Optical Time-Frequency Packing: Principles, Design, Implementation, and Experimental Demonstration

Time-frequency packing (TFP) transmission provides the highest achievable spectral efficiency with a constrained symbol alphabet and detector complexity. In this work, the application of the TFP technique to fiber-optic systems is investigated and experimentally demonstrated. The main theoretical aspects, design guidelines, and implementation issues are discussed, focusing on those aspects which are peculiar to TFP systems. In particular, adaptive compensation of propagation impairments, matched filtering, and maximum a posteriori probability detection are obtained by a combination of a butterfly equalizer and four 8-state parallel Bahl-Cocke-Jelinek-Raviv (BCJR) detectors. A novel algorithm that ensures adaptive equalization, channel estimation, and a proper distribution of tasks between the equalizer and BCJR detectors is proposed. A set of irregular low-density parity-check codes with different rates is designed to operate at low error rates and approach the spectral efficiency limit achievable by TFP at different signal-to-noise ratios. An experimental demonstration of the designed system is finally provided with five dual-polarization QPSK-modulated optical carriers, densely packed in a 100 GHz bandwidth, employing a recirculating loop to test the performance of the system at different transmission distances.Comment: This paper has been accepted for publication in the IEEE/OSA Journal of Lightwave Technolog

Low-complexity iterative receiver design for high spectral efficiency communication systems

University of Technology Sydney. Faculty of Engineering and Information Technology.With the rapid development of the modern society, people have an increasing demand of higher data rate. Due to the limited available bandwidth, how to improve the spectral efficiency becomes a key issue in the next generation wireless systems. Recent researches show that, compared to the conventional orthogonal communication systems, the non-orthogonal system can transmit more information with the same resources by introducing non-orthogonality. The non-orthogonal communication systems can be achieved by using faster-than-Nyquist (FTN) signaling to transmit more data symbols in the same time period. On the other hand, by designing appropriate codebook, the sparse code multiple access (SCMA) system can support more users while preserving the same resource elements. Utilisation of these new technologies leads to challenge in receiver design, which becomes severer in complex channel environments. This thesis studies the receiver design for high spectral efficiency communication systems. The main contributions are as follows: 1. A hybrid message passing algorithm is proposed for faster-than-Nyquist, which solves the problem of joint data detection and channel estimation when the channel coefficients are unknown. To fully exploit the known ISI imposed by FTN signaling, the interference induced by FTN signaling and channel fading are intentionally separated. 2. Gaussian message passing and variational inference based estimation algorithms are proposed for faster-than-Nyquist signaling detection in doubly selective channels. Iterative receivers using mean field and Bethe approximations based on variational inference framework are proposed. Moreover, a novel Gaussian message passing based FTN signaling detection algorithm is proposed. 3. An energy minimisation based SCMA decoding algorithm is proposed and convergence analysis of the proposed algorithm is derived. Following optimisation theory and variational free energy framework, the posterior distribution of data symbol is derived in closed form. Then, the convergence property of the proposed algorithm is analysed. 4. A stretched factor graph is designed for MIMO-SCMA system in order to reduce the receiver complexity. Then, a convergence guaranteed message passing algorithm is proposed by convexifying the Bethe free energy. Finally, cooperative communication methods based on belief consensus and alternative direction method of multipliers are proposed. 5. A low complexity detection algorithm is proposed for faster-than-Nyquist SCMA system, which enables joint channel estimation, decoding and user activity detection in grant-free systems. The combination of FTN signaling with SCMA to further enhance the spectral efficiency is first considered. Then, a merging belief propagation and expectation propagation algorithm is proposed to estimate channel state and perform SCMA decoding

