Design techniques for wideband low-power Delta-Sigma analog-to-digital converters

Delta-Sigma (ΔΣ) analog-to-digital converters (ADCs) are traditionally used in high quality audio systems, instrumentation and measurement (I&M) and biomedical devices. With the continued downscaling of CMOS technology, they are becoming popular in wideband applications such as wireless and wired communication systems,high-definition television and radar systems. There are two general realizations of a ΔΣ modulator. One is based on the discrete-time (DT) switched-capacitor (SC) circuitry and the other employs continuous-time (CT) circuitry. Compared to a CT structure, the DT ΔΣ ADC is easier to analyze and design, is more robust to process variations and jitter noise, and is more flexible in the multi-mode applications. On the other hand, the CT ΔΣ ADC does not suffer from the strict settling accuracy requirement for the loop filter and thus can achieve lower power dissipation and higher sampling frequency than its DT counterpart. In this thesis, both DT and CT ΔΣ ADCs are investigated. Several design innovations, in both system-level and circuit-level, are proposed to achieve lower power consumption and wider signal bandwidth. For DT ΔΣ ADCs, a new dynamic-biasing scheme is proposed to reduce opamp bias current and the associated signal-dependent harmonic distortion is minimized by using the low-distortion architecture. The technique was verified in a 2.5MHz BW and 13bit dynamic range DT ΔΣ ADC. In addition, a second-order noise coupling technique is presented to save two integrators for the loop filter, and to achieve low power dissipation. Also, a direct-charge-transfer (DCT) technique is suggested to reduce the speed requirements of the adder, which is also preferable in wideband low-power applications. For CT ΔΣ ADCs, a wideband low power CT 2-2 MASH has been designed. High linearity performance was achieved by using a modified low-distortion technique, and the modulator achieves higher noise-shaping ability than the single stage structure due to the inter-stage gain. Also, the quantization noise leakage due to analog circuit non-idealities can be adaptively compensated by a designed digital calibration filter. Using a 90nm process, simulation of the modulator predicts a 12bit resolution within 20MHz BW and consumes only 25mW for analog circuitry. In addition, the noise-coupling technique is investigated and proposed for the design of CT ΔΣ ADCs and it is promising to achieve low power dissipation for wideband applications. Finally, the application of noise-coupling technique is extended and introduced to high-accuracy incremental data converters. Low power dissipation can be expected

Low power design techniques for high speed pipelined ADCs

Real world is analog but the processing of signals can best be done in digital domain. So the need for Analog to Digital Converters(ADCs) is ever rising as more and more applications set in. With the advent of mobile technology, power in electronic equipment is being driven down to get more battery life. Because of their ubiquitous nature, ADCs are prime blocks in the signal chain in which power is intended to be reduced. In this thesis, four techniques to reduce power in high speed pipelined ADCs have been proposed. The first is a capacitor and opamp sharing technique that reduces the load on the first stage opamp by three fold. The second is a capacitor reset technique that aids removing the sample and hold block to reduce power. The third is a modified MDAC which can take rail-to-rail input swing to get an extra bit thus getting rid of a power hungry opamp. The fourth is a hybrid architecture which makes use of an asynchronous SAR ADC as the backend of a pipelined ADC to save power. Measurement and simulation results that prove the efficiency of the proposed techniques are presented

