21,277 research outputs found
A new approach to applying discrete sliding mode control to 2D systems
Sliding mode control has been applied previously to a specific form of 2D systems (Roesser model). In this paper a new approach (ID vectorial form) is introduced for this problem. Using ID form to represent 2D systems can be used as an alternative strategy to reduce the inherent complexity of 2D systems and their applications. Unlike Wave Advanced Model (WAM) form (proposed by Porter and Aravena), the suggested ID vectorial form, in this paper, has invariable dimension and consequently can be converted to regular form for sliding mode control (SMC). In this paper, the first Fornasini and Marchesini (FM) model of 2D systems which is a second order recursive form is considered. Meantime, the suggested method can be simply deployed to other first or second order 2D models. ©2013 IEEE
Discrete-time output feedback sliding-mode control design for uncertain systems using linear matrix inequalities
An output feedback-based sliding-mode control design methodology for discrete-time systems is considered in this article. In previous work, it has been shown that by identifying a minimal set of current and past outputs, an augmented system can be obtained which permits the design of a sliding surface based upon output information only, if the invariant zeros of this augmented system are stable. In this work, a procedure for realising discrete-time controllers via a particular set of extended outputs is presented for non-square systems with uncertainties. This method is applicable when unstable invariant zeros are present in the original system. The conditions for existence of a sliding manifold guaranteeing a stable sliding motion are given. A procedure to obtain a Lyapunov matrix, which simultaneously satisfies both a Riccati inequality and a structural constraint, is used to formulate the corresponding control to solve the reachability problem. A numerical method using linear matrix inequalities is suggested to obtain the Lyapunov matrix. Finally, the design approach given in this article is applied to an aircraft problem and the use of the method as a reconfigurable control strategy in the presence of sensor failure is demonstrated
Stiffness pathologies in discrete granular systems: bifurcation, neutral equilibrium, and instability in the presence of kinematic constraints
The paper develops the stiffness relationship between the movements and
forces among a system of discrete interacting grains. The approach is similar
to that used in structural analysis, but the stiffness matrix of granular
material is inherently non-symmetric because of the geometrics of particle
interactions and of the frictional behavior of the contacts. Internal geometric
constraints are imposed by the particles' shapes, in particular, by the surface
curvatures of the particles at their points of contact. Moreover, the stiffness
relationship is incrementally non-linear, and even small assemblies require the
analysis of multiple stiffness branches, with each branch region being a
pointed convex cone in displacement-space. These aspects of the particle-level
stiffness relationship gives rise to three types of micro-scale failure:
neutral equilibrium, bifurcation and path instability, and instability of
equilibrium. These three pathologies are defined in the context of four types
of displacement constraints, which can be readily analyzed with certain
generalized inverses. That is, instability and non-uniqueness are investigated
in the presence of kinematic constraints. Bifurcation paths can be either
stable or unstable, as determined with the Hill-Bazant-Petryk criterion.
Examples of simple granular systems of three, sixteen, and sixty four disks are
analyzed. With each system, multiple contacts were assumed to be at the
friction limit. Even with these small systems, micro-scale failure is expressed
in many different forms, with some systems having hundreds of micro-scale
failure modes. The examples suggest that micro-scale failure is pervasive
within granular materials, with particle arrangements being in a nearly
continual state of instability
The application of Discrete sliding mode control in parabolic PDE dynamics
In this paper, the problem of applying Discrete Sliding Mode Control (DSMC) on spatially finite-dimensional systems arising from discretization of bi-variate Partial Differential Equations (PDEs) describing spatio-temporal systems is studied. To this end, heat transfer PDE is discretized to create 2D discrete dynamics and eventually this 2D spatiotemporal discrete form is represented in 1D vectorial form. In order to study the effect of discrepancy between original PDE dynamics and their discrete schemes, an uncertainty term is also considered for the obtained discrete dynamics. According to the notion of strong stability and, in addition, using scaling matrices (similarity transformation), a new method for considering the stability of discrete-time systems in the presence of general uncertainty term (matched and unmatched) is developed. It is also shown that the proposed method in this paper can be used for the case with spatial constraints on the actuation. Consequently, as special cases, the problem of spatially piece-wise constant, sparse and also boundary control input are studied. © 2013 Engineers Australia
The role of different sliding resistances in limit analysis of hemispherical masonry domes
A limit analysis method for masonry domes composed of interlocking blocks with non-isotropic sliding resistance is under development. This paper reports the first two steps of that work. It first introduces a revision to an existing limit analysis approach using the membrane theory with finite hoop stresses to find the minimum thickness of a hemispherical dome under its own weight and composed of conventional blocks with finite isotropic friction. The coordinates of an initial axisymmetric membrane surface are the optimization variables. During the optimization, the membrane satisfies the equilibrium conditions and meets the sliding constraints where intersects the block interfaces. The results of the revised procedure are compared to those obtained by other approaches finding the thinnest dome. A heuristic method using convex contact model is then introduced to find the sliding resistance of the corrugated interlocking interfaces. Sliding of such interfaces is constrained by the Coulomb’s friction law and by the shear resistance of the locks keeping the blocks together along two orthogonal directions. The role of these two different sliding resistances is discussed and the heuristic method is applied to the revised limit analysis method
Robust exact differentiators with predefined convergence time
The problem of exactly differentiating a signal with bounded second
derivative is considered. A class of differentiators is proposed, which
converge to the derivative of such a signal within a fixed, i.e., a finite and
uniformly bounded convergence time. A tuning procedure is derived that allows
to assign an arbitrary, predefined upper bound for this convergence time. It is
furthermore shown that this bound can be made arbitrarily tight by appropriate
tuning. The usefulness of the procedure is demonstrated by applying it to the
well-known uniform robust exact differentiator, which the considered class of
differentiators includes as a special case
Analysis of explicit and implicit discrete-time equivalent-control based sliding mode controllers
Different time-discretization methods for equivalent-control based sliding
mode control (ECB-SMC) are presented. A new discrete-time sliding mode control
scheme is proposed for linear time-invariant (LTI) systems. It is error-free in
the discretization of the equivalent part of the control input. Results from
simulations using the various discretized SMC schemes are shown, with and
without perturbations. They illustrate the different behaviours that can be
observed. Stability results for the proposed scheme are derived
A Review on Mechanics and Mechanical Properties of 2D Materials - Graphene and Beyond
Since the first successful synthesis of graphene just over a decade ago, a
variety of two-dimensional (2D) materials (e.g., transition
metal-dichalcogenides, hexagonal boron-nitride, etc.) have been discovered.
Among the many unique and attractive properties of 2D materials, mechanical
properties play important roles in manufacturing, integration and performance
for their potential applications. Mechanics is indispensable in the study of
mechanical properties, both experimentally and theoretically. The coupling
between the mechanical and other physical properties (thermal, electronic,
optical) is also of great interest in exploring novel applications, where
mechanics has to be combined with condensed matter physics to establish a
scalable theoretical framework. Moreover, mechanical interactions between 2D
materials and various substrate materials are essential for integrated device
applications of 2D materials, for which the mechanics of interfaces (adhesion
and friction) has to be developed for the 2D materials. Here we review recent
theoretical and experimental works related to mechanics and mechanical
properties of 2D materials. While graphene is the most studied 2D material to
date, we expect continual growth of interest in the mechanics of other 2D
materials beyond graphene
Advances in Discrete-Time Sliding Mode Control Theory and Applications
The focus of this book is on the design of a specific control strategy using digital computers
- …