A Robust 43-GHz VCO in CMOS for OC-768 SONET Applications

In this paper, we present a 43-GHz LC-VCO in 0.13-/spl mu/m CMOS for use in SONET OC-768 optical networks. A tuned output buffer is used to provide 1.3 V/sub p-p/ (single-ended) into a 90-fF capacitive load as is required when the VCO is used in typical clock and data recovery (CDR) circuits. Phase noise is -90 dBc/Hz at a 1-MHz offset from the carrier; this meets SONET jitter specifications. The design has a tune range of 4.2%. The VCO, including output buffers, consumes 14 mA from a 1-V supply and occupies 0.06 mm/sup 2/ of die area. Modern CMOS process characteristics and the high center frequency of this design mean that the tank loss is not dominated by the integrated inductor, but rather by the tank capacitance. An area-efficient inductor design that does not require any optimization is used

Fast synchronization 3R burst-mode receivers for passive optical networks

This paper gives a tutorial overview on high speed burst-mode receiver (BM-RX) requirements, specific for time division multiplexing passive optical networks, and design issues of such BM-RXs as well as their advanced design techniques. It focuses on how to design BM-RXs with short burst overhead for fast synchronization. We present design principles and circuit architectures of various types of burst-mode transimpedance amplifiers, burst-mode limiting amplifiers and burst-mode clock and data recovery circuits. The recent development of 10 Gb/s BM-RXs is highlighted also including dual-rate operation for coexistence with deployed PONs and on-chip auto reset generation to eliminate external timing-critical control signals provided by a PON medium access control. Finally sub-system integration and state-of-the-art system performance for 10 Gb/s PONs are reviewed

A 90 nm CMOS 16 Gb/s Transceiver for Optical Interconnects

Interconnect architectures which leverage high-bandwidth optical channels offer a promising solution to address the increasing chip-to-chip I/O bandwidth demands. This paper describes a dense, high-speed, and low-power CMOS optical interconnect transceiver architecture. Vertical-cavity surface-emitting laser (VCSEL) data rate is extended for a given average current and corresponding reliability level with a four-tap current summing FIR transmitter. A low-voltage integrating and double-sampling optical receiver front-end provides adequate sensitivity in a power efficient manner by avoiding linear high-gain elements common in conventional transimpedance-amplifier (TIA) receivers. Clock recovery is performed with a dual-loop architecture which employs baud-rate phase detection and feedback interpolation to achieve reduced power consumption, while high-precision phase spacing is ensured at both the transmitter and receiver through adjustable delay clock buffers. A prototype chip fabricated in 1 V 90 nm CMOS achieves 16 Gb/s operation while consuming 129 mW and occupying 0.105 mm^2

Analysis and equalization of data-dependent jitter

Data-dependent jitter limits the bit-error rate (BER) performance of broadband communication systems and aggravates synchronization in phase- and delay-locked loops used for data recovery. A method for calculating the data-dependent jitter in broadband systems from the pulse response is discussed. The impact of jitter on conventional clock and data recovery circuits is studied in the time and frequency domain. The deterministic nature of data-dependent jitter suggests equalization techniques suitable for high-speed circuits. Two equalizer circuit implementations are presented. The first is a SiGe clock and data recovery circuit modified to incorporate a deterministic jitter equalizer. This circuit demonstrates the reduction of jitter in the recovered clock. The second circuit is a MOS implementation of a jitter equalizer with independent control of the rising and falling edge timing. This equalizer demonstrates improvement of the timing margins that achieve 10/sup -12/ BER from 30 to 52 ps at 10 Gb/s

Delay Flip-Flop (DFF) Metastability Impact on Clock and Data Recovery (CDR) and Phase-Locked Loop (PLL) Circuits

Modeling delay flip-flops for binary (e.g., Alexander) phase detectors requires paying close attention to three important timing parameters: setup time, hold time, and clock edge-to-output (or briefly C2Q time). These parameters have a critical role in determining the status of the system on the circuit level. This study provided a guideline for designing an optimum DFF for an Alexander phase detector in a clock and data recovery circuit. Furthermore, it indicated DFF timing requirements for a high-speed phase detector in a clock and data recovery circuit. The CDR was also modeled by Verilog-A, and the results were compared with Simulink model achievements. Eventually designed in 45 nm CMOS technology, for 10 Gbps random sequence, the recovered clock contained 0.136 UI and 0.15 UI peak-to-peak jitter on the falling and rising edges respectively, and the lock time was 125 ns. The overall power dissipation was 21 mW from a 1 V supply voltage. Future work includes layout design and manufacturing of the proposed design