High performance continuous-time filters for information transfer systems

Vast attention has been paid to active continuous-time filters over the years. Thus as the cheap, readily available integrated circuit OpAmps replaced their discrete circuit versions, it became feasible to consider active-RC filter circuits using large numbers of OpAmps. Similarly the development of integrated operational transconductance amplifier (OTA) led to new filter configurations. This gave rise to OTA-C filters, using only active devices and capacitors, making it more suitable for integration. The demands on filter circuits have become ever more stringent as the world of electronics and communications has advanced. In addition, the continuing increase in the operating frequencies of modern circuits and systems increases the need for active filters that can perform at these higher frequencies; an area where the LC active filter emerges. What mainly limits the performance of an analog circuit are the non-idealities of the used building blocks and the circuit architecture. This research concentrates on the design issues of high frequency continuous-time integrated filters. Several novel circuit building blocks are introduced. A novel pseudo-differential fully balanced fully symmetric CMOS OTA architecture with inherent common-mode detection is proposed. Through judicious arrangement, the common-mode feedback circuit can be economically implemented. On the level of system architectures, a novel filter low-voltage 4th order RF bandpass filter structure based on emulation of two magnetically coupled resonators is presented. A unique feature of the proposed architecture is using electric coupling to emulate the effect of the coupled-inductors, thus providing bandwidth tuning with small passband ripple. As part of a direct conversion dual-mode 802.11b/Bluetooth receiver, a BiCMOS 5th order low-pass channel selection filter is designed. The filter operated from a single 2.5V supply and achieves a 76dB of out-of-band SFDR. A digital automatic tuning system is also implemented to account for process and temperature variations. As part of a Bluetooth transmitter, a low-power quadrature direct digital frequency synthesizer (DDFS) is presented. Piecewise linear approximation is used to avoid using a ROM look-up table to store the sine values in a conventional DDFS. Significant saving in power consumption, due to the elimination of the ROM, renders the design more suitable for portable wireless communication applications

Accuracy enhancement techniques in low-voltage high-speed pipelined ADC design

Pipelined analog to digital converters (ADCs) are very important building blocks in many electronic systems such as high quality video systems, high performance digital communication systems and high speed data acquisition systems. The rapid development of these applications is driving the design of pipeline ADCs towards higher speed, higher dynamic range, lower power consumption and lower power supply voltage with the CMOS technology scaling. This trend poses great challenges to conventional pipelined ADC designs which rely on high-gain operational amplifiers (opamps) and well matched capacitors to achieve high accuracy. In this thesis, two novel accuracy improvement techniques to overcome the accuracy limit set by analog building blocks (opamps and capacitors) in the context of low-voltage and high-speed pipelined ADC design are presented. One is the time-shifted correlated double sampling (CDS) technique which addresses the finite opamp gain effect and the other is the radix-based background digital calibration technique which can take care of both finite opamp gain and capacitor mismatch. These methods are simple, easy to implement and power efficient. The effectiveness of the proposed techniques is demonstrated in simulation as well as in experiment. Two prototype ADCs have been designed and fabricated in 0.18μm CMOS technology as the experimental verification of the proposed techniques. The first ADC is a 1.8V 10-bit pipeline ADC which incorporated the time-shifted CDS technique to boost the effective gain of the amplifiers. Much better gain-bandwidth tradeoff in amplifier design is achieved with this gain boosting. Measurement results show total power consumption of 67mW at 1.8V when operating at 100MSPS. The SNR, SNDR and SFDR are 55dB, 54dB and 65dB respectively given a 1MHz input signal. The second one is a 0.9V 12-bit two-stage cyclic ADC which employed a novel correlation-based background calibration to enhance the linearity. The linearity limit set by the capacitor mismatches, finite opamp gain effects is exceeded. After calibration, the SFDR is improved by about 33dB and exceeds 80dB. The power consumption is 12mW from 0.9V supply when operating at 2MSPS

Wideband discrete-time delta-sigma analog-to-digital converters with shifted loop delays

