Optical fiber transmission systems for in-door next generation broadband access network.

This thesis was submitted for the award of Doctor of Philosophy and was awarded by Brunel University London.This thesis investigates the generation and radio-over-fibre (RoF) transport of unlicensed 60 GHz millimetre-wave (mm-wave) frequency band. The investigated benefits of transmission schemes applicable for the mm-wave generation include optical carrier suppression (OCS), optical frequency multiplication (OFM) and remote heterodyne detection (RHD). For the in-door cabling of the mm-wave transmission, a low-cost polymer optical fibre (POF) along with bend-insensitive single mode fibre (BI-SMF) has been investigated for short-range networks. Transporting mm-wave generated signals over POF and BI-SMF cables based on OCS scheme showed results with the highest spectral efficiency and least inter-symbol interference over a 2.5 Gbit/s data delivery. Based on this thesis analysis, OCS simulation of POF showed the most reliable power penalty performance and receiver sensitivity at 30-m whilst the BI-SMF fiber produced equal observations at 150-m and more. In observing the free space links of delivering the RoF signal, the attenuation on the received signal power for both POF and BI-SMF was insignificant but expected, as the simulation assumed complete and total collimation of the light beams onto the aperture of the photodetector. OCS scheme for mm-wave generation and transport was explored based on the cost effectiveness of using one external modulator compared to other generation schemes that utilised more than one external modulator. OFM scheme was simulated to transport LTE and Wi-Fi signals along with 60 GHz RF band through both SMF and MMF-POF/BI-SMF cables. OFM transport scheme produced the highest attenuation on LTE, Wi-Fi and mm-wave signals carrying 100 Mbit/s data as simulated POF lengths increased. The best performance POF length was observed at 10-m. The application of offset launch technique at the coupling of SMF and POF showed insignificant improvement on signal bandwidth. The free space OFM transmission also demonstrated negligible change to the received signal power. This reinforces the attributes of deploying OWC system in an in-door environment. In other investigation, the simulated successful delivery of mm-wave signal using RHD scheme modulated and transported 10 Gbit/s data signal over POF and BI-SMF cables. Additional observed unrecorded result also showed BI-SMF cable maintained a 2% reduction of received power for 450-m fiber cable from 150-m. The attributes to RHD includes its low operating power system application and delivery of localised 60 GHz signal for uplink RoF transmission. The conceptualised design of Gigabit data delivery for indoor customer applications either through POF or BI-SMF cable, transporting various wireless channels has been presented in this thesis for the design of a robust next generation Broadband access network to reinforce the fiber-inside-the-home (FiTH) deployment

Radio-over-fibre technologies arising from the Building the future Optical Network in Europe (BONE) project