Multicarrier Faster-than-Nyquist Signaling Transceivers: From Theory to Practice

The demand for spectrum resources in cellular systems worldwide has seen a tremendous escalation in the recent past. The mobile phones of today are capable of being cameras taking pictures and videos, able to browse the Internet, do video calling and much more than an yesteryear computer. Due to the variety and the amount of information that is being transmitted the demand for spectrum resources is continuously increasing. Efficient use of bandwidth resources has hence become a key parameter in the design and realization of wireless communication systems. Faster-than-Nyquist (FTN) signaling is one such technique that achieves bandwidth efficiency by making better use of the available spectrum resources at the expense of higher processing complexity in the transceiver. This thesis addresses the challenges and design trade offs arising during the hardware realization of Faster-than-Nyquist signaling transceivers. The FTN system has been evaluated for its achievable performance compared to the processing overhead in the transmitter and the receiver. Coexistence with OFDM systems, a more popular multicarrier scheme in existing and upcoming wireless standards, has been considered by designing FTN specific processing blocks as add-ons to the conventional transceiver chain. A multicarrier system capable of operating under both orthogonal and FTN signaling has been developed. The performance of the receiver was evaluated for AWGN and fading channels. The FTN system was able to achieve 2x improvement in bandwidth usage with similar performance as that of an OFDM system. The extra processing in the receiver was in terms of an iterative decoder for the decoding of FTN modulated signals. An efficient hardware architecture for the iterative decoder reusing the FTN specific processing blocks and realize different functionality has been designed. An ASIC implementation of this decoder was implemented in a 65nm CMOS technology and the implemented chip has been successfully verified for its functionality

Reduced Receivers for Faster-than-Nyquist Signaling and General Linear Channels

Fast and reliable data transmission together with high bandwidth efficiency are important design aspects in a modern digital communication system. Many different approaches exist but in this thesis bandwidth efficiency is obtained by increasing the data transmission rate with the faster-than-Nyquist (FTN) framework while keeping a fixed power spectral density (PSD). In FTN consecutive information carrying symbols can overlap in time and in that way introduce a controlled amount of intentional intersymbol interference (ISI). This technique was introduced already in 1975 by Mazo and has since then been extended in many directions. Since the ISI stemming from practical FTN signaling can be of significant duration, optimum detection with traditional methods is often prohibitively complex, and alternative equalization methods with acceptable complexity-performance tradeoffs are needed. The key objective of this thesis is therefore to design reduced-complexity receivers for FTN and general linear channels that achieve optimal or near-optimal performance. Although the performance of a detector can be measured by several means, this thesis is restricted to bit error rate (BER) and mutual information results. FTN signaling is applied in two ways: As a separate uncoded narrowband communication system or in a coded scenario consisting of a convolutional encoder, interleaver and the inner ISI mechanism in serial concatenation. Turbo equalization where soft information in the form of log likelihood ratios (LLRs) is exchanged between the equalizer and the decoder is a commonly used decoding technique for coded FTN signals. The first part of the thesis considers receivers and arising stability problems when working within the white noise constraint. New M-BCJR algorithms for turbo equalization are proposed and compared to reduced-trellis VA and BCJR benchmarks based on an offset label idea. By adding a third low-complexity M-BCJR recursion, LLR quality is improved for practical values of M. M here measures the reduced number of BCJR computations for each data symbol. An improvement of the minimum phase conversion that sharpens the focus of the ISI model energy is proposed. When combined with a delayed and slightly mismatched receiver, the decoding allows a smaller M without significant loss in BER. The second part analyzes the effect of the internal metric calculations on the performance of Forney- and Ungerboeck-based reduced-complexity equalizers of the M-algorithm type for both ISI and multiple-input multiple-output (MIMO) channels. Even though the final output of a full-complexity equalizer is identical for both models, the internal metric calculations are in general different. Hence, suboptimum methods need not produce the same final output. Additionally, new models working in between the two extremes are proposed and evaluated. Note that the choice of observation model does not impact the detection complexity as the underlying algorithm is unaltered. The last part of the thesis is devoted to a different complexity reducing approach. Optimal channel shortening detectors for linear channels are optimized from an information theoretical perspective. The achievable information rates of the shortened models as well as closed form expressions for all components of the optimal detector of the class are derived. The framework used in this thesis is more general than what has been previously used within the area