Low-distortion architecture is widely used in wideband discrete-time switched-capacitor delta-sigma ADC design. However, it suffers from the power-hungry active adder and critical timing for quantization and dynamic element matching (DEM). To solve this problem, this dissertation presents a delta-sigma modulator architecture with shifted loop delays. In this project, shifted loop delays (SLD) technique can relax the speed requirements of the quantizer and the dynamic element matching (DEM) block, and eliminate the active adder. An implemented 0.18 um CMOS prototype with the proposed architecture provided 81.6 dB SNDR, 81.8 dB dynamic range, and -95.6 dB THD in a signal bandwidth of 4 MHz. It dissipates 19.2 mW with a 1.6 V power supply. The conventional low-distortion ADC was also implemented on the same chip for comparison. The new circuit has superior performance, and dissipates 25% less power (19.2 mW vs. 24.9 mW) than the conventional one. The figure-of-merit for the ADC with SLD is among the best reported for wideband discrete-time ADCs, and is almost 40% better than that of the conventional ADC. The second project describes two techniques to enhance the noise shaping function in the proposed low-distortion ΔΣ modulator with shifted loop delays. One is self-noise coupling based on low-distortion ΔΣ structure; the other is noise-coupled time-interleaved ΔΣ modulator. Both architectures use shifted loop delays to relax the critical timing constraints in the modulator feedback path, then to save power consumption of each block in the modulators. Two ΔΣ ADCs were analyzed and simulated in a 0.18um CMOS technology. The simulation results highly verify the effectiveness of the proposed structure. The third system describes the design technique for double-sampled wideband ΔΣ ADCs with shifted loop delays (SLD). The added loop delay in the feedback branch relaxes the critical timing for DEM logic. Delay shifting can be combined with such useful techniques as low-distortion circuitry and noise coupling for wideband ΔΣ modulators. The presented techniques relax the timing for inherent quantization delay, reduce the speed requirements for the critical circuit blocks, and achieve power efficiency by replacing the power-hungry blocks normally used in the modulators. Analysis of all architectures allows the choice of the most power-efficient topology for a wideband ΔΣ modulator. The proposed second-order and third-order ΔΣ modulators were designed and simulated to verify the effectiveness of the shifted loop delays techniques.Keywords: Noise-shaping, Shifted Loop Delays, Delta-Sigma Modulator, Low-distortion, AD

Low-power double-sampled delta-sigma modulator for broadband applications

High speed and high resolution analog-to-digital converter is a key building block for broadband wireless communications, high definition video applications, medical images and so on. By leveraging the down scaling of the latest CMOS technology and the noise shaping properties, delta-sigma (ΔΣ) ADCs are able to achieve wide-band operation and high accuracy simultaneously. At first in this thesis, two novel techniques which can be applied to high performance ΔΣ ADC design are proposed. The first one is a modulator architectural innovation that is able to effectively solve the feedback timing constraints in a double-sampled ΔΣ modulator. The second one is a transistor level improvement to reduce the hardware consumption in a standard Date Weighted Averaging (DWA) realization. Next, charge-pump (CP) based switched-capacitor (SC) integrator is discussed. A cross-coupling technique is proposed to eliminate parasitic capacitor effect in a CP based SC integrator. Also design methodologies are introduced to incorporate a modified CP based SC integrator into a low-distortion ΔΣ modulator. A second-order ΔΣ modulator was designed and simulated to verify the proposed modulator topology. Finally, design of a double-sampled broadband 12-bit ΔΣ modulator is presented. To achieve very low power consumption, this modulator utilizes the following two key design techniques: 1. Double sampled integrator to increase the effective over-sampling ratio. 2. Capacitor reset technique allows the use of only one feedback DAC at the front end of the modulator to completely eliminate the quantization noise folding back. A 2+2 cascaded topology with 3-bit internal quantizer is used in this ΔΣ modulator to adequately suppress the quantization noise while guarantee the loop stability. This ΔΣ modulator was fabricated in a 90nm digital CMOS process and achieves an SNDR of 70dB within a 5MHz signal bandwidth. The modulator occupies a silicon area of 0.5mm² and consumes 10mW with a supply voltage of 1.2V

