Memory Reliability Enhancement against Multiple Cell Upsets Using Decimal Matrix Code for 32-Bit Data

An important issue in the reliability of memories exposed to radiation environment is transient multiple cells upsets (MCUs). To protect the memory data from radiations and transients many improved packaging techniques are available. But, a particular packaging provides protection from a limited variation of radiations. Today the devices are exposed to a very wide range of environment radiations due to increasing applications in the field of wireless communication. So some additional data preservation techniques are always preferred for authenticating the data before it is processed. Some of these techniques use encoded data to be stored in memories. These techniques are error correction codes (ECCs). It is always preferred to implement an error correction code that requires a less number of redundant bits to be stored and a minimized delay overhead in data correction. This paper presents an FPGA based implementation of memory data error detection and correction code that involves simple decimal addition algorithm in the encoding of data that is to be stored in memory. The decoding of the data for error detection and correction is based on the Hamming Code. This technique involves divide-symbol concept to represent the linear data in groups to make symbolic code. The length of the symbol is inversely proportional to the delay overhead of the cod

New Design Techniques for Dynamic Reconfigurable Architectures

L'abstract è presente nell'allegato / the abstract is in the attachmen

Fault and Defect Tolerant Computer Architectures: Reliable Computing With Unreliable Devices

This research addresses design of a reliable computer from unreliable device technologies. A system architecture is developed for a fault and defect tolerant (FDT) computer. Trade-offs between different techniques are studied and yield and hardware cost models are developed. Fault and defect tolerant designs are created for the processor and the cache memory. Simulation results for the content-addressable memory (CAM)-based cache show 90% yield with device failure probabilities of 3 x 10(-6), three orders of magnitude better than non fault tolerant caches of the same size. The entire processor achieves 70% yield with device failure probabilities exceeding 10(-6). The required hardware redundancy is approximately 15 times that of a non-fault tolerant design. While larger than current FT designs, this architecture allows the use of devices much more likely to fail than silicon CMOS. As part of model development, an improved model is derived for NAND Multiplexing. The model is the first accurate model for small and medium amounts of redundancy. Previous models are extended to account for dependence between the inputs and produce more accurate results

A new architecture for single-event upset detection & reconfiguration of SRAM-based FPGAs

Field Programmable Gate Arrays (FPGA) are used in a variety of applications, ranging from consumer electronics to devices in spacecrafts because of their flexibility in achieving requirements such as low cost, high performance, and fast turnaround. SRAM-based FPGAs can experience single bit flips in the configuration memory due to high-energy neutrons or alpha particles hitting critical nodes in the SRAM cells, by transferring enough energy to effect the change. High energy particles can be emitted by cosmic radiation or traces of radioactive elements in device packaging. The result of this could range from unwanted functional or data modification, data loss in the system, to damage to the cell where the charged particle makes impact. This phenomenon is known as a Single Event Upset (SEU) and makes fault tolerance a critical requirement in FPGA design. This research proposes a shift in architecture from current SRAM-based FPGAs such as Xilinx Virtex. The proposed architecture includes an inherent SEU detection through parity checking of the configuration memory. The inherent SEU detection sets a syndrome flag when an odd number of bit flips occur within a data frame of the configuration memory. To correct a fault, the FPGA the affected data frame is partially reconfigured. Existing and proposed solutions include: Triple Modular Redundancy (TMR) systems; readback and compare the configuration memory; and periodically reprogramming the entire configuration memory, also known as scrubbing. The advantages afforded by the proposed architecture over existing solutions include: faster error detection and correction latency over the readback method and better area and power overhead over TMR

