A parsimonious model for the proportional control valve

A generic non-linear dynamic model of a direct-acting electrohydraulic proportional solenoid valve is presented. The valve consists of two subsystems-s-a spool assembly and one or two unidirectional proportional solenoids. These two subsystems are modelled separately. The solenoid is modelled as a non-linear resistor-inductor combination, with inductance parameters that change with current. An innovative modelling method has been used to represent these components. The spool assembly is modelled as a mass-spring-damper system. The inertia and the damping effects of the solenoid armature are incorporated in the spool mode1. The model accurately and reliably predicts both the dynamic and steady state responses of the valve to voltage inputs. Simulated results are presented, which agree well with experimental results

Automatic controllers for the Apollo LCG Final report

Automatic controllers for liquid cooling garment of Apollo full pressure sui

Flight control systems properties and problems, volume 1

This volume contains a delineation of fundamental and mechanization-specific flight control characteristics and problems gleaned from many sources and spanning a period of over two decades. It is organized to present and discuss first some fundamental, generic problems of closed-loop flight control systems involving numerator characteristics (quadratic dipoles, non-minimum phase roots, and intentionally introduced zeros). Next the principal elements of the largely mechanical primary flight control system are reviewed with particular emphasis on the influence of nonlinearities. The characteristics and problems of augmentation (damping, stability, and feel) system mechanizations are then dealt with. The particular idiosyncracies of automatic control actuation and command augmentation schemes are stressed, because they constitute the major interfaces with the primary flight control system and an often highly variable vehicle response

Advanced Control Strategies for Mobile Hydraulic Applications

Mobile hydraulic machines are affected by numerous undesired dynamics, mainly discontinuous motion and vibrations. Over the years, many methods have been developed to limit the extent of those undesired dynamics and improve controllability and safety of operation of the machine. However, in most of the cases, today\u27s methods do not significantly differ from those developed in a time when electronic controllers were slower and less reliable than they are today. This dissertation addresses this aspect and presents a unique control method designed to be applicable to all mobile hydraulic machines controlled by proportional directional valves. In particular, the proposed control method is targeted to hydraulic machines such as those used in the field including construction (wheel loaders, excavators, and backhoes, etc.), load handling (cranes, reach-stackers, and aerial lift, etc.), agriculture (harvesters, etc.), forestry, and aerospace. For these applications the proposed control method is designed to achieve the following goals: A. Improvement of the machine dynamics by reducing mechanical vibrations of mechanical arms, load, as well as operator seat; B. Reduction of the energy dissipation introduced by current vibration damping methods; C. Reduction of system slowdowns introduced by current vibration damping methods. Goal A is generally intended for all machines; goal B refers to those applications in which the damping is introduced by means of energy losses on the main hydraulic transmission line; goal C is related to those applications in which the vibration attenuation is introduced by slowing down the main transmission line dynamics. Two case studies are discussed in this work: 1. Hydraulic crane: the focus is on the vibrations of the mechanical arms and load (goals A and B). 2. Wheel loader: the focus is on the vibrations of the driver\u27s seat and bucket (goals A and C). The controller structure is basically unvaried for different machines. However, what differs in each application are the controller parameters, whose adaptation and tuning method represent the main innovations of this work. The proposed controller structure is organized so that the control parameters are adapted with respect to the instantaneous operating point which is identified by means of feedback sensors. The Gain Scheduling technique is used to implement the controller whose set of parameters are function of the specific identified operating point. The optimal set of control parameters for each operating point is determined through the non-model-based controller tuning. The technique determines the optimal set of controller parameters through the optimization of the experimental machine dynamics. The optimization is based on an innovative application of the Extremum Seeking algorithm. The optimal controller parameters are then indexed into the Gain Scheduler. The proposed method does not require the modification of the standard valve controlled machine layout since it only needs for the addition of feedback sensors. The feedback signals are used by the control unit to modify the electric currents to the proportional directional valves and cancel the undesired dynamics of the machine by controlling the actuator motion. In order for the proposed method to be effective, the proportional valve bandwidth must be significantly higher than the frequency of the undesired dynamics. This condition, which is typically true for heavy machineries, is further investigated in the research. The research mostly focuses on the use of pressure feedback. In fact, although the use of position, velocity, or acceleration sensors on the vibrating bodies of the machine would provide a more straightforward measurement of the vibration, they are extremely rare on mobile hydraulic machines where mechanical and environmental stress harm their integrity. A comparison between pressure feedback and acceleration feedback alternatives of the proposed method is investigated with the aim to outline the conditions making one alternative preferable over the other one (for those applications were both alternatives are technically viable in terms of sensors and wiring reliability). A mid-sized hydraulic crane (case study 1) was instrumented at Maha Fluid Power Research Center to study the effectiveness of the proposed control method, its stability and its experimental validation. Up to 30% vibration damping and 40% energy savings were observed for a specific cycle over the standard vibration damping method for this application. The proposed control method was also applied to a wheel loader (case study 2), and up to 70% vibrations attenuation on the bucket and 30% on the driver\u27s cab were found in simulations. These results also served to demonstrate the applicability of the control method to different hydraulic machines. Improved system response and a straightforward controller parameters tuning methodology are the features which give to the proposed method the potential to become a widespread technology for fluid power machines. The proposed method also has potential for improving several current vibration damping methods in terms of energy efficiency as well as simplification of both the hydraulic system layout and tuning process