High efficiency delta-sigma modulation data converters

Enabled by continued device scaling in CMOS technology, more and more functions that were previously realized in separate chips are getting integrated on a single chip nowadays. Integration on silicon has opened the door to new portable wireless applications, and initiated a widespread use of these devices in our common everyday life. Wide signal bandwidth, high linearity and dynamic range, and low power dissipation are required of embedded data converters that are the performance-limiting key building blocks of those systems. Thus, power-efficient and highly-linear data conversion over wide range of signal bands is essential to get the full benefits from device scaling. This continued trend keeps innovation in the design of data converter continuing. Traditionally, delta-sigma modulation data converters proved to be very effective in applications where high resolution was necessary in a relatively narrow signal band. There have been active research efforts across academia and industry on the extension of achievable signal bandwidth without compromising the performance of these data converters. In this dissertation, architectural innovations, combined with effective design techniques for delta-sigma modulation data converters, are presented to overcome the associated limitations. The effectiveness of the proposed approaches is demonstrated by test results for the following state-of-the-art prototype designs: (1) a 0.8 V, 2.6 mW, 88 dB dual-channel audio delta-sigma modulation D/A converter with headphone driver; (2) an 88 dB ring-coupled delta-sigma ADC with 1.9 MHz bandwidth and -102.4 dB THD; (3) a multi-cell noise-coupled delta-sigma ADC with 1.9 MHz bandwidth, 88 dB DR, and -98 dB THD; (4) an 8.1 mW, 82 dB self-coupled delta-sigma ADC with 1.9 MHz bandwidth and -97 dB THD; (5) a noise-coupled time-interleaved delta-sigma ADC with 4.2 MHz bandwidth, -98 dB THD, and 79 dB SNDR; (6) a noise-coupled time-interleaved delta-sigma ADC with 2.5 MHz bandwidth, -104 dB THD, and 81 dB SNDR. As an extension of this research, two novel architectures for efficient double-sampling delta-sigma ADCs and improved low-distortion delta-sigma ADC are proposed, and validated by extensive simulations.Keywords: improved low-distortion modulator, time interleaving, data converter, multi-cell ADC, efficient double sampling, noise coupling, delta-sigma modulatio

Pixel and Readout Circuit of a Wide Dynamic Range Linear-Logarithmic Current-Mode Image Sensor