Self-healing concepts involving fine-grained redundancy for electronic systems

The start of the digital revolution came through the metal-oxide-semiconductor field-effect transistor (MOSFET) in 1959 followed by massive integration onto a silicon die by means of constant down scaling of individual components. Digital systems for certain applications require fault-tolerance against faults caused by temporary or permanent influence. The most widely used technique is triple module redundancy (TMR) in conjunction with a majority voter, which is regarded as a passive fault mitigation strategy. Design by functional resilience has been applied to circuit structures for increased fault-tolerance and towards self-diagnostic triggered self-healing. The focus of this thesis is therefore to develop new design strategies for fault detection and mitigation within transistor, gate and cell design levels. The research described in this thesis makes three contributions. The first contribution is based on adding fine-grained transistor level redundancy to logic gates in order to accomplish stuck-at fault-tolerance. The objective is to realise maximum fault-masking for a logic gate with minimal added redundant transistors. In the case of non-maskable stuck-at faults, the gate structure generates an intrinsic indication signal that is suitable for autonomous self-healing functions. As a result, logic circuitry utilising this design is now able to differentiate between gate faults and faults occurring in inter-gate connections. This distinction between fault-types can then be used for triggering selective self-healing responses. The second contribution is a logic matrix element which applies the three core redundancy concepts of spatial- temporal- and data-redundancy. This logic structure is composed of quad-modular redundant structures and is capable of selective fault-masking and localisation depending of fault-type at the cell level, which is referred to as a spatiotemporal quadded logic cell (QLC) structure. This QLC structure has the capability of cellular self-healing. Through the combination of fault-tolerant and masking logic features the QLC is designed with a fault-behaviour that is equal to existing quadded logic designs using only 33.3% of the equivalent transistor resources. The inherent self-diagnosing feature of QLC is capable of identifying individual faulty cells and can trigger self-healing features. The final contribution is focused on the conversion of finite state machines (FSM) into memory to achieve better state transition timing, minimal memory utilisation and fault protection compared to common FSM designs. A novel implementation based on content-addressable type memory (CAM) is used to achieve this. The FSM is further enhanced by creating the design out of logic gates of the first contribution by achieving stuck-at fault resilience. Applying cross-data parity checking, the FSM becomes equipped with single bit fault detection and correction

Synthesis for circuit reliability

textElectrical and Computer Engineerin

Analyse und Erweiterung eines fehler-toleranten NoC für SRAM-basierte FPGAs in Weltraumapplikationen

Data Processing Units for scientific space mission need to process ever higher volumes of data and perform ever complex calculations. But the performance of available space-qualified general purpose processors is just in the lower three digit megahertz range, which is already insufficient for some applications. As an alternative, suitable processing steps can be implemented in hardware on a space-qualified SRAM-based FPGA. However, suitable devices are susceptible against space radiation. At the Institute for Communication and Network Engineering a fault-tolerant, network-based communication architecture was developed, which enables the construction of processing chains on the basis of different processing modules within suitable SRAM-based FPGAs and allows the exchange of single processing modules during runtime, too. The communication architecture and its protocol shall isolate non SEU mitigated or just partial SEU mitigated modules affected by radiation-induced faults to prohibit the propagation of errors within the remaining System-on-Chip. In the context of an ESA study, this communication architecture was extended with further components and implemented in a representative hardware platform. Based on the acquired experiences during the study, this work analyses the actual fault-tolerance characteristics as well as weak points of this initial implementation. At appropriate locations, the communication architecture was extended with mechanisms for fault-detection and fault-differentiation as well as with a hardware-based monitoring solution. Both, the former measures and the extension of the employed hardware-platform with selective fault-injection capabilities for the emulation of radiation-induced faults within critical areas of a non SEU mitigated processing module, are used to evaluate the effects of radiation-induced faults within the communication architecture. By means of the gathered results, further measures to increase fast detection and isolation of faulty nodes are developed, selectively implemented and verified. In particular, the ability of the communication architecture to isolate network nodes without SEU mitigation could be significantly improved.Instrumentenrechner für wissenschaftliche Weltraummissionen müssen ein immer höheres Datenvolumen verarbeiten und immer komplexere Berechnungen ausführen. Die Performanz von verfügbaren qualifizierten Universalprozessoren liegt aber lediglich im unteren dreistelligen Megahertz-Bereich, was für einige Anwendungen bereits nicht mehr ausreicht. Als Alternative bietet sich die Implementierung von entsprechend geeigneten Datenverarbeitungsschritten in Hardware auf einem qualifizierten SRAM-basierten FPGA an. Geeignete Bausteine sind jedoch empfindlich gegenüber der Strahlungsumgebung im Weltraum. Am Institut für Datentechnik und Kommunikationsnetze wurde eine fehlertolerante netzwerk-basierte Kommunikationsarchitektur entwickelt, die innerhalb eines geeigneten SRAM-basierten FPGAs Datenverarbeitungsmodule miteinander nach Bedarf zu Verarbeitungsketten verbindet, sowie den Austausch von einzelnen Modulen im Betrieb ermöglicht. Nicht oder nur partiell SEU mitigierte Module sollen bei strahlungsbedingten Fehlern im Modul durch das Protokoll und die Fehlererkennungsmechanismen der Kommunikationsarchitektur isoliert werden, um ein Ausbreiten des Fehlers im restlichen System-on-Chip zu verhindern. Im Kontext einer ESA Studie wurde diese Kommunikationsarchitektur um Komponenten erweitert und auf einer repräsentativen Hardwareplattform umgesetzt. Basierend auf den gesammelten Erfahrungen aus der Studie, wird in dieser Arbeit eine Analyse der tatsächlichen Fehlertoleranz-Eigenschaften sowie der Schwachstellen dieser ursprünglichen Implementierung durchgeführt. Die Kommunikationsarchitektur wurde an geeigneten Stellen um Fehlerdetektierungs- und Fehlerunterscheidungsmöglichkeiten erweitert, sowie um eine hardwarebasierte Überwachung ergänzt. Sowohl diese Maßnahmen, als auch die Erweiterung der Hardwareplattform um gezielte Fehlerinjektions-Möglichkeiten zum Emulieren von strahlungsinduzierten Fehlern in kritischen Komponenten eines nicht SEU mitigierten Prozessierungsmoduls werden genutzt, um die tatsächlichen auftretenden Effekte in der Kommunikationsarchitektur zu evaluieren. Anhand der Ergebnisse werden weitere Verbesserungsmaßnahmen speziell zur schnellen Detektierung und Isolation von fehlerhaften Knoten erarbeitet, selektiv implementiert und verifiziert. Insbesondere die Fähigkeit, fehlerhafte, nicht SEU mitigierte Netzwerkknoten innerhalb der Kommunikationsarchitektur zu isolieren, konnte dabei deutlich verbessert werden

