimally. Operations Research (OR) is an area of mathematics where quantitative analysis is used to provide a basis for complex decision making. The changing landscape in electric distribution makes it a prime candidate for the application of OR techniques. This research seeks to develop optimization methods that can be applied to any distribution feeder or group of feeders that allows for optimal decisions to be made in a reasonable time frame. Two specific applications identified in this thesis are optimal reconfiguration during outage situations and optimal location of Battery Energy Storage Systems (BESS). Response to outages has traditionally relied on human-in-the-loop approaches where a dispatcher or a crew working the field decides what switching operations are needed to isolate affected parts of the system and restore power to healthy ones. This approach is time consuming and under-utilizes the benefits provided by widely-adopted, remotely-controlled switching technologies. Chapters Two and Three of this thesis develop a partitioning method for determining the switching operations required to optimize the amount of load that is restored during an event. Most people would agree that renewable forms of Distributed Generation (DG) provide great benefits to the power industry, especially through reduced impact on the environment. The variable nature of renewables, however, can cause many issues for operation and control of a utilities’ system, especially for distribution interconnections. Storage technologies are thought to be the primary solution to these issues with much research focused on sizing and control of BESSs. Equally important for integration, but often overlooked, is the location at which the device is connected. Chapter Four explores this idea by drawing conclusions about optimal BESS location based on well-studied ideas of optimal capacitor location

Performance Analysis of Photovoltaic Fed Distributed Static Compensator for Power Quality Improvement

Owing to rising demand for electricity, shortage of fossil fuels, reliability issues, high transmission and distribution losses, presently many countries are looking forward to integrate the renewable energy sources into existing electricity grid. This kind of distributed generation provides power at a location close to the residential or commercial consumers with low transmission and distribution costs. Among other micro sources, solar photovoltaic (PV) systems are penetrating rapidly due to its ability to provide necessary dc voltage and decreasing capital cost. On the other hand, the distribution systems are confronting serious power quality issues because of various nonlinear loads and impromptu expansion. The power quality issues incorporate harmonic currents, high reactive power burden, and load unbalance and so on. The custom power device widely used to improve these power quality issues is the distributed static compensator (DSTATCOM). For continuous and effective compensation of power quality issues in a grid connected solar photovoltaic distribution system, the solar inverters are designed to operate as a DSTATCOM thus by increasing the efficiency and reducing the cost of the system. The solar inverters are interfaced with grid through an L-type or LCL-type ac passive filters. Due to the voltage drop across these passive filters a high amount of voltage is maintained across the dc-link of the solar inverter so that the power can flow from PV source to grid and an effective compensation can be achieved. So in the thesis a new topology has been proposed for PV-DSTATCOM to reduce the dc-link voltage which inherently reduces the cost and rating of the solar inverter. The new LCLC-type PV-DSTATCOM is implemented both in simulation and hardware for extensive study. From the obtained results, the LCLC-type PV-DSTATCOM found to be more effective than L-type and LCL-type PV-DSTATCOM. Selection of proper reference compensation current extraction scheme plays the most crucial role in DSTATCOM performance. This thesis describes three time-domain schemes viz. Instantaneous active and reactive power (p-q), modified p-q, and IcosΦ schemes. The objective is to bring down the source current THD below 5%, to satisfy the IEEE-519 Standard recommendations on harmonic limits. Comparative evaluation shows that, IcosΦ scheme is the best PV-DSTATCOM control scheme irrespective of supply and load conditions. In the view of the fact that the filtering parameters of the PV-DSTATCOM and gains of the PI controller are designed using a linearized mathematical model of the system. Such a design may not yield satisfactory results under changing operating conditions due to the complex, nonlinear and time-varying nature of power system networks. To overcome this, evolutionary algorithms have been adopted and an algorithm-specific control parameter independent optimization tool (JAYA) is proposed. The JAYA optimization algorithm overcomes the drawbacks of both grenade explosion method (GEM) and teaching learning based optimization (TLBO), and accelerate the convergence of optimization problem. Extensive simulation studies and real-time investigations are performed for comparative assessment of proposed implementation of GEM, TLBO and JAYA optimization on PV-DSTATCOM. This validates that, the PV-DSTATCOM employing JAYA offers superior harmonic compensation compared to other alternatives, by lowering down the source current THD to drastically small values. Another indispensable aspect of PV-DSTATCOM is that due to parameter variation and nonlinearity present in the system, the reference current generated by the reference compensation current extraction scheme get altered for a changing operating conditions. So a sliding mode controller (SMC) based p-q theory is proposed in the dissertation to reduce these effects. To validate the efficacy of the implemented sliding mode controller for the power quality improvement, the performance of the proposed system with both linear and non-linear controller are observed and compared by taking total harmonic distortion as performance index. From the obtained simulation and experimentation results it is concluded that the SMC based LCLC-type PV-DSTATCOM performs better in all critical operating conditions

