Antenna Design for 5G and Beyond

With the rapid evolution of the wireless communications, fifth-generation (5G) communication has received much attention from both academia and industry, with many reported efforts and research outputs and significant improvements in different aspects, such as data rate speed and resolution, mobility, latency, etc. In some countries, the commercialization of 5G communication has already started as well as initial research of beyond technologies such as 6G.MIMO technology with multiple antennas is a promising technology to obtain the requirements of 5G/6G communications. It can significantly enhance the system capacity and resist multipath fading, and has become a hot spot in the field of wireless communications. This technology is a key component and probably the most established to truly reach the promised transfer data rates of future communication systems. In MIMO systems, multiple antennas are deployed at both the transmitter and receiver sides. The greater number of antennas can make the system more resistant to intentional jamming and interference. Massive MIMO with an especially high number of antennas can reduce energy consumption by targeting signals to individual users utilizing beamforming.Apart from sub-6 GHz frequency bands, 5G/6G devices are also expected to cover millimeter-wave (mmWave) and terahertz (THz) spectra. However, moving to higher bands will bring new challenges and will certainly require careful consideration of the antenna design for smart devices. Compact antennas arranged as conformal, planar, and linear arrays can be employed at different portions of base stations and user equipment to form phased arrays with high gain and directional radiation beams. The objective of this Special Issue is to cover all aspects of antenna designs used in existing or future wireless communication systems. The aim is to highlight recent advances, current trends, and possible future developments of 5G/6G antennas

3D-Printable Dielectric Transmitarray With Enhanced Bandwidth at Millimeter-Waves

In this paper, a three-layer dielectric structure is presented as innovative unit-cell element for transmitarray (TA) antennas with enhanced bandwidth. It consists of a central layer, with a varying size square hole, used to compensate the phase of the incident field and located between two other identical layers with linearly tapered square holes, acting as matching circuits. The effectiveness of this unit-cell is demonstrated by the numerical and the experimental results here presented. As a first step, three different TAs with increasing size are designed and simulated: their 1-dB gain bandwidth, centered at 30 GHz, varies from the 30.9% of the smallest configuration, having size of $10\lambda _{0}\times 10\lambda _{0}$ , to the 17.5% of the $20\lambda _{0}\times 20\lambda _{0}$ TA. A slightly modified unit-cell is then designed, with the aim of realizing a prototype with an additive manufacturing (AM) technique. A 3D-printed dielectric TA with a size of $15.6\lambda _{0}\times 15.6\lambda _{0}$ has been manufactured and experimentally characterized. The measured prototype shows excellent performances, achieving a 1-dB gain bandwidth of 21.5%: these results prove the enhanced features of the introduced unit-cell and demonstrate the TA feasibility with AM techniques

Circularly polarized and reconfigurable frequency selective surface based transmit array antenna for x-band applications

Transmitarray (TA) antennas have attracted much attention in recent years due to their number of applications. These include the 5G/6G mobile networks and satellite communication systems for the microwave frequency range. The various satellite applications require high-gain antennas with polarization agility. Also, the state-ofthe- art smart communication systems require reconfigurable antennas allowing the frequency and beam switching according to the application requirements. In this research, three different TA antennas have been studied and designed for X-band applications which are high gain and wideband TA antenna, circularly polarized TA antenna, frequency and beam reconfigurable TA antenna. For the first design, two Frequency-Selective Surface (FSS) unit cells which include Double Square Ring with Center Patch (DSR-CP) and Split Ring Resonator (SRR), have been applied to increase the antenna gain and bandwidth. The optimized unit cell structure shows that a fourlayer configuration could provide maximum phase range with low insertion losses. The complete DSR-CP TA consisting of 121 elements has produced an impedance bandwidth of 33.3% with a peak gain value of 20.4 dBi and 1-dB gain for bandwidth of 10%. SRR-based TA achieved the impedance bandwidth of 35% with a peak gain value of 21.9 dBi and 11.6% 1-dB gain bandwidth. A circularly polarized TA using a Meander Line Polarizer (MLP) superstrate has been studied and presented. The MLP unit cell was simulated and optimized at 12 GHz, having 900 phase difference between the two orthogonal E-field components, Ex and Ey. The final prototype measurement results show that a low axial ratio of 1.89 and 20.17 dBi gain at 11.2 GHz has been obtained. Finally, the last part of the research focused on the frequency and beam reconfigurable TA antenna. A U-shape superstrate layer has been added to introduce frequency selectivity in front of the horn antenna that acts as a bandpass filter. Then, by varying the strip length of the U-shape unit cell, the antenna frequency can be reconfigured from 8.5 GHz to 11.2 GHz. On the other hand, a new active TA unit cell equipped with four switchable strips using Positive Intrinsic Negative (PIN) diodes has been employed to achieve beam reconfigurable TA antenna. Thus, the antenna beam can be tilted by controlling the PIN diodes ON and OFF switching states. Results show that a full-beam switching range of 43.20 has been obtained. In conclusion, this research has successfully presented three new TA antenna designs, which are highly potential for the X-band applications