On the Impact of Phase Noise in Communication Systems –- Performance Analysis and Algorithms

The mobile industry is preparing to scale up the network capacity by a factor of 1000x in order to cope with the staggering growth in mobile traffic. As a consequence, there is a tremendous pressure on the network infrastructure, where more cost-effective, flexible, high speed connectivity solutions are being sought for. In this regard, massive multiple-input multiple-output (MIMO) systems, and millimeter-wave communication systems are new physical layer technologies, which promise to facilitate the 1000 fold increase in network capacity. However, these technologies are extremely prone to hardware impairments like phase noise caused by noisy oscillators. Furthermore, wireless backhaul networks are an effective solution to transport data by using high-order signal constellations, which are also susceptible to phase noise impairments. Analyzing the performance of wireless communication systems impaired by oscillator phase noise, and designing systems to operate efficiently in strong phase noise conditions are critical problems in communication theory. The criticality of these problems is accentuated with the growing interest in new physical layer technologies, and the deployment of wireless backhaul networks. This forms the main motivation for this thesis where we analyze the impact of phase noise on the system performance, and we also design algorithms in order to mitigate phase noise and its effects. First, we address the problem of maximum a posteriori (MAP) detection of data in the presence of strong phase noise in single-antenna systems. This is achieved by designing a low-complexity joint phase-estimator data-detector. We show that the proposed method outperforms existing detectors, especially when high order signal constellations are used. Then, in order to further improve system performance, we consider the problem of optimizing signal constellations for transmission over channels impaired by phase noise. Specifically, we design signal constellations such that the error rate performance of the system is minimized, and the information rate of the system is maximized. We observe that these optimized constellations significantly improve the system performance, when compared to conventional constellations, and those proposed in the literature. Next, we derive the MAP symbol detector for a MIMO system where each antenna at the transceiver has its own oscillator. We propose three suboptimal, low-complexity algorithms for approximately implementing the MAP symbol detector, which involve joint phase noise estimation and data detection. We observe that the proposed techniques significantly outperform the other algorithms in prior works. Finally, we study the impact of phase noise on the performance of a massive MIMO system, where we analyze both uplink and downlink performances. Based on rigorous analyses of the achievable rates, we provide interesting insights for the following question: how should oscillators be connected to the antennas at a base station, which employs a large number of antennas