[EN] This study describes a wide range of salient radio-over-fibre system issues. Impulse radio and multiband ultra-wideband signal distribution over both single-mode fibre and multi-mode fibre (MMF) implementations are considered. Carrier frequencies ranging from 3.1 to 10.6 GHz, up to 60 GHz, are featured, and the use of microring laser transmitters is discussed. A cost-performance comparative analysis of competing distributed antenna system topologies is presented, and a theoretical approach to understanding the factors underlying radio-over-MMF performance for within-building applications is discussed. Finally, techniques to minimise thermal impacts on performance are described and novel energy-efficient schemes are introduced. Overall, this study provides a snap-shot of research being undertaken by European institutes involved in the Building the future Optical Network in Europe (BONE) project.The work described in this paper was carried out with the support of the EU-FP7 Network of Excellence BONE project.Parker, M.; Walker, SD.; Llorente, R.; Morant, M.; Beltrán, M.; Möllers, I.; Jäger, D.... (2010). Radio-over-fibre technologies arising from the Building the future Optical Network in Europe (BONE) project. IET Optoelectronics. 4(6):247-259. https://doi.org/10.1049/iet-opt.2009.0062S24725946http://www.ftthcouncil.euGomes, N. J., Morant, M., Alphones, A., Cabon, B., Mitchell, J. E., Lethien, C., … Iezekiel, S. (2009). Radio-over-fiber transport for the support of wireless broadband services [Invited]. Journal of Optical Networking, 8(2), 156. doi:10.1364/jon.8.000156Thakur, M. P., Quinlan, T. J., Bock, C., Walker, S. D., Toycan, M., Dudley, S. E. M., … Ben-Ezra, Y. (2009). 480-Mbps, Bi-Directional, Ultra-Wideband Radio-Over-Fiber Transmission Using a 1308/1564-nm Reflective Electro-Absorption Transducer and Commercially Available VCSELs. Journal of Lightwave Technology, 27(3), 266-272. doi:10.1109/jlt.2008.2005644ECMA-368 International Standard: ‘High rate ultra wideband PHY and MAC standard’, December 2008FCC 02-48: ‘Revision of part 15 of the commission's rules regarding ultra-wideband transmission systems’, April 2002ECC∕DEC∕(06)04: ‘On the harmonised conditions for devices using ultra-wideband (UWB) technology in bands below 10.6 GHz’, March 2006ETSI EN 302 065 V1.1.1 (2008-02): ‘Electromagnetic compatibility and radio spectrum matters (ERM); ultra wideband (UWB) technologies for communication purposes; harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive’, February 2008WiMedia Alliance: Worldwide regulatory status [online]. Available at: http://www.wimedia.orgMikroulis, S., Simos, H., Roditi, E., & Syvridis, D. (2005). Ultrafast all-optical AND logic operation based on four-wave mixing in a passive InGaAsP-InP microring resonator. IEEE Photonics Technology Letters, 17(9), 1878-1880. doi:10.1109/lpt.2005.853260Argyris, A., Hamacher, M., Chlouverakis, K. E., Bogris, A., & Syvridis, D. (2008). Photonic Integrated Device for Chaos Applications in Communications. Physical Review Letters, 100(19). doi:10.1103/physrevlett.100.194101Win, M. Z., & Scholtz, R. A. (1998). On the robustness of ultra-wide bandwidth signals in dense multipath environments. IEEE Communications Letters, 2(2), 51-53. doi:10.1109/4234.660801Flatman, A.: In-premises optical fibre installed base analysis to 2007. Presented at the IEEE 802.3 10GbE over FDDI Grade Fibre Study Group, Orlando, FL, March 2004Raddatz, L., & White, I. H. (1999). Overcoming the modal bandwidth limitation of multimode fiber by using passband modulation. IEEE Photonics Technology Letters, 11(2), 266-268. doi:10.1109/68.740725Hartmann, P., Xin Qian, Wonfor, A., Penty, R. V., & White, I. H. (2005). 1-20 GHz Directly Modulated Radio over MMF Link. 2005 International Topical Meeting on Microwave Photonics. doi:10.1109/mwp.2005.203548Kanprachar, S., & Jacobs, I. (2003). Diversity coding for subcarrier multiplexing on multimode fibers. IEEE Transactions on Communications, 51(9), 1546-1553. doi:10.1109/tcomm.2003.816981Gasulla, I., & Capmany, J. (2006). Transfer function of multimode fiber links using an electric field propagation model: Application to Radio over Fibre Systems. Optics Express, 14(20), 9051. doi:10.1364/oe.14.009051Al-Raweshidy, H., and Komaki, S.: ‘Radio over fiber technologies for mobile communication networks’, (Artech House 2002)Sauer, M., Kobyakov, A., & George, J. (2007). Radio Over Fiber for Picocellular Network Architectures. Journal of Lightwave Technology, 25(11), 3301-3320. doi:10.1109/jlt.2007.906822Gomes, N. J., Nkansah, A., & Wake, D. (2008). Radio-Over-MMF Techniques—Part I: RF to Microwave Frequency Systems. Journal of Lightwave Technology, 26(15), 2388-2395. doi:10.1109/jlt.2008.925624Rajan, G., Semenova, Y., Pengfei Wang, & Farrell, G. (2009). Temperature-Induced Instabilities in Macro-Bend Fiber Based Wavelength Measurement Systems. Journal of Lightwave Technology, 27(10), 1355-1361. doi:10.1109/jlt.2009.2014081Montalvo, J., Vázquez, C., & Montero, D. S. (2006). CWDM self-referencing sensor network based on ring resonators in reflective configuration. Optics Express, 14(11), 4601. doi:10.1364/oe.14.00460

Impulse radio ultra wideband over fiber techniques for broadband in-building network applications

