Improved Non-Isolated Bidirectional DC-DC Converter Assisted with an Active Resonant Network

OP VVV Electrical Engineering Technologies with High-Level of Embedded Intelligence CZ.02.1.01/0.0/0.0/18_069/0009855 and project No. SGS-2021-021This paper proposes a new non-isolated bidirectional dc-dc converter (NI-BDC) with an auxiliary resonant network (ARN) that is typically operated in both boost and buck modes. Regardless the direction of power flow, soft-switching capabilities such as zero voltage switching (ZVS) and zero current switching (ZCS) conditions has been obtained under light and heavy loads. This converter avoids the need of coupled inductors as against conventional converters thus reducing the size of the converter and minimizes the device count. The auxiliary resonant network mainly consisting of resonant inductor, capacitor, auxiliary switch and a diode. Furthermore, the zero voltage switching and zero current switching conditions have been achieved in both boost and buck modes that reduces reverse recovery conduction period of the body diodes of all the power switches. The proposed converter operates with soft-switching at constant switching frequency giving continuous inductor current. The detailed operating principles for boost and buck modes are described. The theoretical analysis and simulation results are presented

A three-switch high-voltage converter

A novel single active switch two-diodes high-voltage converter is presented. This converter can operate into a capacitor-diode voltage multiplier, which offers simpler structure and control, higher efficiency, reduced electromagnetic interference (EMI), and size and weight savings compared with traditional switched-mode regulated voltage multipliers. Two significant advantages are the continuous input current and easy isolation extension. The new converter is experimentally verified. Both the steady-state and dynamic theoretical models are correlated well with the experimental dat

A unified analysis of PWM converters in discontinuous modes

Three discontinuous operating modes of PWM (pulsewidth modulated) converters are considered: the discontinuous inductor current mode (DICM), the discontinuous capacitor voltage mode (DCVM), and a previously unidentified mode called the discontinuous quasi-resonant mode (DQRM). DC and small-signal AC analyses are applicable to all basic PWM converter topologies. Any particular topology is taken into account via its DC conversion ratio in the continuous conduction mode. The small-signal model is of the same order as the state-space averaged model for the continuous mode, and it offers improved predictions of the low-frequency dynamics of PWM converters in the discontinuous modes. It is shown that converters in discontinuous modes exhibit lossless damping similar to the effect of the current-mode programming

High frequency electronic ballast provides line frequency lamp current

Most electronic ballasts for fluorescent lamps provide a sinusoidal lamp current at the switching frequency. The high-frequency current flowing through the lamp can generate significant radiated noise, which is unacceptable in noise-sensitive applications, such as fluorescent lights in airplanes. Using shielded enclosures for the lamps may solve the problem, but it is expensive. A discontinuous conduction mode (DCM) electronic ballast topology is presented which drives the lamp with line frequency current, just like a magnetic ballast. However, compared to a magnetic ballast, its weight is substantially reduced due to operation at 40 kHz switching frequency. The topology also ensures unity power factor at the input and stable lamp operation at the output

ASDTIC control and standardized interface circuits applied to buck, parallel and buck-boost dc to dc power converters

Versatile standardized pulse modulation nondissipatively regulated control signal processing circuits were applied to three most commonly used dc to dc power converter configurations: (1) the series switching buck-regulator, (2) the pulse modulated parallel inverter, and (3) the buck-boost converter. The unique control concept and the commonality of control functions for all switching regulators have resulted in improved static and dynamic performance and control circuit standardization. New power-circuit technology was also applied to enhance reliability and to achieve optimum weight and efficiency

Fully equipped half bridge building block for fast prototyping of switching power converters

P

An Integral Battery Charger with Power Factor Correction for Electric Scooter

This paper presents an integral battery charger for an electric scooter with high voltage batteries and interior-permanent-magnet motor traction drive. The battery charger is derived from the power hardware of the scooter, with the ac motor drive that operates as three-phase boost rectifier with power factor correction capability. The control of the charger is also integrated into the scooter control firmware that is implemented on a fixed-point DSP controller. Current-controlled or voltage-controlled charge modes are actuated according to the requirements of the battery management system, that is embedded into the battery pack. With respect to previous integrated chargers, the ac current is absorbed at unitary power factor with no harmonic distortion. Moreover, no additional filtering is needed since the pulsewidth modulation ripple is minimized by means of phase interleaving. The feasibility of the integral charger with different ac motors (induction motor, surface-mounted phase modulation motor) is also discussed, by means of a general model purposely developed for three-phase ac machines. The effectiveness of the proposed battery charger is experimentally demonstrated on a prototype electric scooter, equipped with two Li-ion battery packs rated 260 V, 20 A

Modeling and Analysis of Power Processing Systems (MAPPS). Volume 1: Technical report

Computer aided design and analysis techniques were applied to power processing equipment. Topics covered include: (1) discrete time domain analysis of switching regulators for performance analysis; (2) design optimization of power converters using augmented Lagrangian penalty function technique; (3) investigation of current-injected multiloop controlled switching regulators; and (4) application of optimization for Navy VSTOL energy power system. The generation of the mathematical models and the development and application of computer aided design techniques to solve the different mathematical models are discussed. Recommendations are made for future work that would enhance the application of the computer aided design techniques for power processing systems