Antenna Reconfiguration Using Electrically Actuated Liquid-Metal Pixels.

M.S. Thesis. University of Hawaiʻi at Mānoa 2017

Stretching the limits of dynamic range, shielding effectiveness, and multiband frequency response

In this dissertation, an RF MEMS variable capacitor suitable for applications requiring ultrawide capacitive tuning ranges is reported. The device uses an electrostatically tunable liquid dielectric interface to continuously vary the capacitance without the use of any moving parts. As compared to existing MEMS varactors in literature, this device has an extremely simple design that can be implemented using simple fabrication methods that do not necessitate the use of clean room equipment. In addition, this varactor is particularly suited for incorporating a wide range of liquid dielectric materials for specific tuning ratio requirements. Additionally, the shielding effectiveness performance of graphene-doped ABS thin films is investigated. The use of graphene as a replacement for metal fillers in composite EMI shielding materials is quickly becoming a widely-investigated field in the electromagnetic compatibility community. By replacing conventional metal-based shielding methods with graphene-doped polymers, low-weight, field-use temporary shielding enclosures can be implemented that do not suffer from mechanical unreliability and corrosion/oxidation like a traditional metal enclosure. While the performance of composite EMI shielding materials has not yet surpassed metals, the advantages of polymer-based shielding methods could find usage in a variety of applications. Finally, mutliband pre-fractal antennas fabricated via 3D printing are reported. These devices are the first to incorporate the advantages of 3D printing (rapid prototyping, fabrication of complex geometries otherwise unobtainable) with the advantages of self-similar antennas (increased gain and multiband performance) in a single device. The Sierpinski tetrahedron-based antenna design was both computationally modeled and physically realized to illustrate its potential as a solution to enable true multiband communication platforms

Reconfigurable Liquid-Metal Circuits and Antennas: Magnetic and Pressure-Based Actuation for Improved Performance at Microwave Frequencies

M.S. Thesis. University of Hawaiʻi at Mānoa 2018

Elastomer-based pneumatic switch for radio frequency microdevices

This paper reports the realization and characterization of a pneumatic microswitch integrated with a high-frequency radio frequency (RF) transmission line on an elastomer substrate. A process for the fabrication of low-loss RF coplanar transmission lines on flexible elastomeric polydimethylsiloxane (PDMS) substrates was developed, and devices realized using this process were used to determine the characteristics of PDMS as an RF substrate with uniform low loss and low dielectric constant being measure

Nematic Liquid Crystal Carbon Nanotube Composite Materials for Designing RF Switching Devices

Radio frequency microelectromechanical systems (RF MEMS) devices are microdevices used to switch or modify signals from the RF to millimeter wave (mmWave) frequency range. Liquid crystals (LCs) are widely used as electro-optic modulators for display devices. An electric field-induced electrical conductivity modulation of pure LC media is quite low which makes it difficult to use for RF MEMS switching applications. Currently, RF MEMS devices are characterized as an excellent option between solid-state and electromechanical RF switches to provide high isolation, low insertion loss, low power usage, excellent return loss, and large frequency band. However, commercial usage is low due to their lower switching speed, reliability, and repeatability. This research presents an electrical conductivity enhancement through the use of carbon nanotube (CNT) doping of LCs to realize a high-performance RF LC-CNT switching device. This thesis presents simulations of an RF switch using a coplanar waveguide (CPW) with a LC-CNT composite called 4-Cyano-4’-pentylbiphenyl multi-walled nanotube (5CB-MWNT) that is suitable for RF applications. The electrical conductivity modulation and RF switch performance of the 5CB-MWNT composite is determined using Finite Element Analysis (FEA). The simulations will present data on the coplanar waveguide’s s-parameters at the input and output ports S11 and S21 to measure return and insertion loss respectively, two key parameters for determining any RF switch’s performance. Furthermore, this thesis presents applications for improving tunable phased antenna arrays using the LC-CNT composite to allow for beam steering with high-gain and directivity to provide a broad 3D scannable coverage of an area. Tunable antennas are an important characteristic for 5G applications to achieve an optimal telecommunication system to prevent overcrowding of antennas and reduce overall system costs. This research investigates various device geometries with 5CB-MWNT to realize the best performing RF device for RF applications and 5G telecommunication systems. This research presents return and insertion loss data for three waveguide device configurations: CPW, coplanar waveguide grounded (CPWG), and finite ground coplanar waveguide grounded (FG-CPWG). The best results are shown using the CPW configuration. The return loss for the LC-CNT device showed a 5 dB improvement from -7.5 dB to -12.5 dB when using the LC-CNT signal line device. The insertion loss for this configuration showed a much more consistent 0 to -0.3 dB insertion loss value with much less noise when using the LC-CNT device compared to the -0.3 to -1 dB insertion loss value with heavy noise when using the Au signal line device. For the other two configurations the return loss and insertion loss value stayed the same indicating there is no loss in performance when using the LC-CNT switching mechanism. This is ideal due to the benefits that the LC-CNT switching mechanism provides like device reliability and increased switching speeds

