Direct usage of photovoltaic solar panels to supply a freezer motor with variable DC input voltage

In this paper, a single-phase photovoltaic (PV) inverter fed by a boost converter to supply a freezer motor with variable DC input is investigated. The proposed circuit has two stages. Firstly, the DC output of the PV panel that varies between 150 and 300 V will be applied to the boost converter. The boost converter will boost the input voltage to a fixed 300 V DC. Next, this voltage is supplied to the single-phase full-bridge inverter to obtain 230 V AC. In the end, The output of the inverter will feed a freezer motor. The PV panels can be stand-alone or grid-connected. The grid-connected PV is divided into two categories, such as with a transformer and without a transformer, a transformer type has galvanic isolation resulting in increasing the security and also provides no further DC current toward the grid, but it is expensive, heavy and bulky. The transformerless type holds high efficiency and it is cheaper, but it suffers from leakage current between PV and the grid. This paper proposes a stand-alone direct use of PV to supply a freezer; therefore, no grid connection will result in no leakage current between the PV and Grid. The proposed circuit has some features such as no filtering circuit at the output of the inverter, no battery in the system, DC-link instead of AC link that reduces no-loads, having a higher efficiency, and holding enough energy in the DC-link capacitor to get the motor started. The circuit uses no transformers, thus, it is cheaper and has a smaller size. In addition, the system does not require a complex pulse width modulation (PWM) technique, because the motor can operate with a pulsed waveform. The control strategy uses the PWM signal with the desired timing. With this type of square wave, the harmonics (5th and 7th) of the voltage are reduced. The experimental and simulation results are presented to verify the feasibility of the proposed strategy

A hybrid multilevel converter for medium and high voltage applications

This paper investigates the suitability of the hybrid multilevel converter for medium and high voltage application. The converter operation, modulation, and capacitor voltage balancing method are described in detail. The ability of the hybrid multilevel converter to operate with different modulation indices and load power factors is investigated. It has been established that the hybrid multilevel converter is capable of operating independent of load power factor. Operation with variable modulation index increases voltage stresses on the converter switches and does not alter the fundamental voltage magnitude as in all known voltage source converter topologies. The viability of the hybrid multilevel converter for medium and high voltage applications is confirmed by simulations

Solar Photovoltaic and Thermal Energy Systems: Current Technology and Future Trends

Solar systems have become very competitive solutions for residential, commercial, and industrial applications for both standalone and grid connected operations. This paper presents an overview of the current status and future perspectives of solar energy (mainly photovoltaic) technology and the required conversion systems. The focus in the paper is put on the current technology, installations challenges, and future expectations. Various aspects related to the global solar market, the photovoltaic (PV) modules cost and technology, and the power electronics converter systems are addressed. Research trends and recommendations for each of the PV system sectors are also discussed.Junta de Andalucía P11-TIC-7070Ministerio de Ciencia e Innovación TEC2016-78430-

New Topologies and Advanced Control of Power Electronic Converters for Renewable Energy based Microgrids