Cavitation Inception in Spool Valves

Cavitation has been investigated in directional control valves in order to identify damage mechanisms characteristic of components of aircraft hydraulic systems. Tests have been conducted in a representative metal spool valve and in a model three times larger. Data taken under noncavitating conditions with both valves showed that the position of the high-velocity annular jet shifts orientation, depending upon valve opening and Reynolds number. By means of high-frequency response pressure transducers strategically placed in the valve chamber cavitation could be sensed by the correlation of noise with a cavitation index. The onset of cavitation can be detected by comparing energy spectra for a fixed valve opening and a constant discharge. Another sensitive indicator of cavitation inception is the ratio of cavitating to noncavitating spectral densities. The incipient cavitation number as defined in this investigation is correlated with the Reynolds number for both valves

Evaluation of steady flow torques and pressure losses in a rotary flow control valve by means of computational fluid dynamics.

In this paper, a novel design of a rotary hydraulic flow control valve has been presented for high flow rate fluid power systems. High flow rates in these systems account for substantial flow forces acting on the throttling elements of the valves and cause the application of mechanically sophisticated multi-staged servo valves for flow regulation. The suggested design enables utilisation of single-stage valves in power hydraulics operating at high flow rates regimes. A spool driver and auxiliary mechanisms of the proposed valve design were discussed and selection criteria were suggested. Analytical expressions for metering characteristics as well as steady flow torques have been derived. Computational fluid dynamics (CFD) analysis of steady state flow regimes was conducted to evaluate the hydraulic behaviour of the proposed valve. This study represents a special case of an independent metering concept applied to the design of power hydraulic systems with direct proportional valve control operating at flow rates above 150 litres per minute. The result gained using parametric CFD simulations predicted the induced torque and the pressure drops due to a steady flow. Magnitudes of these values prove that by minimising the number of spool’s mobile metering surfaces it is possible to reduce the flow-generated forces in the new generation of hydraulic valves proposed in this study. Calculation of the flow jet angles was analytically verified by measuring the deflection of the velocity vector using flow velocity field distribution, obtained during visualisation of the results of CFD simulations. The derived calculation formulas can predict metering characteristics, values of steady flow torques and jet angles for the specified design and geometry of the suggested valve. The proposed novel structure of the flow control valve promises to attain improved controllability, reliability and efficiency of the hydraulic control units of heavy mobile machinery operating at high flow rates regimes

Water management system and an electrolytic cell therefor Patent

Description of electrical equipment and system for purification of waste water by producing silver ions for bacterial contro