An Ultra Low-Power Programmable Voltage Reference for Power-Constrained Electronic Systems

This paper proposes a novel architecture for the generation of a programmable voltage reference: the background- calibrated (BC)-PVR. Our mixed-signal architecture periodically calibrates a static ultra low-power voltage reference generator, from an accurate bandgap reference. The portion of the chip used for the calibration can be powered down with a programmable duty-cycle. The system aims to fully exploit the small temperature derivative vs time DT of several application domains to minimize the average current consumption. The BC-PVR has been designed and implemented in TSMC 55-nm CMOS technology, and it achieves the largest reported programming reference output ◦range [0.42 - 2.52] V, over the temperature range [-20 , 85] C. The duty-cycle mode allows nanoampere current consumption, and the large design flexibility permits to optimize the system performance for the specific application. These features make the BC-PVR very well-suited for power-constrained electronic systems

Design of an Ultra-Low Power RTC for the IoT

The Internet of Things is growing at an exponential rate. This new perception of reality is being researched even further nowadays because society is starting to develop an interest on these technologies. Market potential is increasing even further, since the foreseeable implementations are diverse and still to be detected. The future applications for the IoT are enthusiastic and they will increase the overall quality of life of the citizens of the world. Developing a component that is crucial for the sustainability of this implementation is the task that truly motivates the intended work for this project. Designing the full-custom circuitry and physical layout of a Real Time Clock becomes a job that has a lot of minor details that need considerable attention. These technicalities truly tone the developers skill and knowledge of different design principles. Besides, developing the solution using subthreshold CMOS techniques will put emphasis on different technological procedures. Producing devices that are heavily dependent on PVT variations, operational frequency and power consumption define this new task, that needs a stable approach to all these diverse figure of merits, even though they are all interconnected. The study and understanding of these different approaches allows for a more complex in depth grasp of this recent intriguing proceedings

Circuit Techniques for Low-Power and Secure Internet-of-Things Systems

The coming of Internet of Things (IoT) is expected to connect the physical world to the cyber world through ubiquitous sensors, actuators and computers. The nature of these applications demand long battery life and strong data security. To connect billions of things in the world, the hardware platform for IoT systems must be optimized towards low power consumption, high energy efficiency and low cost. With these constraints, the security of IoT systems become a even more difficult problem compared to that of computer systems. A new holistic system design considering both hardware and software implementations is demanded to face these new challenges. In this work, highly robust and low-cost true random number generators (TRNGs) and physically unclonable functions (PUFs) are designed and implemented as security primitives for secret key management in IoT systems. They provide three critical functions for crypto systems including runtime secret key generation, secure key storage and lightweight device authentication. To achieve robustness and simplicity, the concept of frequency collapse in multi-mode oscillator is proposed, which can effectively amplify the desired random variable in CMOS devices (i.e. process variation or noise) and provide a runtime monitor of the output quality. A TRNG with self-tuning loop to achieve robust operation across -40 to 120 degree Celsius and 0.6 to 1V variations, a TRNG that can be fully synthesized with only standard cells and commercial placement and routing tools, and a PUF with runtime filtering to achieve robust authentication, are designed based upon this concept and verified in several CMOS technology nodes. In addition, a 2-transistor sub-threshold amplifier based "weak" PUF is also presented for chip identification and key storage. This PUF achieves state-of-the-art 1.65% native unstable bit, 1.5fJ per bit energy efficiency, and 3.16% flipping bits across -40 to 120 degree Celsius range at the same time, while occupying only 553 feature size square area in 180nm CMOS. Secondly, the potential security threats of hardware Trojan is investigated and a new Trojan attack using analog behavior of digital processors is proposed as the first stealthy and controllable fabrication-time hardware attack. Hardware Trojan is an emerging concern about globalization of semiconductor supply chain, which can result in catastrophic attacks that are extremely difficult to find and protect against. Hardware Trojans proposed in previous works are based on either design-time code injection to hardware description language or fabrication-time modification of processing steps. There have been defenses developed for both types of attacks. A third type of attack that combines the benefits of logical stealthy and controllability in design-time attacks and physical "invisibility" is proposed in this work that crosses the analog and digital domains. The attack eludes activation by a diverse set of benchmarks and evades known defenses. Lastly, in addition to security-related circuits, physical sensors are also studied as fundamental building blocks of IoT systems in this work. Temperature sensing is one of the most desired functions for a wide range of IoT applications. A sub-threshold oscillator based digital temperature sensor utilizing the exponential temperature dependence of sub-threshold current is proposed and implemented. In 180nm CMOS, it achieves 0.22/0.19K inaccuracy and 73mK noise-limited resolution with only 8865 square micrometer additional area and 75nW extra power consumption to an existing IoT system.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/138779/1/kaiyuan_1.pd