Synchronization in all-digital QAM receivers

The recent advance in Field Programmable Gate Array (FPGA) technology has been largely embraced by the communication industry, which views this technology as an effective and economical alternative to the design of Application Specific Integrated Circuits (ASICs). The primary reasons for switching to FPGAs are lower development and non-recurring engineering costs, the flexibility to design to a preliminary standard and adapt the design as the standard evolves, as well as the option of performing software updates in the field. A sector with strong interest in FPGAs is the coaxial cable TV/Internet distribution industry. The creation of soft preliminary standards by the standards organization governing the industry has been the main catalyst for the massive adoption of FPGAs by small to medium size companies, which see this technology as an opportunity to compete in this open market. Both the circuit speed and the economy of FPGA technology depend upon using algorithms that map efficiently into its fabric. Often it is prudent to sacrifice performance to improve either clock speed or economy when developing with FPGAs. The purpose of this research is to both revise and devise synchronization algorithms / structures for cable digital receivers that are to be implemented in FPGA. The main communication scheme used by the coaxial cable distribution industry is digital Quadrature Amplitude Modulation (QAM). The problem of synchronizing to the QAM signal in the receiver is not a new topic and several synchronization-related circuits, which were devised with ASICs implementation in mind, can be found in the open literature. Of interest in this thesis is the non-data-aided digital timing synchronizer that was proposed by D'Andrea to recover timing with no knowledge of the transmitted data. Accurate timing estimation was achieved by reshaping the received signal with a prefilter prior to estimating the timing. A problem with D'Andrea's synchronizer is that the prefilter for reshaping the signal is a relatively long Finite Impulse Response (FIR) filter, whose implementation requires a large number of multipliers. This may not have been an issue with ASICs in as much as the number of hardwired multipliers on a chip is not limited as it is in an FPGA chip. One contribution in this research is to propose an alternative to D'Andrea's synchronizer by replacing the long FIR filter with two single-pole Infinite Impulse Response (IIR) filters that are directly placed inside the timing recovery loop. This novel architecture, which drastically reduces the number of multipliers, is well suited for FPGA implementation. Non-data-aided feedforward synchronizers, which use the same prefilter as D'Andrea's synchronizer, have been receiving significant attention in recent years. Detailed performance analysis for these synchronizers can be found in the open literature. These synchronizers have the advantage of using a feedfordward structure rather than a feedback structure, as it is the case in D'Andrea's synchronizer, to estimate the timing. While D'Andrea's synchronizer has an advantage in performance over a non-data-aided feedforward synchronizer, this has not been reported in the literature. In this thesis a second contribution consists of thoroughly analyzing the steady state timing jitter in D'Andrea synchronizer by deriving a closed-form expression for the noise power spectrum and a simple equation to estimate the timing jitter variance. A third contribution is a novel low-complexity and fast acquisition coherent detector for the detection of Quadrature Phase Shift Keying (QPSK) (i.e., 4-QAM) symbols. This detector performs carrier phase synchronization much faster than a conventional coherent detector. The acquisition time is comparable to that of a differential detector. The fast acquisition comes at the expense of phase jitter, and the end result is a 1 dB performance loss over theoretical coherent detection. This detector can be used in place of the differential detector with no economic penalty. Doing so yields a performance advantage of about 2 dB over differential detection