RESUME Le capteur d’images est la partie principale de tout système d’acquisition d’images, quelle que soit son application. Jusqu’à la fin des années 1990, les capteurs de type CCD ont dominé le marché en raison de leur qualité d’image exceptionnelle. À l’opposé des capteurs CCD, les capteurs CMOS offrent des possibilités intéressantes d’intégrer les circuits de traitement de signal sur un même substrat en vue d’obtenir une caméra sur puce. Entant que ces capteurs opèrent avec des tensions d’alimentations plus faibles que celles requise par les capteurs CCD, elles possèdent une faible consommation de puissance. De plus, les coûts associés à la fabrication des capteurs CMOS sont plus faibles que ceux engendrés par les capteurs CCD. Ces caractéristiques font en sorte que les capteurs d’images CMOS se prêtent à un plus grand nombre d’application que leurs équivalents CCD. Dans ce projet, l’objectif principal est de concevoir un capteur d’images ayant une plage dynamique élevée. Il possède l’avantage de deux modes d’opération, linéaire et logarithmique, ainsi qu’une lecture en mode courant afin d’augmenter sa plage dynamique. Les tensions d’alimentation des technologies CMOS diminue de plus en plus, et de ce fait la plage dynamique du pixel. En fonctionnant en mode courant, on arrive à atténuer cet effet. Le projet consiste à concevoir des circuits : convoyeur de courant, ‘delta-reset-sampling’ et un comparateur de courant qui sont efficaces pour les modes d’opération linéaire et logarithmique du pixel et permettent de détecter dans quels des deux modes se situe le pixel de façon à réaliser, à l’étage subséquent, une conversion analogique-numérique adéquate. Le pixel à trois transistors fonctionnant en mode courant utilise un transistor PMOS dans la région linéaire pour la lecture et un transistor PMOS de reset qui permet une réponse linéaire-logarithmique combinée. L'une des contributions à la non-linéarité de la réponse provient de l'effet provoqué par la résistance ‘on’ du transistor ‘select’. Pour éliminer cet effet, nous appliquons une fonction de linéarisation qui est effectuée dans le domaine numérique. Le mode d’opération du pixel est déterminé dans le circuit de lecture de colonne et un signal est envoyé à l'unité de traitement numérique comme indicateur de mode. Un prototype a été conçu et fabriqué en CMOS 0.35µm standard, 3.3V. Les résultats expérimentaux sont concluants et montrent une plage dynamique intrascènede 100 dB.----------ABSTRACT Digital cameras are rapidly becoming a dominant image capture devices. They are enabling many new applications. Charge-coupled devices (CCDs) have been the basis for solid state imaging since the 1970s. However, during the last decade, interest in CMOS imagers has increased significantly since they are capable of offering System-on-Chip (SoC) functionality. This can greatly reduce camera cost, power consumption, and size. Furthermore, by integrating innovative circuits on the same chip, the performance of CMOS image sensors could be extended beyond the capabilities of CCDs. Dynamic range is an important performance criterion for all image sensors. This thesis presents a current-mode CMOS image sensor operating in linear-logarithmic response. The objective of this design is to improve the dynamic range of the image sensor, and to provide a method for mode detection of the image sensor response. One of the motivations of using current-mode has been the shrinking feature size of CMOS devices. This leads to the reduction of supply voltage which causes the degradation of circuit performance in term of dynamic range. Such problem can be alleviated by operating in current-mode. The column readout circuits are designed in current-mode in order to be compatible with the image sensor. The readout circuit is composed of a first-generation current conveyor, an improved current memory is employed as a delta reset sampling unit, a differential amplifier as an integrator and a dynamic comparator. The current-mode three-transistor active pixel sensor uses a PMOS readout transistor in the linear region of operation and a PMOS reset transistor that allows for a linear-logarithmic response. One of the non-linearity contributions is the effect caused by the ‘on’ resistance of the select transistor. To eliminate this effect, we apply a linearization function that can be performed in the digital domain. The pixel response operation is determined in the column readout circuit and a signal is sent to the digital processing unit as an indicator. These circuits were implemented using a standard CMOS technology with no process modification. A prototype has been designed and fabricated in a standard AMS 2P4M, 3.3V, CMOS 0.35μm process from Austrian Microsystem

Novel structures for high-speed delta-sigma data converters

As CMOS processes keep scaling down devices, the maximum operating frequencies of CMOS devices increase, and hence circuits can process very wide band signals. Moreover, the small physical dimensions of transistors allow the placing of many more blocks into a single chip, including highly accurate analog blocks and complicated digital blocks, which can process audio to communication data. Nowadays, wideband and low-power data converter is mandatory for mobile applications which need a bridge between analog and digital blocks. In this dissertation, low-power and wideband techniques are proposed. An embedded-adder quantizer with dynamic preamplifier is proposed to achieve power-efficient operation. Various double-sampling schemes are studied, and novel schemes are presented to achieve wideband operation without noise folding effect. To reduce timing delay and idle tones, a high speed DEM which alternates two sets of comparator references is proposed. Multi-cell architecture is studied to insure higher performance when the number of modulators increases. 0.18 um double-poly/4-metal CMOS process was used to implement a prototype IC. 20 MHz signal bandwidth was achieved with a 320 MHz sampling clock. The peak SNDR was 63 dB. The figure-of-merit FoM = P/(2*BW*2[superscript ENOB]) was 0.35 pJ/conversion, with a 16 mW power consumption. Measurement results show that the proposed design ideas are useful for low-power and wideband delta-sigma modulators which have low OSR. A second-order noise-coupled modulator with an embedded-zero optimization was proposed to reduce power consumption by eliminating some of the integrators. This architecture makes easier the implementation of the small feedback capacitors for high OSR modulators