VLSI Implementation of a Soft-Output Signal Detector for Multi-Mode Adaptive MIMO Systems

This paper presents a multimode soft-output multiple-input multiple-output (MIMO) signal detector that is efficient in hardware cost and energy consumption. The detector is capable of dealing with spatial-multiplexing (SM),break space-division-multiple-access (SDMA), and spatial-diversity (SD) signals of 4 ✕ 4 antenna and 64-QAM modulation. Implementation-friendly algorithms, which reuse most of the mathematical operations in these three MIMO modes, are proposed to provide accurate soft detection information, i.e., log-likelihood ratio, with much reduced complexity. A unified reconfigurable VLSI architecture has been developed to eliminate the implementation of multiple detector modules. In addition, several block level technologies, such as parallel metric update and fast bit-flipping, are adopted to enable a more efficient design. To evaluate the proposed techniques, we implemented the triple-mode MIMO detector in a 65-nm CMOS technology. The core area is 0.25 mm2 with 83.7 K gates. The maximum detecting throughput is 1 Gb/s at 167-MHz clock frequency and 1.2-V supply, which archives the data rate envisioned by the emerging long-term evolution advanced standard. Under frequency-selective channels, the detector consumes 59.3-, 10.5-, and 169.6-pJ energy per bit detection in SM, SD, and SDMA modes, respectively

A Continuous-Time Recurrent Neural Network for Joint Equalization and Decoding – Analog Hardware Implementation Aspects

Equalization and channel decoding are “traditionally” two cascade processes at the receiver side of a digital transmission. They aim to achieve a reliable and efficient transmission. For high data rates, the energy consumption of their corresponding algorithms is expected to become a limiting factor. For mobile devices with limited battery’s size, the energy consumption, mirrored in the lifetime of the battery, becomes even more crucial. Therefore, an energy-efficient implementation of equalization and decoding algorithms is desirable. The prevailing way is by increasing the energy efficiency of the underlying digital circuits. However, we address here promising alternatives offered by mixed (analog/digital) circuits. We are concerned with modeling joint equalization and decoding as a whole in a continuous-time framework. In doing so, continuous-time recurrent neural networks play an essential role because of their nonlinear characteristic and special suitability for analog very-large-scale integration (VLSI). Based on the proposed model, we show that the superiority of joint equalization and decoding (a well-known fact from the discrete-time case) preserves in analog. Additionally, analog circuit design related aspects such as adaptivity, connectivity and accuracy are discussed and linked to theoretical aspects of recurrent neural networks such as Lyapunov stability and simulated annealing

Baseband Processing for 5G and Beyond: Algorithms, VLSI Architectures, and Co-design

In recent years the number of connected devices and the demand for high data-rates have been significantly increased. This enormous growth is more pronounced by the introduction of the Internet of things (IoT) in which several devices are interconnected to exchange data for various applications like smart homes and smart cities. Moreover, new applications such as eHealth, autonomous vehicles, and connected ambulances set new demands on the reliability, latency, and data-rate of wireless communication systems, pushing forward technology developments. Massive multiple-input multiple-output (MIMO) is a technology, which is employed in the 5G standard, offering the benefits to fulfill these requirements. In massive MIMO systems, base station (BS) is equipped with a very large number of antennas, serving several users equipments (UEs) simultaneously in the same time and frequency resource. The high spatial multiplexing in massive MIMO systems, improves the data rate, energy and spectral efficiencies as well as the link reliability of wireless communication systems. The link reliability can be further improved by employing channel coding technique. Spatially coupled serially concatenated codes (SC-SCCs) are promising channel coding schemes, which can meet the high-reliability demands of wireless communication systems beyond 5G (B5G). Given the close-to-capacity error correction performance and the potential to implement a high-throughput decoder, this class of code can be a good candidate for wireless systems B5G. In order to achieve the above-mentioned advantages, sophisticated algorithms are required, which impose challenges on the baseband signal processing. In case of massive MIMO systems, the processing is much more computationally intensive and the size of required memory to store channel data is increased significantly compared to conventional MIMO systems, which are due to the large size of the channel state information (CSI) matrix. In addition to the high computational complexity, meeting latency requirements is also crucial. Similarly, the decoding-performance gain of SC-SCCs also do come at the expense of increased implementation complexity. Moreover, selecting the proper choice of design parameters, decoding algorithm, and architecture will be challenging, since spatial coupling provides new degrees of freedom in code design, and therefore the design space becomes huge. The focus of this thesis is to perform co-optimization in different design levels to address the aforementioned challenges/requirements. To this end, we employ system-level characteristics to develop efficient algorithms and architectures for the following functional blocks of digital baseband processing. First, we present a fast Fourier transform (FFT), an inverse FFT (IFFT), and corresponding reordering scheme, which can significantly reduce the latency of orthogonal frequency-division multiplexing (OFDM) demodulation and modulation as well as the size of reordering memory. The corresponding VLSI architectures along with the application specific integrated circuit (ASIC) implementation results in a 28 nm CMOS technology are introduced. In case of a 2048-point FFT/IFFT, the proposed design leads to 42% reduction in the latency and size of reordering memory. Second, we propose a low-complexity massive MIMO detection scheme. The key idea is to exploit channel sparsity to reduce the size of CSI matrix and eventually perform linear detection followed by a non-linear post-processing in angular domain using the compressed CSI matrix. The VLSI architecture for a massive MIMO with 128 BS antennas and 16 UEs along with the synthesis results in a 28 nm technology are presented. As a result, the proposed scheme reduces the complexity and required memory by 35%–73% compared to traditional detectors while it has better detection performance. Finally, we perform a comprehensive design space exploration for the SC-SCCs to investigate the effect of different design parameters on decoding performance, latency, complexity, and hardware cost. Then, we develop different decoding algorithms for the SC-SCCs and discuss the associated decoding performance and complexity. Also, several high-level VLSI architectures along with the corresponding synthesis results in a 12 nm process are presented, and various design tradeoffs are provided for these decoding schemes