Power quality analysis and automatic intelligent control strategy for solar PV microgrid

My thesis focuses on quantification of the power quality issues in a solar photovoltaic based microgrid network through the simulation and experimental approach. PSO based optimization control strategy was also implemented to further improve the power quality factors in the Microgrid network<br /

New Analysis and Operational Control Algorithms for Islanded Microgrid Systems

Driven by technical, economic and environmental benefits for different stakeholders in the power industry, the electric distribution system is currently undergoing a major paradigm shift towards having an increasing portion of its growing demand supplied via distributed generation (DG) units. As the number of DG units increase; microgrids can be defined within the electric distribution system as electric regions with enough generation to meet all or most of its local demand. A microgrid should be able to operate in two modes, grid-connected or islanded. The IEEE standard 1547.4 enumerates a list of potential benefits for the islanded microgrid operation. Such benefits include: 1) improving customers’ reliability, 2) relieving electric power system overload problems, 3) resolving power quality issues, and 4) allowing for maintenance of the different power system components without interrupting customers. These benefits motivate the operation of microgrid systems in the islanded mode. However the microgrid isolation from the main grid creates special technical challenges that have to be comprehensively investigated in order to facilitate a successful implementation of the islanded microgrid concept. Motivated by these facts, the target of this thesis is to introduce new analysis and operational control algorithms to tackle some of the challenges associated with the practical implementation of the islanded microgrid concept. In order to accomplish this target, this study is divided into four perspectives: 1) developing an accurate steady-state analysis algorithm for islanded microgrid systems, 2) maximizing the possible utilization of islanded microgrid limited generation resources, 3) allowing for the decentralized operation of islanded microgrid systems and 4) enabling the islanded microgrid operation in distribution systems with high penetration of plug-in electric vehicles (PEVs). First for the steady-state analysis of islanded microgrid systems, a novel and generalized algorithm is proposed to provide accurate power flow analysis of islanded microgrid systems. Conventional power flow tools found in the literature are generally not suitable for the islanded microgrid operating mode. The reason is that none of these tools reflect the islanded microgrid special philosophy of operation in the absence of the utility bus. The proposed algorithm adopts the real characteristics of the islanded microgrid operation; i.e., 1) Some of the DG units are controlled using droop control methods and their generated active and reactive power are dependent on the power flow variables and cannot be pre-specified; 2) The steady-state system frequency is not constant and is considered as one of the power flow variables. The proposed algorithm is generic, where the features of distribution systems i.e. three-phase feeder models, unbalanced loads and load models have been taken in consideration. The effectiveness of the proposed algorithm, in providing accurate steady-state analysis of islanded microgrid systems, is demonstrated through several case studies. Secondly, this thesis proposes the consideration of a system maximum loadability criterion in the optimal power flow (OPF) problem of islanded microgrid systems. Such consideration allows for an increased utilization of the islanded microgrid limited generation resources when in isolation from the utility grid. Three OPF problem formulations for islanded microgrids are proposed; 1) The OPF problem for maximum loadability assessment, 2) The OPF for maximizing the system loadability, and 3) The bi-objective OPF problem for loadability maximization and generation cost minimization. An algorithm to achieve a best compromise solution between system maximum loadability and minimum generation costs is also proposed. A detailed islanded microgrid model is adopted to reflect the islanded microgrid special features and real operational characteristics in the proposed OPF problem formulations. The importance and consequences of considering the system maximum loadability in the operational planning of islanded microgrid systems are demonstrated through comparative numerical studies. Next, a new probabilistic algorithm for enabling the decentralized operation of islanded microgrids, including renewable resources, in the absence of a microgrid central controller (MGCC) is proposed. The proposed algorithm adopts a constraint hierarchy approach to enhance the operation of islanded microgrids by satisfying the system’s operational constraints and expanding its loading margin. The new algorithm takes into consideration the variety of possible islanded microgrid configurations that can be initiated in a distribution network (multi-microgrids), the uncertainty and variability associated with the output power of renewable DG units as well as the variability of the load, and the special operational philosophy associated with islanded microgrid systems. Simulation studies show that the proposed algorithm can facilitate the successful implementation of the islanded microgrid concept by reducing customer interruptions and enhancing the islanded microgrid loadability margins. Finally, this research proposes a new multi-stage control scheme to enable the islanded microgrid operation in the presence of high PEVs penetration. The proposed control scheme optimally coordinates the DG units operation, the shedding of islanded microgrid power demand (during inadequate generation periods) and the PEVs charging/discharging decisions. To this end, a three-stage control scheme is formulated in order to: 1) minimize the load shedding, 2) satisfy the PEVs customers’ requirements and 3) minimize the microgrid cost of operation. The proposed control scheme takes into consideration; the variability associated with the output power of renewable DG units, the random behaviour of PEV charging and the special features of islanded microgrid systems. The simulation studies show that the proposed control scheme can enhance the operation of islanded microgrid systems in the presence of high PEVs penetration and facilitate a successful implementation of the islanded microgrid concept, under the smart grid paradigm