Digital Microfluidics as a Reconfiguration Mechanism for Antennas

This dissertation work concentrates on novel reconfiguration technologies, including design, microfabrication, and characterization aspects with an emphasis on their applications to multifunctional reconfigurable antennas. In the literature, reconfigurable antennas have made use of various reconfiguration techniques. The most common techniques utilized revolved around switching mechanisms. Other techniques such as the incorporation of variable capacitors, varactors, and physical structure manipulation surfaced recently to overcome many problems faced in using switches and their biasing. Usage of fluids (micro-fluidic or otherwise) in antennas provides a conceptually easy reconfiguration mechanism in the aspect of physical alteration. However, a requirement of pumps, valves, etc. for liquid transportation makes the antenna implementations rather impractical for the real-life scenarios. This work reports on design and experiments conducted to evaluate the electrowetting on dielectric (EWOD) driven digital microfluidics as a reconfiguration mechanism for antennas

Liquid Metal-Enabled Filtering Switches and Switchplexers

The via-pad-slot (VPS) structure, as the switchable element, has been used to demonstrate a single-pole-triple-throw (SPTT) filtering switch and a switchplexer. The VPS can be flexibily switched using liquid metal (LM) or high dielectric constant materials to either cover or uncover the slot. Since the LM only moves on the surface of the VPS and the substrate-integrated waveguide (SIW), the implementation and actuation of the LM is simple and does not cause excessive loss on the device. In the switchplexer design, all channels can be switched on and off to form filters or multiplexers of various channel combinations. Additional transmission zeros (TZs) can be generated by the loaded, partially switched-off channel. The generation of the TZs was discussed and analyzed using coupling matrix approach. The demonstrated &lt;italic&gt;X&lt;/italic&gt;-band (9.56&amp;#x2013;10.44 GHz) cross-shaped SPTT fifth-order filtering switch exhibits a suppression level of better than 40 dB at 8 and 12 GHz, an insertion loss (IL) of 1.55 dB at 10 GHz, and an isolation level of 58 dB at 10 GHz. The &lt;italic&gt;X&lt;/italic&gt;-band switchplexer operates at three frequency bands, e.g., 11.08&amp;#x2013;11.55 GHz, 10.61&amp;#x2013;10.99 GHz, and 9.76&amp;#x2013;10.33 GHz. The LM-enabled VPS-based switchable element can be integrated with other multifunctional circuits and systems for channel control and reconfiguration.</p

On the Trade-Off Between Quality Factor and Tuning Ratio in Tunable High-Frequency Capacitors

A benchmark of tunable and switchable devices at microwave frequencies is presented on the basis of physical limitations to show their potential for reconfigurable cellular applications. Performance limitations are outlined for each given technology focusing on the quality factor (Q) and tuning ratio (eta) as figures of merit. The state of the art in terms of these figures of merit of several tunable and switchable technologies is visualized and discussed. If the performance of these criteria is not met, the application will not be feasible. The quality factor can typically be traded off for tuning ratio. The benchmark of tunable capacitor technologies shows that transistor-switched capacitors, varactor diodes, and ferroelectric varactors perform well at 2 GHz for tuning ratios below 3, with an advantage for GaAs varactor diodes. Planar microelectromechanical capacitive switches have the potential to outperform all other technologies at tuning ratios higher than 8. Capacitors based on tunable dielectrics have the highest miniaturization potential, whereas semiconductor devices benefit from the existing manufacturing infrastructure