In recent years, the demand for high bandwidth and mobility from the end users has been continuously growing. To satisfy this demand, broadband communication technologies that combined the benefit of both wired and wireless are considered as vital solutions. These hybrid optical wireless solutions enable multi-Gbit/s transmission as well as adequate flexibility in terms of mobility. Optical fiber is the ideal medium for such hybrid solution due its signal transparency and wide bandwidth. On the other hand, ultra wideband(UWB) radio over optical fiber technology is considered to be one of the key promising technologies for broadband communication and sensor network applications. The growing interest for UWB is mainly due to its numerous attractive features, such as low power spectral density, tolerance to multipath fading, low probability of interception, coexistence with other wireless services and capability of providing cost-effective > 1 Gb/s transmission. The main idea of UWB over fiber is to deliver UWB radio signals over optical channels, where the optical part serves as a backbone communication infrastructure to carry the UWB signal with a bandwidth of several GHz. This enables multiple novel applications such as: range extension of high speed wireless personal area networks (WPANs), low cost distributed antenna systems, secure and intelligent networks, or delivering broadband services to remote areas. In particular, this thesis deals with novel concepts on shaping and generation of IR-UWB pulses, theoretical and experimental demonstrations over different fiber types, routing of integrated wired/wireless IR-UWB services and effect of fiber types on ranging/localization of IR-UWB-over-fiber systems. Accordingly, this thesis investigates techniques for delivery of high data rate wireless services using impulse radio ultra wideband (IR-UWB) over fiber technology for both access and in-building network applications. To effectively utilize the emission mask imposed for UWB technologies by the Federal Communications Commission(FCC), novel pulse shaping techniques have been investigated and experimentally demonstrated. Comparison of the proposed pulses with conventional ones in terms of the compliance to the FCC-mask requirements, spectral power efficiencies and wireless coverage has been theoretically studied. Simple and efficient optical generation of the new pulse has been experimentally demonstrated. Furthermore, performance evaluation of 2 Gb/s transmission of IR-UWB over different types of fiber such as 25 km silica single-mode, 4.4 km silica multi-mode and 100 m plastic heavily-multi-mode fiber have been performed. To improve the functionalities of in-building networks for the delivery of wireless services; techniques that provide flexibility in terms of dynamic capacity allocation have been investigated. By employing wavelength conversion based on cross-gain modulation in optical semiconductor amplifiers(SOA), routing of three optical channels of IR-UWB over fiber system has been experimentally realized. To reduce the cost of the overall system and share the optical infrastructure, an integrated testbed for wired baseband data and wireless IR-UWB over 1 km SMF-28 fiber has been developed. Accordingly, 1.25 Gb/s wired baseband and 2 Gb/s wireless IR-UWB data have been successfully transmitted over the testbed. Furthermore, to improve the network flexibility, routing of both wired baseband and wireless signals has been demonstrated. Additionally, the ranging and localization capability of IR-UWB over fiber for in-door wireless picocells have been investigated. The effect of different fiber types (4 km SMF, 4.4 km GI-MMF and 100 m PF GI-POF) on the accuracy of the range estimation using time-of-arrival (ToA) ranging technique has been studied. A high accuracy in terms of cm level was achieved due to the combined effect of high bandwidth IR-UWB pulses, short reach fiber and low chromatic dispersion at 1300nm wavelength. Furthermore, ranging/ localization using IR-UWB over fiber system provides additional benefit of centralizing complex processing algorithms, simplifying radio access points, relaxing synchronization requirement, enabling energy-efficient and efficient traffic management networks. All the concepts, design and system experiments presented in this thesis underline the strong potential of IR-UWB for over optical fiber(silica and plastic) techniques for future smart, capacity and energy-efficient broadband in-building network applications

Dark signalling and code division multiple access in an optical fibre LAN with a bus topology

This thesis describes an optical fibre network that uses a bus topology and Code Division Multiple Access (CDMA). Various potential configurations are analysed and compared and it is shown that a serious limitation of optical CDMA schemes using incoherent correlators is the effect of optical beating due to the presence of multiple incoherent optical signals at the receiver photodiode. The network proposed and analysed in this thesis avoids beating between multiple optical fields because it only uses a single, shared, optical source. It does this through the SLIM (Single Light-source with In-line Modulation) configuration in which there is a continuously-operating light source at the head-end of a folded bus, and modulators at the nodes to impose signals on the optical field in the form of pulses of darkness which propagate along the otherwise continuously bright bus. Optical CDMA can use optical-fibre delay-line correlators as matched filters, and these may be operated either coherently or incoherently.Coherent operation is significantly more complex than incoherent operation, but incoherent correlators introduce further beating even in a SLIM network. A new design of optical delay-line correlator, the hybrid correlator, is therefore proposed, analysed and demonstrated. It is shown to eliminate beating. A model of a complete network predicts that a SLIMbus using optical CDMA with hybrid correlators can be operated at TeraBaud rates with the number of simultaneous users limited by multiple access interference (MAI), determined only by the combinatorics of the code set

Advanced DSP Techniques for High-Capacity and Energy-Efficient Optical Fiber Communications

The rapid proliferation of the Internet has been driving communication networks closer and closer to their limits, while available bandwidth is disappearing due to an ever-increasing network load. Over the past decade, optical fiber communication technology has increased per fiber data rate from 10 Tb/s to exceeding 10 Pb/s. The major explosion came after the maturity of coherent detection and advanced digital signal processing (DSP). DSP has played a critical role in accommodating channel impairments mitigation, enabling advanced modulation formats for spectral efficiency transmission and realizing flexible bandwidth. This book aims to explore novel, advanced DSP techniques to enable multi-Tb/s/channel optical transmission to address pressing bandwidth and power-efficiency demands. It provides state-of-the-art advances and future perspectives of DSP as well