Integrating power flow modelling with building simulation

The inclusion of photovoltaic facades and other local sources of both heat and power within building designs has given rise to the concept of embedded generation: where some or all of the heat and power demands are produced close to the point of use. This paper describes recent work to simulate the heat and power flows associated with both an embedded generation system and the building it serves. This is achieved through the development of an electrical power flow model and its integration within the ESP-r simulation program

Design of an Adaptive Neurofuzzy Inference Control System for the Unified Power-Flow Controller

This paper presents a new approach to control the operation of the unified power-flow controller (UPFC) based on the adaptive neurofuzzy inference controller (ANFIC) concept. The training data for the controller are extracted from an analytical model of the transmission system incorporating a UPFC. The operating points' space is dynamically partitioned into two regions: 1) an inner region where the desired operating point can be achieved without violating any of the UPFC constraints and 2) an outer region where it is necessary to operate the UPFC beyond its limits. The controller is designed to achieve the most appropriate operating point based on the real power priority. In this study, the authors investigated and analyzed the effect of the system short-circuit level on the UPFC operating feasible region which defines the limitation of its parameters. In order to illustrate the effectiveness of the control algorithm, simulation and experimental studies have been conducted using the MATLAB/SIMULINK and dSPACE DS1103 data-acquisition board. The obtained results show a clear agreement between simulation and experimental results which verify the effective performance of the ANFIC controller

Modelling and simulation of small-scale embedded generation systems

Advances in heat and power production are leading to a revolution in how buildings are perceived as an energy system. The rapid development of fuel cells, photovoltaic facades, cogeneration and the evolution of ducted windturbines allows the designer to envisage a building providing much of its own heat and power through local embedded generation (EG). However, the addition of heat and power production to the building increases it complexityas an energy system. New design issues must be addressed such as the integration of EG with traditional HVAC and power systems; optimal demand and supply matching; demand side management and its impact on environmentalperformance; interaction of the EG system with the local electricity network, etc

Power waves formulation of oscillation conditions: avoidance of bifurcation modes in cross-coupled VCO architectures

This paper discusses necessity of power-waves formulation to extend voltage-current oriented approaches based on linear concepts such as admittance/impedance operators and transfer-function representations. Importance of multi-physics methodologies, throughout power-waves formulation, for the analysis and design of crystal oscillators is discussed. Interpretation of bifurcation modes in differential cross-coupled VCO architectures in terms of gyrator-like behavior, is proposed. Impact of amplitude level control (ALC) on large-signal phase noise performances is underlined showing necessity of robust control analysis approach relative to power-energy considerations

Power Flow Modelling of Dynamic Systems - Introduction to Modern Teaching Tools

As tools for dynamic system modelling both conventional methods such as transfer function or state space representation and modern power flow based methods are available. The latter methods do not depend on energy domain, are able to preserve physical system structures, visualize power conversion or coupling or split, identify power losses or storage, run on conventional software and emphasize the relevance of energy as basic principle of known physical domains. Nevertheless common control structures as well as analysis and design tools may still be applied. Furthermore the generalization of power flow methods as pseudo-power flow provides with a universal tool for any dynamic modelling. The phenomenon of power flow constitutes an up to date education methodology. Thus the paper summarizes fundamentals of selected power flow oriented modelling methods, presents a Bond Graph block library for teaching power oriented modelling as compact menu-driven freeware, introduces selected examples and discusses special features.Comment: 12 pages, 9 figures, 4 table

DSOGI-PLL based power control method to mitigate control errors under disturbances of grid connected hybrid renewable power systems

The control of power converter devices is one of the main research lines in interfaced renewable energy sources, such as solar cells and wind turbines. Therefore, suitable control algorithms should be designed in order to regulate power or current properly and attain a good power quality for some disturbances, such as voltage sag/swell, voltage unbalances and fluctuations, long interruptions, and harmonics. Various synchronisation techniques based control strategies are implemented for the hybrid power system applications under unbalanced conditions in literature studies. In this paper, synchronisation algorithms based Proportional-Resonant (PR) power/current controller is applied to the hybrid power system (solar cell + wind turbine + grid), and Dual Second Order Generalized Integrator-Phase Locked Loop (DSOGI-PLL) based PR controller in stationary reference frame provides a solution to overcome these problems. The influence of various cases, such as unbalance, and harmonic conditions, is examined, analysed and compared to the PR controllers based on DSOGI-PLL and SRF-PLL. The results verify the effectiveness and correctness of the proposed DSOGI-PLL based power control method

A Structured Hardware/Software Architecture for Embedded Sensor Nodes

Owing to the limited requirement for sensor processing in early networked sensor nodes, embedded software was generally built around the communication stack. Modern sensor nodes have evolved to contain significant on-board functionality in addition to communications, including sensor processing, energy management, actuation and locationing. The embedded software for this functionality, however, is often implemented in the application layer of the communications stack, resulting in an unstructured, top-heavy and complex stack. In this paper, we propose an embedded system architecture to formally specify multiple interfaces on a sensor node. This architecture differs from existing solutions by providing a sensor node with multiple stacks (each stack implements a separate node function), all linked by a shared application layer. This establishes a structured platform for the formal design, specification and implementation of modern sensor and wireless sensor nodes. We describe a practical prototype of an intelligent sensing, energy-aware, sensor node that has been developed using this architecture, implementing stacks for communications, sensing and energy management. The structure and operation of the intelligent sensing and energy management stacks are described in detail. The proposed architecture promotes structured and modular design, allowing for efficient code reuse and being suitable for future generations of sensor nodes featuring interchangeable components

Power quality and electromagnetic compatibility: special report, session 2

The scope of Session 2 (S2) has been defined as follows by the Session Advisory Group and the Technical Committee: Power Quality (PQ), with the more general concept of electromagnetic compatibility (EMC) and with some related safety problems in electricity distribution systems. Special focus is put on voltage continuity (supply reliability, problem of outages) and voltage quality (voltage level, flicker, unbalance, harmonics). This session will also look at electromagnetic compatibility (mains frequency to 150 kHz), electromagnetic interferences and electric and magnetic fields issues. Also addressed in this session are electrical safety and immunity concerns (lightning issues, step, touch and transferred voltages). The aim of this special report is to present a synthesis of the present concerns in PQ&EMC, based on all selected papers of session 2 and related papers from other sessions, (152 papers in total). The report is divided in the following 4 blocks: Block 1: Electric and Magnetic Fields, EMC, Earthing systems Block 2: Harmonics Block 3: Voltage Variation Block 4: Power Quality Monitoring Two Round Tables will be organised: - Power quality and EMC in the Future Grid (CIGRE/CIRED WG C4.24, RT 13) - Reliability Benchmarking - why we should do it? What should be done in future? (RT 15