Solar energy-based microgrids are increasingly promising due to their many features, such as being environmentally friendly and having low operating costs. Power electronic converters, filters, and transformers are the key components to integrate the solar photovoltaic (PV) systems with the microgrids. The power electronic converters play an important role to reduce the size of the filter circuit and eliminate the use of the bulky and heavy traditional power frequency step-up transformer. These power converters also play a vital role to integrate the energy storage systems such as batteries and the superconducting magnetic energy storage (SMES) unit in a solar PV power-based microgrid. However, the performance of these power converters depends upon the switching technique and the power converter configuration. The switching techniques can improve the power quality, i.e. lower total harmonic distortion at the converter output waveform, reduce the converter power loss, and can effectively utilize the dc bus voltage, which helps to improve the power conversion efficiency of the power electronic converter. The power converter configuration can reduce the size of the power converter and make the power conversion system more efficient. In addition to the advanced switching technique, a supervisory control can also be integrated with these power converters to ensure the optimal power flow within the microgrid. First, this thesis reviews different existing power converter topologies with their switching techniques and control strategies for the grid integration of solar PV systems. To eliminate the use of the bulky and heavy line frequency step-up transformer to integrate solar PV systems to medium voltage grids, the high frequency magnetic linkbased medium voltage power converter topologies are discussed and compared based on their performance parameters. Moreover, switching and conduction losses are calculated to compare the performance of the switching techniques for the magnetic-linked power converter topologies. In this thesis, a new pulse width modulation technique has been proposed to integrate the SMES system with the solar PV system-based microgrid. The pulse width modulation technique is designed to provide reactive power into the network in an effective way. The modulation technique ensures lower total harmonic distortion (THD), lower switching loss, and better utilization of dc-bus voltage. The simulation and experimental results show the effectiveness of the proposed pulse width modulation technique. In this thesis, an improved version of the previously proposed switching technique has been designed for a transformer-less PV inverter. The improved switching technique can ensure effective active power flow into the network. A new switching scheme has been proposed for reactive power control to avoid unnecessary switching faced by the traditional switching technique in a transformer-less PV inverter. The proposed switching technique is based on the peak point value of the grid current and ensures lower switching loss compared to other switching techniques. In this thesis, a new magnetic-linked multilevel inverter has been designed to overcome the issues faced by the two-level inverters and traditional multilevel inverters. The proposed multilevel inverter utilizes the same number of electronic switches but fewer capacitors compared to the traditional multilevel inverters. The proposed multilevel inverter solves the capacitor voltage balancing and utilizes 25% more of the dc bus voltage compared to the traditional multilevel inverter, which reduces the power rating of the dc power source components and also extends the input voltage operating range of the inverter. An improved version magnetic-linked multilevel inverter is proposed in this thesis with a model predictive control technique. This multilevel inverter reduces both the number of switches and capacitors compared to the traditional multilevel inverter. This multilevel inverter also solves the capacitor voltage balancing issue and utilizes 50% more of the dc bus voltage compared to the traditional multilevel inverter. Finally, an energy management system has been designed for the developed power converter and control to achieve energy resiliency and minimum operating cost of the microgrid. The model predictive control-based energy management system utilizes the predicted load data, PV insolation data from web service, electricity price data, and battery state of charge data to select the battery charging and discharging pattern over the day. This model predictive control-based supervisory control with the advanced power electronic converter and control makes the PV energy-based microgrid more efficient and reliable

Analysis, Design, and Control of a Single-Phase Single-Stage Grid-Connected Transformerless Solar Inverter

As energy utilization is increasing with the rise in the world’s power demand, the traditional energy sources are depleting at a high pace. It has led to attention drawn towards inexhaustible energy resources. There is a huge augmentation in the power generation from renewable energy sources (RES) like wind, solar, hydropower, biomass, etc. to reduce the stress on conventional energy sources like fossil fuels, oil, gas, etc. There has been a steep increase in interest for wind and solar energy systems. PV energy has been growing swiftly in the past two decades which made it most demanded power generation system based on RES. This worldwide requirement for solar energy has led to an immense amount of innovation and development in the Photovoltaic (PV) market. The Conventional grid-connected PV inverter was either with DC/DC converter or without DC/DC converter. These inverters were isolated using a transformer either on the grid (AC) side as a low-frequency transformer or as a high-frequency transformer on the DC side. Elimination of the transformer leads to a galvanic connection between the grid and PV module. This gives rise to the flow of leakage current which is disastrous for the system when it exceeds a specific value. Thus, minimization of this leakage current after the removal of the transformer has been an interesting topic explored by many researchers. Many topologies have been proposed targeting reduction in this leakage current either by 1.) Directly connecting the PV negative with neutral of utility grid or 2.) Disconnecting the PV panel side from AC side. This generally involved addition of more switches or diodes or supplementary branches to disconnect during the freewheeling period. Generally, the above-mentioned ways lead to a reduction in efficiency due to increased losses or complex circuitry. The motivation of this thesis is to design a transformerless inverter for single-phase PV grid-tied system with a smaller number of devices and still has minimum ground current. It discusses the prevailing inverter topologies in detail and then explains the modes of operation of the proposed inverter. A simple control strategy has been derived and passive elements of the inverter are designed. The simulation results presented have validated the theoretical claims. The experimental results which are similar to simulation results are evidence that the proposed topology is suitable for PV grid-tied systems. Also, the dynamic modeling of the inverter has been done to derive the plant transfer function. Then, the Proportional Resonant (PR) controller has been designed to ensure the flow of sinusoidal current into the grid with zero steady-state error and constant sinusoidal grid voltage irrespective of load change. The simulation and experimental results achieved high performance which makes this topology successful and promising for grid-tied PV systems