Reconfigurable Reflectarrays and Array Lenses for Dynamic Antenna Beam Control: A Review

Advances in reflectarrays and array lenses with electronic beam-forming capabilities are enabling a host of new possibilities for these high-performance, low-cost antenna architectures. This paper reviews enabling technologies and topologies of reconfigurable reflectarray and array lens designs, and surveys a range of experimental implementations and achievements that have been made in this area in recent years. The paper describes the fundamental design approaches employed in realizing reconfigurable designs, and explores advanced capabilities of these nascent architectures, such as multi-band operation, polarization manipulation, frequency agility, and amplification. Finally, the paper concludes by discussing future challenges and possibilities for these antennas.Comment: 16 pages, 12 figure

透過アレーアンテナの高性能化と多機能化に関する研究

Tohoku University陳強課

X-band rectangular to square waveguide transition for transmitarray unit cell characterization

In this paper, a characterization setup for transmitarray unit cell analysis is designed in CST studio using rectangular to square waveguide transition for X-band applications. A wideband transmitarray unit cell is designed using split ring resonator and unit cell simulations show wide impedance matching bandwidth of 43.7%. In this simulation, the waveguide transition length is varied to reduce the reflection coefficient magnitudes below -20dB. Then, the square cross section area of waveguide is made variable and cutoff frequency variation over 4GHz is illustrated. Finally, the model for real time test setup is simulated along with the transmitarray unit cell and the results show high transmission magnitude of -O.23dB. This setup can also be used for other frequency selective surface unit cells characterization

Conformal Transmitarrays for Unmanned Aerial Vehicles Aided 6G Networks

Unmanned aerial vehicles (UAVs) aided wireless communications promise to provide high-speed cost-effective wireless connectivity without needing fixed infrastructure coverage. They are a key technology enabler for sixth generation (6G) wireless networks, where a three-dimensional coverage including space, aero and terrestrial networks are to be deployed to guarantee seamless service continuity and reliability. Owing to the aerodynamic requirements, it is highly desirable to employ conformal antennas that can follow the shapes of the UAVs to reduce the extra drag and fuel consumption. To enable hundred giga-bits-per-second (Gb/s) data rates and massive connectivity for 6G networks, conformal antenna arrays featured with high gains and beam scanning/multiple beams are demanded for millimeter-wave and higher-frequency-range communications. However, new challenges exist in designing and implementing high-gain conformal arrays for UAV platforms. In this article, we overview the recent advances in conformal transmitarrays for UAV-based wireless communications, introducing new design methodologies and high-lighting new opportunities to be exploited

Quasi-Optical Multi-Beam Antenna Technologies for B5G and 6G mmWave and THz Networks: A Review

Multi-beam antennas are critical components in future terrestrial and non-terrestrial wireless communications networks. The multiple beams produced by these antennas will enable dynamic interconnection of various terrestrial, airborne and space-borne network nodes. As the operating frequency increases to the high millimeter wave (mmWave) and terahertz (THz) bands for beyond 5G (B5G) and sixth-generation (6G) systems, quasi-optical techniques are expected to become dominant in the design of high gain multi-beam antennas. This paper presents a timely overview of the mainstream quasi-optical techniques employed in current and future multi-beam antennas. Their operating principles and design techniques along with those of various quasi-optical beamformers are presented. These include both conventional and advanced lens and reflector based configurations to realize high gain multiple beams at low cost and in small form factors. New research challenges and industry trends in the field, such as planar lenses based on transformation optics and metasurface-based transmitarrays, are discussed to foster further innovations in the microwave and antenna research community