ATPG for Delay Defects in Current Mode Threshold Logic Circuits

An automatic test pattern generation approach todetect delay defects in a circuit consisting of current modethreshold logic gates is introduced. Each generated patternshould excite the maximum propagation delay at the fault site.Manufactured weights may vary, and maximum delay is ensuredby applying an appropriately generated set of patterns per fault.Experimental results show the efficiency of the proposed methods

A comprehensive comparison between design for testability techniques for total dose testing of flash-based FPGAs

Radiation sources exist in different kinds of environments where electronic devices often operate. Correct device operation is usually affected negatively by radiation. The radiation resultant effect manifests in several forms depending on the operating environment of the device like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). CMOS circuits and Floating gate MOS circuits suffer from an increase in the delay and the leakage current due to TID effect. This may damage the proper operation of the integrated circuit. Exhaustive testing is needed for devices operating in harsh conditions like space and military applications to ensure correct operations in the worst circumstances. The use of worst case test vectors (WCTVs) for testing is strongly recommended by MIL-STD-883, method 1019, which is the standard describing the procedure for testing electronic devices under radiation. However, the difficulty of generating these test vectors hinders their use in radiation testing. Testing digital circuits in the industry is usually done nowadays using design for testability (DFT) techniques as they are very mature and can be relied on. DFT techniques include, but not limited to, ad-hoc technique, built-in self test (BIST), muxed D scan, clocked scan and enhanced scan. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Despite all these recommendations for DFT, radiation testing has not benefited from this reliable technology yet. Also, with the big variation in the DFT techniques, choosing the right technique is the bottleneck to achieve the best results for TID testing. In this thesis, a comprehensive comparison between different DFT techniques for TID testing of flash-based FPGAs is made to help designers choose the best suitable DFT technique depending on their application. The comparison includes muxed D scan technique, clocked scan technique and enhanced scan technique. The comparison is done using ISCAS-89 benchmarks circuits. Points of comparisons include FPGA resources utilization, difficulty of designs bring-up, added delay by DFT logic and robust testable paths in each technique

Identifying worst case test vectors for FPGA exposed to total ionization dose using design for testability techniques

Electronic devices often operate in harsh environments which contain a variation of radiation sources. Radiation may cause different kinds of damage to proper operation of the devices. Their sources can be found in terrestrial environments, or in extra-terrestrial environments like in space, or in man-made radiation sources like nuclear reactors, biomedical devices and high energy particles physics experiments equipment. Depending on the operation environment of the device, the radiation resultant effect manifests in several forms like total ionizing dose effect (TID), or single event effects (SEEs) such as single event upset (SEU), single event gate rupture (SEGR), and single event latch up (SEL). TID effect causes an increase in the delay and the leakage current of CMOS circuits which may damage the proper operation of the integrated circuit. To ensure proper operation of these devices under radiation, thorough testing must be made especially in critical applications like space and military applications. Although the standard which describes the procedure for testing electronic devices under radiation emphasizes the use of worst case test vectors (WCTVs), they are never used in radiation testing due to the difficulty of generating these vectors for circuits under test. For decades, design for testability (DFT) has been the best choice for test engineers to test digital circuits in industry. It has become a very mature technology that can be relied on. DFT is usually used with automatic test patterns generation (ATPG) software to generate test vectors to test application specific integrated circuits (ASICs), especially with sequential circuits, against faults like stuck at faults and path delay faults. Surprisingly, however, radiation testing has not yet made use of this reliable technology. In this thesis, a novel methodology is proposed to extend the usage of DFT to generate WCTVs for delay failure in Flash based field programmable gate arrays (FPGAs) exposed to total ionizing dose (TID). The methodology is validated using MicroSemi ProASIC3 FPGA and cobalt 60 facility