Steady-State Analysis and Optimal Power Routing of Standalone Unbalanced Hybrid AC/DC Microgrids

The concept of ac microgrids was introduced to integrate distributed generators (DGs) and loads within one entity that can operate autonomously or connected to a utility grid. Furthermore, dc microgrids have received increasing attention as a potential solution to deliver power from DGs to modern dc loads with reduced conversion stages. Moreover, hybrid ac/dc microgrids have been introduced as a paradigm combining the benefits of the two types of microgrids by interconnecting them through interlinking converters (ICs). Steady-state analysis is essential for planning and operation studies of electrical power systems. However, conventional analysis approaches cannot be applied to hybrid ac/dc microgrids due to their distinctive features, such as droop characteristics, lack of a slack bus, and coupling between the ac and dc variables. Additionally, the unbalanced nature of ac microgrids adds to the complexity of modeling and analysis in such networks. Therefore, this thesis is focused on developing steady-state modeling and analysis framework for standalone unbalanced hybrid ac/dc microgrids. First, a steady-state analysis tool for unbalanced hybrid ac/dc microgrids is developed. The ac subgrid's components are modeled in phase coordinates. Furthermore, the dc subgrid's components are modeled and the coupling between the ac and dc variables is formulated. The models of the various system elements are incorporated into a unified power flow formulation, which is solved using a Newton-Trust Region (NTR) method. The developed power flow algorithm is verified through comparisons with time-domain simulations of test microgrids. The analysis tool is used to analyze a larger hybrid ac/dc microgrid through case studies. The case studies shed light on some challenges of these microgrids, namely, imposed limitations on microgrid loadability due to unbalanced ac subgrid's loading, effect of IC settings on microgrid operation, and trade-off between proportional loading of the ac and dc subgrids and proportional power-transfer sharing among ICs. Second, based on the identified microgrid loadability limitation of unbalanced microgrids, a novel adaptive power routing (APR) scheme is proposed to maximize the microgrid loadability. The proposed scheme allows independent control of active and reactive powers flowing through IC phases, so that power can be routed among the ac subgrid's phases. The DPR scheme is integrated into an optimal power flow (OPF) formulation with the objective of minimizing load shedding. A supervisory controller is proposed to solve the OPF problem by adjusting the DG and IC settings. Several case studies are conducted to show the ineffectiveness of conventional supervisory controllers in resolving the loadability issue, and to verify the success of the proposed controller in solving the problem. Third, a power flow approach based on sequence component analysis of the ac microgrid's elements is adopted for faster convergence and improved modeling accuracy as compared to conventional approaches in phase coordinates. This approach breaks down the system model into positive-, negative-, and zero-sequence subsystems that can be solved in parallel for enhanced performance. The positive-sequence power flow is solved using a Newton-Raphson (NR) method, while the negative- and zero-sequence voltages are obtained by solving linear complex equations. The approach is verified through comparisons with time-domain simulations. In addition, the algorithm is utilized to investigate the operation of droop-controlled DGs in larger-scale isochronous unbalanced ac microgrids, and to examine its limit-enforcement abilities at the same time. The algorithm demonstrates significant improvements in terms of accuracy and convergence time when compared against the conventional NTR-based approach in phase coordinates. Finally, the power flow approach developed in the third part is extended to include the IC's and dc subgrid's models so that it can be applied to hybrid ac/dc microgrids. A power flow algorithm is proposed to solve the ac and dc power flows independently in a sequential manner, while maintaining the correlation between the two. The algorithm is verified through comparisons with time-domain models of test hybrid microgrids. Case studies are introduced to test the algorithm's effectiveness in enforcing the DG and IC limits in the power flow solution under various conditions. The algorithm also shows enhanced accuracy and solution speed with respect to the tool developed in the first stage

An Update on Power Quality

Power quality is an important measure of fitness of electricity networks. With increasing renewable energy generations and usage of power electronics converters, it is important to investigate how these developments will have an impact to existing and future electricity networks. This book hence provides readers with an update of power quality issues in all sections of the network, namely, generation, transmission, distribution and end user, and discusses some practical solutions

Intelligent control of PV co-located storage for feeder capacity optimization

Battery energy storage is identified as a strong enabler and a core element of the next generation grid. However, at present the widespread deployment of storage is constrained by the concerns that surround the techno-economic viability. This thesis addresses this issue through optimal integration of storage to improve the efficiency of the electricity grid. A holistic approach to optimal integration includes the development of methodologies for optimal siting, sizing and dispatch coordination of storage