Fault-tolerant fpga for mission-critical applications.

One of the devices that play a great role in electronic circuits design, specifically safety-critical design applications, is Field programmable Gate Arrays (FPGAs). This is because of its high performance, re-configurability and low development cost. FPGAs are used in many applications such as data processing, networks, automotive, space and industrial applications. Negative impacts on the reliability of such applications result from moving to smaller feature sizes in the latest FPGA architectures. This increases the need for fault-tolerant techniques to improve reliability and extend system lifetime of FPGA-based applications. In this thesis, two fault-tolerant techniques for FPGA-based applications are proposed with a built-in fault detection region. A low cost fault detection scheme is proposed for detecting faults using the fault detection region used in both schemes. The fault detection scheme primarily detects open faults in the programmable interconnect resources in the FPGAs. In addition, Stuck-At faults and Single Event Upsets (SEUs) fault can be detected. For fault recovery, each scheme has its own fault recovery approach. The first approach uses a spare module and a 2-to-1 multiplexer to recover from any fault detected. On the other hand, the second approach recovers from any fault detected using the property of Partial Reconfiguration (PR) in the FPGAs. It relies on identifying a Partially Reconfigurable block (P_b) in the FPGA that is used in the recovery process after the first faulty module is identified in the system. This technique uses only one location to recover from faults in any of the FPGA’s modules and the FPGA interconnects. Simulation results show that both techniques can detect and recover from open faults. In addition, Stuck-At faults and Single Event Upsets (SEUs) fault can also be detected. Finally, both techniques require low area overhead

SABRE: A bio-inspired fault-tolerant electronic architecture

As electronic devices become increasingly complex, ensuring their reliable, fault-free operation is becoming correspondingly more challenging. It can be observed that, in spite of their complexity, biological systems are highly reliable and fault tolerant. Hence, we are motivated to take inspiration for biological systems in the design of electronic ones. In SABRE (self-healing cellular architectures for biologically inspired highly reliable electronic systems), we have designed a bio-inspired fault-tolerant hierarchical architecture for this purpose. As in biology, the foundation for the whole system is cellular in nature, with each cell able to detect faults in its operation and trigger intra-cellular or extra-cellular repair as required. At the next level in the hierarchy, arrays of cells are configured and controlled as function units in a transport triggered architecture (TTA), which is able to perform partial-dynamic reconfiguration to rectify problems that cannot be solved at the cellular level. Each TTA is, in turn, part of a larger multi-processor system which employs coarser grain reconfiguration to tolerate faults that cause a processor to fail. In this paper, we describe the details of operation of each layer of the SABRE hierarchy, and how these layers interact to provide a high systemic level of fault tolerance. © 2013 IOP Publishing Ltd