Design of a 2.4 Ghz BAW-Based CMOS Transmitter

In recent years, bulk acoustic wave resonators (BAW) in combination with RF circuits have shown a big potential in achieving the low-power consumption and miniaturization level required to address wireless sensor nodes (WSN) applications. A lot of work has been focused on the receiver side, by integrating BAW resonators with low noise amplifiers (LNA) and in frequency synthesis with the design of BAW-based local oscillators, most of them working at fixed frequency due to their limited tuning range. At the architectural level, this has forced the implementation of several single channel transceivers. This thesis aims at exploring the use of BAW resonators in the transmitter, proposing an architecture capable of taking full advantage of them. The main objective is to develop a transmitter for WSN multi-channel applications able to cover the whole 2.4 GHz ISM band and enable the compatibility with wide-spread standards like Bluetooth and Bluetooth Low Energy. Typical transmissions should thus range from low data rates (typically tens of kb/s) to medium data rates (1 Mb/s), with FSK and GFSK modulation schemes, should be centered on any of the channels provided by these standards and cover a maximum transmission range of some tens of meters. To achieve these targets and circumvent the limited tuning range of the BAW oscillator, an up-conversion transmitter using wide IF is used. The typical spurs problems related to this transmitter architecture are addressed by using a combined suppression based on SSB mixing and selective amplification. The latter is achieved by cointegration of a high efficiency power amplifier with BAW resonators, which allows performing spurs filtering while preserving the efficiency. In particular the selective amplifier is designed by including in the PA analysis the BAW resonator parameters, which allows integrating the BAW filter into the passive network loading the amplifier, participating in the drain voltage shaping. Finally, the frequency synthesis section uses a fractional division plus LC PLL filtering and further integer division to generate the IF signals and exploit the very-low BAW oscillator phase noise. The transmitter has been integrated in a 0.18 µm standard digital CMOS technology. It allows addressing the whole 80 MHz wide 2.4 GHz ISM band. The unmodulated RF frequency carrier demonstrates a very-low phase noise of –136 dBc/Hz at 1 MHz offset. The IF spurs are maintained lower than –48 dBc, satisfying the international regulations for output power up to 10 dBm without the use of any quadrature error compensation in the transmitter. This is achieved thanks to the rejection provided by the SSB mixer and the selective amplifier, which can reach drain efficiency of up to 24% with integrated inductances, including the insertion losses of the BAW filter. The transmitter consumes 35.3 mA at the maximum power of 5.4 dBm under 1.6 V (1.2 V for the PA), while transmitting a 1 Mb/s GFSK signal and complying with both Bluetooth and Bluetooth Low Energy relative and absolute spectrum requirements