Transmissores-recetores de baixa complexidade para redes óticas

Traditional coherent (COH) transceivers allow encoding of information in both quadratures and the two orthogonal polarizations of the electric field. Nevertheless, such transceivers used today are based on the intradyne scheme, which requires two 90o optical hybrids and four pairs of balanced photodetectors for dual-polarization transmission systems, making its overall cost unattractive for short-reach applications. Therefore, SSB methods with DD reception, commonly referred to as self-coherent (SCOH) transceivers, can be employed as a cost-effective alternative to the traditional COH transceivers. Nevertheless, the performance of SSB systems is severely degraded. This work provides a novel SCOH transceiver architecture with improved performance for short-reach applications. In particular, the development of phase reconstruction digital signal processing (DSP) techniques, the development of other DSP subsystems that relax the hardware requirement, and their performance optimization are the main highlights of this research. The fundamental principle of the proposed transceiver is based on the reception of the signal that satisfies the minimum phase condition upon DD. To reconstruct the missing phase information imposed by DD, a novel DCValue method exploring the SSB and the DC-Value properties of the minimum phase signal is developed in this Ph.D. study. The DC-Value method facilitates the phase reconstruction process at the Nyquist sampling rate and requires a low intensity pilot signal. Also, the experimental validation of the DC-Value method was successfully carried out for short-reach optical networks. Additionally, an extensive study was performed on the DC-Value method to optimize the system performance. In the optimization process, it was found that the estimation of the CCF is an important parameter to exploit all advantages of the DC-Value method. A novel CCF estimation technique was proposed. Further, the performance of the DC-Value method is optimized employing the rate-adaptive probabilistic constellation shaping.Os sistemas de transcetores coerentes tradicionais permitem a codificação de informação em ambas quadraturas e em duas polarizações ortogonais do campo elétrico. Contudo, estes transcetores utilizados atualmente são baseados num esquema intradino, que requer dois híbridos óticos de 90o e quatro pares de foto detetores para sistemas de transmissão com polarização dupla, fazendo com que o custo destes sistemas seja pouco atrativo para aplicações de curto alcance. Por isso, métodos de banda lateral única com deteção direta, também referidos como transcetores coerentes simplificados, podem ser implementados como uma alternativa de baixo custo aos sistemas coerentes tradicionais. Contudo, o desempenho de sistemas de banda lateral única tradicionais é gravemente degradado pelo batimento sinal-sinal. Nesta tese foi desenvolvida uma nova arquitetura de transcetor coerente simplificada com um melhor desempenho para aplicações de curto alcance. Em particular, o desenvolvimento de técnicas de processamento digital de sinal para a reconstrução de fase, bem como de outros subsistemas de processamento digital de sinal que minimizem os requerimentos de hardware e a sua otimização de desempenho são o foco principal desta tese. O princípio fundamental do transcetor proposto é baseado na receção de um sinal que satisfaz a condição mínima de fase na deteção direta. Para reconstruir a informação de fase em falta causada pela deteção direta, um novo método de valor DC que explora sinais de banda lateral única e as propriedades DC da condição de fase mínima é desenvolvido nesta tese. O método de valor DC facilita a reconstrução da fase à frequência de amostragem de Nyquist e requer um sinal piloto de baixa intensidade. Além disso, a validação experimental do método de valor DC foi executada com sucesso em ligações óticas de curto alcance. Adicionalmente, foi realizado um estudo intensivo do método de valor DC para otimizar o desempenho do sistema. Neste processo de otimização, verificou-se que o fator de contribuição da portadora é um parâmetro importante para explorar todas as vantagens do método de valor DC. Neste contexto, é proposto um novo método para a sua estimativa. Por último, o desempenho do método de valor DC é otimizado recorrendo a mapeamento probabilístico de constelação com taxa adaptativa.Programa Doutoral em Engenharia Eletrotécnic

Advanced low-complexity multiuser receivers

It tema centrale di questa tesi è la rivelazione multi-utente per sistemi di comunicazione wireless ad elevata efficienza spettrale. Lo scopo del lavoro è quello di proporre nuovi ricevitori multi-utente a bassa complessità con elevate prestazioni. Sono considerati sistemi satellitari basati su FDM (Frequency Division Multiplexing), in cui ogni utente adotta una modulazione CPM (Continuous Phase Modulation) concatenata serialmente con un codificatore tramite un interlacciatore e decodifica iterativa. Si considerano, inoltre, canali lineari in presenza di AWGN (additive white Gaussian noise). In particolare, si studiano sistemi FDM, in cui i canali adiacenti possono sovrapporsi in frequenza per aumentere l'efficienza spettrale, e sistemi CDMA (code division multiple access). Per gli scenari presi in esame, proponiamo schemi di rivelazione con un eccellente compromesso tra prestazioni e complessità computazionale, che permettono di implementare schemi di trasmissione con straordinaria efficienza spettrale, al prezzo di un limitato aumento di complessità rispetto ad un classico ricevitore singolo-utente che ignora l'interferenza.This thesis deals with multiuser detection (MUD) for spectrally-efficient wireless communication systems. The aim of this work is to propose new advanced low-complexity multiuser receivers with near-optimal detection performance. We consider frequency division multiplexing (FDM) satellite systems where each user employs a continuous phase modulation (CPM), serially concatenated with an outer code through an interleaver, and iterative detection/decoding. We also consider linear channels impaired by additive white Gaussian noise (AWGN), focusing on FDM systems where adjacent channels are allowed to overlap in frequency, and on code division multiple access systems (CDMA). For the considered scenarios, we propose detection schemes with an excel- lent performance/complexity tradeoff which allow us to implement transmission schemes with unprecedented spectral efficiency at a price of a limited complexity increase with respect to a classical single-user receiver which neglects the interference