Transformerless Inverter Topologies for Single-Phase Photovoltaic Systems:A Comparative Review

In photovoltaic (PV) applications, a transformer is often used to provide galvanic isolation and voltage ratio transformations between input and output. However, these conventional iron-and copper-based transformers increase the weight/size and cost of the inverter while reducing the efficiency and power density. It is therefore desirable to avoid using transformers in the inverter. However, additional care must be taken to avoid safety hazards such as ground fault currents and leakage currents, e.g., via the parasitic capacitor between the PV panel and ground. Consequently, the grid connected transformerless PV inverters must comply with strict safety standards such as IEEE 1547.1, VDE0126-1-1, EN 50106, IEC61727, and AS/N ZS 5033. Various transformerless inverters have been proposed recently to eliminate the leakage current using different techniques such as decoupling the dc from the ac side and/or clamping the common mode (CM) voltage (CMV) during the freewheeling period, or using common ground configurations. The permutations and combinations of various decoupling techniques with integrated voltage buck-boost for maximum power point tracking (MPPT) allow numerous new topologies and configurations which are often confusing and difficult to follow when seeking to select the right topology. Therefore, to present a clear picture on the development of transformerless inverters for the next-generation grid-connected PV systems, this paper aims to comprehensively review and classify various transformerless inverters with detailed analytical comparisons. To reinforce the findings and comparisons as well as to give more insight on the CM characteristics and leakage current, computer simulations of major transformerless inverter topologies have been performed in PLECS software. Moreover, the cost and size are analyzed properly and summarized in a table. Finally, efficiency and thermal analysis are provided with a general summary as well as a technology roadmap.</p

Development Of Multistage Cuk Converter For Pv Voltage Regulation.

Tesis ini mengemukakan reka bentuk pengubah SPMS untuk aplikasi berkuasa rendah.Litar penukar adalah berdasarkan topologi CUK yang secara asasnya ialah kombinasi topologi penukar “buck” dan “boost”. This thesis presents the design of a transformerless SMPS for low power applications. The converter circuit is based on CUK topology which is basically a combination of buck and boost converter topologies

Hybrid Transformerless PV Converters with Low Leakage Currents:Analysis and Configuration

Abstract This paper proposes a hybrid transformerless photovoltaic (PV) converter with simultaneous AC and DC outputs. It is specifically suitable for residential PV systems due to its high efficiency, versatility and flexibility, while maintaining lower leakage currents. The proposed converter is configured by replacing the control switch of the boost converter with a transformerless voltage‐source inverter (VSI), enabling multiple outputs. In addition, a symmetrical boost inductor is adopted to clamp the common‐mode voltage as a constant, resulting in low leakage currents. To illustrate the configuration principle, a hybrid converter with a highly efficient and reliable inverter concept (HERIC) as the VSI is exemplified. Besides, the dedicated modulation scheme for the proposed converter is detailed to achieve low leakage currents, reactive power injection and high efficiency. Furthermore, as the shoot‐through state of inverter legs is allowable for the proposed converter, i.e. no need to add dead time, the reliability and power quality of the proposed converter can be improved. Simulations and experimental tests are performed on an example hybrid converter (with an HERIC as the VSI) to validate the analysis

Design and implementation of a dual-input single-output photovoltaic converter

In many solar inverters, a dc/dc converter is mainly located between the solar arrays and the inverter. This study presents an enhanced maximum power point tracking (MPPT) algorithm for photovoltaic (PV) systems that drives solar array voltages to track a reference value and decreases fluctuations and oscillations in PV voltage. Different from the previously presented methods, a novel MPPT method is proposed that ensures tracking accuracy by considering output voltage in addition to input voltage and currents. The proposed method detects dI/dV variations, compares the output voltage with the desired reference to shift operation mode and refreshes step size. The digital filtering, enhanced PI, and perturb-and-observe (P&O) tracking features of the proposed MPPT method make it robust to mitigate source fluctuations and sensitivity to partial shading based oscillations. In order to validate the success of the proposed method, a test rig has been installed with dual boost converters. The performance improvements have been verified by both simulation and experimental results that are compared to InCon and P&O MPPT methods. It is also confirmed by experimental results that the proposed MPPT method provides robust control capability in terms of tracking the reference voltage and rejecting the effects of various shading situations on solar arrays