In Situ Automatic Analog Circuit Calibration and Optimization

As semiconductor technology scales down, the variations of active/passive device characteristics after fabrication are getting more and more significant. As a result, many circuits need more accuracy margin to meet minimum accuracy specifications over huge process-voltage-temperature (PVT) variations. Although, overdesigning a circuit is sometimes not a feasible option because of excessive accuracy margin that requires high power consumption and large area. Consequently, calibration/tuning circuits that can automatically detect and compensate the variations have been researched for analog circuits to make better trade-offs among accuracy, power consumption, and area. The first part of this dissertation shows that a newly proposed in situ calibration circuit for a current reference can relax the sharp trade-off between the temperature coefficient accuracy and the power consumption of the current reference. Prototype chips fabricated in a 180 nm CMOS technology generate 1 nA and achieve an average temperature coefficient of 289 ppm/°C and an average line sensitivity of 1.4 %/V with no help from a multiple-temperature trimming. Compared with other state-of-the-art current references that do not need a multiple-temperature trimming, the proposed circuit consumes at least 74% less power, while maintaining similar or higher accuracy. The second part of this dissertation proves that a newly proposed multidimensional in situ analog circuit optimization platform can optimize a Tow-Thomas bandpass biquad. Unlike conventional calibration/tuning approaches, which only handle one or two frequency-domain characteristics, the proposed platform optimizes the power consumption, frequency-, and time-domain characteristics of the biquad to make a better trade-off between the accuracy and the power consumption of the biquad. Simulation results show that this platform reduces the gain-bandwidth product of op-amps in the biquad by 80% while reducing the standard deviations of frequency- and time-domain characteristics by 82%. Measurement results of a prototype chip fabricated in a 180 nm CMOS technology also show that this platform can save maximum 71% of the power consumption of the biquad while the biquad maintains its frequency-domain characteristics: Q, ωO and the gain at ωO

Disseny microelectrnic de circuits discriminadors de polsos pel detector LHCb

The aim of this thesis is to present a solution for implementing the front end system of the Scintillator Pad Detector (SPD) of the calorimeter system of the LHCb experiment that will start in 2008 at the Large Hadron Collider (LHC) at CERN. The requirements of this specific system are discussed and an integrated solution is presented, both at system and circuit level. We also report some methodological achievements. In first place, a method to study the PSRR (and any transfer function) in fully differential circuits taking into account the effect of parameter mismatch is proposed. Concerning noise analysis, a method to study time variant circuits in the frequency domain is presented and justified. This would open the possibility to study the effect of 1/f noise in time variants circuits. In addition, it will be shown that the architecture developed for this system is a general solution for front ends in high luminosity experiments that must be operated with no dead time and must be robust against ballistic deficit

Estación meteorológica inalámbrica, de muy bajo consumo e inteligencia embebida

El trabajo aborda la realización de una estación meteorológica alimentada mediante una placa solar. La placa emisora cuenta con una serie de sensores que dan información a cerca de la temperatura, la humedad, la presión y la iluminación. Los datos son recibidos y se implementan algoritmos de predicción del tiempo cuyo resultado es visualizado por el usuario. Uno de los objetivos fundamentales es que el sistema resultante sea de muy bajo consumo para que pueda operar durante largos períodos

Diseño y fabricación de un sistema de control y monitorización de temperatura

Castellano: El presente trabajo forma parte de una serie de trabajos en los cuales se realiza el análisis y diseño teóricos de una maqueta para el estudio de la regulación y el control de procesos térmicos. Dicha maqueta está compuesta principalmente por una resistencia calefactora, cuatro sensores de temperatura y un controlador PID implementado en Arduino. Este trabajo en particular, tiene como finalidad adaptar y ampliar los diseños teóricos previos con el fin de obtener resultados tangibles. Además, se incorpora una aplicación informática. Esta permite controlar el equipo, representar gráficamente los datos adquiridos por los sensores y almacenar dichos datos para su posterior análisis.Inglés: This project is part of a series of projects in which the theoretical analysis and design of a model for the study of the regulation and control of thermal processes is carried out. This model is mainly composed of a heating resistor, four temperature sensors and a PID controller implemented in Arduino. This work in particular aims to adapt and expand previous theoretical designs in order to obtain tangible results. In addition, a computer application is incorporated. This allows you to control the equipment, graphically represent the data acquired by the sensors and store this data for later analysis.Euskera: Lan hau lan batzuen parte da, non prozesu termikoen erregulazioa eta kontrola aztertzeko maketa baten azterketa eta diseinu teorikoak egiten diren. Maketa horren osagai nagusiak hauek dira: erresistentzia berogailua, lau tenperatura-sentsore eta Arduinon ezarritako PID kontrolatzailea. Lan honen helburua da aldez aurreko diseinu teorikoak egokitzea eta zabaltzea, emaitza ukigarriak lortzeko. Gainera, aplikazio informatiko bat gehitu da. Honi esker, ekipoa kontrola daiteke, sentsoreek hartutako datuak grafikoki adieraz daitezke eta datu horiek gorde daitezke, ondoren aztertzeko