Investigation into voltage and process variation-aware manufacturing test

Increasing integration and complexity in IC design provides challenges for manufacturing testing. This thesis studies how process and supply voltage variation influence defect behaviour to determine the impact on manufacturing test cost and quality. The focus is on logic testing of static CMOS designs with respect to two important defect types in deep submicron CMOS: resistive bridges and full opens. The first part of the thesis addresses testing for resistive bridge defects in designs with multiple supply voltage settings. To enable analysis, a fault simulator is developed using a supply voltage-aware model for bridge defect behaviour. The analysis shows that for high defect coverage it is necessary to perform test for more than one supply voltage setting, due to supply voltage-dependent behaviour. A low-cost and effective test method is presented consisting of multi-voltage test generation that achieves high defect coverage and test set size reduction without compromise to defect coverage. Experiments on synthesised benchmarks with realistic bridge locations validate the proposed method.The second part focuses on the behaviour of full open defects under supply voltage variation. The aim is to determine the appropriate value of supply voltage to use when testing. Two models are considered for the behaviour of full open defects with and without gate tunnelling leakage influence. Analysis of the supply voltage-dependent behaviour of full open defects is performed to determine if it is required to test using more than one supply voltage to detect all full open defects. Experiments on synthesised benchmarks using an extended version of the fault simulator tool mentioned above, measure the quantitative impact of supply voltage variation on defect coverage.The final part studies the impact of process variation on the behaviour of bridge defects. Detailed analysis using synthesised ISCAS benchmarks and realistic bridge model shows that process variation leads to additional faults. If process variation is not considered in test generation, the test will fail to detect some of these faults, which leads to test escapes. A novel metric to quantify the impact of process variation on test quality is employed in the development of a new test generation tool, which achieves high bridge defect coverage. The method achieves a user-specified test quality with test sets which are smaller than test sets generated without consideration of process variation

Improving timing verification and delay testing methodologies for IC designs

textThe task of ensuring the correct temporal behavior of IC designs, both before and after fabrication, is extremely important. It is becoming even more imperative as the demand for performance increases and process technology advances into the deep sub-micron region. This dissertation tackles the key issues in the timing verification and delay testing methodologies. An efficient methodology is presented to identify false timing paths in the timing verification methodology which utilizes ATPG technique and timing information from an ordered list of timing paths according to the delay information. This dissertation also presents a speed binning methodology which utilizes structural delay tests successfully instead of functional tests. In addition, it establishes a methodology which quantifies the correlation between the timing verification prediction and actual silicon measurement of timing paths. This quantification methodology lays the foundation for further research to study the impact of deep submicron effects on design performanceElectrical and Computer Engineerin

Testability considerations for implementing an embedded memory subsystem

textThere are a number of testability considerations for VLSI design, but test coverage, test time, accuracy of test patterns and correctness of design information for DFD (Design for debug) are the most important ones in design with embedded memories. The goal of DFT (Design-for-Test) is to achieve zero defects. When it comes to the memory subsystem in SOCs (system on chips), many flavors of memory BIST (built-in self test) are able to get high test coverage in a memory, but often, no proper attention is given to the memory interface logic (shadow logic). Functional testing and BIST are the most prevalent tests for this logic, but functional testing is impractical for complicated SOC designs. As a result, industry has widely used at-speed scan testing to detect delay induced defects. Compared with functional testing, scan-based testing for delay faults reduces overall pattern generation complexity and cost by enhancing both controllability and observability of flip-flops. However, without proper modeling of memory, Xs are generated from memories. Also, when the design has chip compression logic, the number of ATPG patterns is increased significantly due to Xs from memories. In this dissertation, a register based testing method and X prevention logic are presented to tackle these problems. An important design stage for scan based testing with memory subsystems is the step to create a gate level model and verify with this model. The flow needs to provide a robust ATPG netlist model. Most industry standard CAD tools used to analyze fault coverage and generate test vectors require gate level models. However, custom embedded memories are typically designed using a transistor-level flow, there is a need for an abstraction step to generate the gate models, which must be equivalent to the actual design (transistor level). The contribution of the research is a framework to verify that the gate level representation of custom designs is equivalent to the transistor-level design. Compared to basic stuck-at fault testing, the number of patterns for at-speed testing is much larger than for basic stuck-at fault testing. So reducing test and data volume are important. In this desertion, a new scan reordering method is introduced to reduce test data with an optimal routing solution. With in depth understanding of embedded memories and flows developed during the study of custom memory DFT, a custom embedded memory Bit Mapping method using a symbolic simulator is presented in the last chapter to achieve high yield for memories.Electrical and Computer Engineerin