Phase Locked Loop (PLL) based Clock and Data Recovery Circuits (CDR) using Calibrated Delay Flip Flop

A Delay Flip Flop (DFF) is used in the phase detector circuit of the clock and data recovery circuit. A DFF consists of the three important timing parameters: setup time, hold time, and clock-to-output delay. These timing parameters play a vital role in designing a system at the transistor level. This thesis paper explains the impact of metastablity on the clock and data recovery (CDR) system and the importance of calibrating the DFF using a metastable circuit to improve a system\u27s lock time and peak-to-peak jitter performance. The DFF was modeled in MATLAB Simulink software and calibrated by adjusting timing parameters. The CDR system was simulated in Simulink for three different cases: 1) equal setup and hold times, 2) setup time greater than the hold time, and 3) hold time greater than the setup time. The Simulink results were then compared with the Cadence simulation results, and it was observed that the calibration of DFF using a metastable circuit improved the CDR system\u27s lock time and jitter tolerance performance. The overall power dissipation of the designed CDR system was 2.4 mW from a 1 volt supply voltage

Influence of jitter on limit cycles in bang-bang clock and data recovery circuits

In bang-bang (BB) clock and data recovery circuits (CDR) limit cycles can occur, but these limit cycles are undesired for a good operation of the BB-CDR. Surprisingly, however, a little bit of noise in the system is beneficial, because it will quench the limit cycles. Until now, authors have always assumed that there is enough noise in a BB-CDR such that no limit cycle occurs. In this work, a pseudo-linear analysis based on describing functions is used to investigate this. In particular, the relationship between the input noise and the amplitude of eventual limit cycles is investigated. An important result of the theory is that it allows to quantify the influence of the different loop parameters on the minimal amount of input jitter needed to destroy the limit cycle. Additionally, for the case that there is not enough noise, the worst case amplitude of the limit cycle (which is unavoidable in this case) is quantified as well. The presented analysis exhibits excellent matching with time domain simulations and leads to very simple analytical expressions

A high speed serializer/deserializer design

A Serializer/Deserializer (SerDes) is a circuit that converts parallel data into a serial stream and vice versa. It helps solve clock/data skew problems, simplifies data transmission, lowers the power consumption and reduces the chip cost. The goal of this project was to solve the challenges in high speed SerDes design, which included the low jitter design, wide bandwidth design and low power design. A quarter-rate multiplexer/demultiplexer (MUX/DEMUX) was implemented. This quarter-rate structure decreases the required clock frequency from one half to one quarter of the data rate. It is shown that this significantly relaxes the design of the VCO at high speed and achieves lower power consumption. A novel multi-phase LC-ring oscillator was developed to supply a low noise clock to the SerDes. This proposed VCO combined an LC-tank with a ring structure to achieve both wide tuning range (11%) and low phase noise (-110dBc/Hz at 1MHz offset). With this structure, a data rate of 36 Gb/s was realized with a measured peak-to-peak jitter of 10ps using 0.18microm SiGe BiCMOS technology. The power consumption is 3.6W with 3.4V power supply voltage. At a 60 Gb/s data rate the simulated peak-to-peak jitter was 4.8ps using 65nm CMOS technology. The power consumption is 92mW with 2V power supply voltage. A time-to-digital (TDC) calibration circuit was designed to compensate for the phase mismatches among the multiple phases of the PLL clock using a three dimensional fully depleted silicon on insulator (3D FDSOI) CMOS process. The 3D process separated the analog PLL portion from the digital calibration portion into different tiers. This eliminated the noise coupling through the common substrate in the 2D process. Mismatches caused by the vertical tier-to-tier interconnections and the temperature influence in the 3D process were attenuated by the proposed calibration circuit. The design strategy and circuits developed from this dissertation provide significant benefit to both wired and wireless applications