Center for Aeronautics and Space Information Sciences

This report summarizes the research done during 1991/92 under the Center for Aeronautics and Space Information Science (CASIS) program. The topics covered are computer architecture, networking, and neural nets

Iterative decoding for MIMO channels via modified sphere decoding

In recent years, soft iterative decoding techniques have been shown to greatly improve the bit error rate performance of various communication systems. For multiantenna systems employing space-time codes, however, it is not clear what is the best way to obtain the soft information required of the iterative scheme with low complexity. In this paper, we propose a modification of the Fincke-Pohst (sphere decoding) algorithm to estimate the maximum a posteriori probability of the received symbol sequence. The new algorithm solves a nonlinear integer least squares problem and, over a wide range of rates and signal-to-noise ratios, has polynomial-time complexity. Performance of the algorithm, combined with convolutional, turbo, and low-density parity check codes, is demonstrated on several multiantenna channels. The results for systems that employ space-time modulation schemes seem to indicate that the best performing schemes are those that support the highest mutual information between the transmitted and received signals, rather than the best diversity gain

Enabling VLSI processing blocks for MIMO-OFDM Communications

Multi-input multi-output (MIMO) systems combined with orthogonal frequency-division multiplexing (OFDM) gained a wide popularity in wireless applications due to the potential of providing increased channel capacity and robustness against multipath fading channels. However these advantages come at the cost of a very high processing complexity and the efficient implementation of MIMO-OFDM receivers is today a major research topic. In this paper, efficient architectures are proposed for the hardware implementation of the main building blocks of a MIMO-OFDM receiver. A sphere decoder architecture flexible to different modulation without any loss in BER performance is presented while the proposed matrix factorization implementation allows to achieve the highest throughput specified in the IEEE 802.11n standard. Finally a novel sphere decoder approach is presented, which allows for the realization of new golden space time trellis coded modulation (GST-TCM) scheme. Implementation cost and offered throughput are provided for the proposed architectures synthesized on a 0.13  CMOS standard cell technology or on advanced FPGA devices

A Survey on the Best Choice for Modulus of Residue Code

Nowadays, the development of technology and the growing need for dense and complex chips have led chip industries to increase their attention on the circuit testability. Also, using the electronic chips in certain industries, such as the space industry, makes the design of fault tolerant circuits a challenging issue. Coding is one of the most suitable methods for error detection and correction. The residue code, as one of the best choices for error detection aims, is wildly used in large arithmetic circuits such as multiplier and also finds a wide range of applications in processors and digital filters. The modulus value in this technique directly effect on the area overhead parameter. A large area overhead is one of the most important disadvantages especially for testing the small circuits. The purpose of this paper is to study and investigate the best choice for residue code check base that is used for simple and small circuits such as a simple ripple carry adder. The performances are evaluated by applying stuck-at-faults and transition-faults by simulators. The efficiency is defined based on fault coverage and normalized area overhead. The results show that the modulus 3 with 95% efficiency provided the best result. Residue code with this modulus for checking a ripple carry adder, in comparison with duplex circuit, 30% improves the efficiency

Spread Spectrum Watermarking: Principles and Applications in Fading Channel

ISBN 978-953-51-0618-