Design of Power Management Integrated Circuits and High-Performance ADCs

A battery-powered system has widely expanded its applications to implantable medical devices (IMDs) and portable electronic devices. Since portable devices or IMDs operate in the energy-constrained environment, their low-power operations in combination with efficiently sourcing energy to them are key problems to extend device life. This research proposes novel circuit techniques for two essential functions of a power receiving unit (PRU) in the energy-constrained environment, which are power management and signal processing. The first part of this dissertation discusses power management integrated circuits for a PRU. From a power management perspective, the most critical two circuit blocks are a front-end rectifier and a battery charger. The front-end CMOS active rectifier converts transmitted AC power into DC power. High power conversion efficiency (PCE) is required to reduce power loss during the power transfer, and high voltage conversion ratio (VCR) is required for the rectifier to enable low-voltage operations. The proposed 13.56-MHz CMOS active rectifier presents low-power circuit techniques for comparators and controllers to reduce increasing power loss of an active diode with offset/delay calibration. It is implemented with 5-V devices of a 0.35 µm CMOS process to support high voltage. A peak PCE of 89.0%, a peak VCR of 90.1%, and a maximum output power of 126.7 mW are measured for 200Ω loading. The linear battery charger stores the converted DC power into a battery. Since even small power saving can be enough to run the low-power PRU, a battery charger with low IvQ is desirable. The presented battery charger is based on a single amplifier for regulation and the charging phase transition from the constant-current (CC) phase to the constant-voltage (CV) phase. The proposed unified amplifier is based on stacked differential pairs which share the bias current. Its current-steering property removes multiple amplifiers for regulation and the CC-CV transition, and achieves high unity-gain loop bandwidth for fast regulation. The charger with the maximum charging current of 25 mA is implemented in 0.35 µm CMOS. A peak charger efficiency of 94% and average charger efficiency of 88% are achieved with an 80-mAh Li-ion polymer battery. The second part of this dissertation focuses on analog-to-digital converters (ADCs). From a signal processing perspective, an ADC is one of the most important circuit blocks in the PRU. Hence, an energy-efficient ADC is essential in the energy-constrained environment. A pipelined successive approximation register (SAR) ADC has good energy efficiency in a design space of moderate-to-high speeds and resolutions. Process-Voltage-Temperature variations of a dynamic amplifier in the pipelined-SAR ADC is a key design issue. This research presents two dynamic amplifier architectures for temperature compensation. One is based on a voltage-to-time converter (VTC) and a time-to-voltage converter (TVC), and the other is based on a temperature-dependent common-mode detector. The former amplifier is adopted in a 13-bit 10-50 MS/s subranging pipelined-SAR ADC fabricated in 0.13-µm CMOS. The ADC can operate under the power supply voltage of 0.8-1.2 V. Figure-of-Merits (FoMs) of 4-11.3 fJ/conversion-step are achieved. The latter amplifier is also implemented in 0.13-µm CMOS, consuming 0.11 mW at 50 MS/s. Its measured gain variation is 2.1% across the temperature range of -20°C to 85 °C

Communication and energy delivery architectures for personal medical devices

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2012.Cataloged from PDF version of thesis.Includes bibliographical references (p. 219-232).Advances in sensor technologies and integrated electronics are revolutionizing how humans access and receive healthcare. However, many envisioned wearable or implantable systems are not deployable in practice due to high energy consumption and anatomically-limited size constraints, necessitating large form-factors for external devices, or eventual surgical re-implantation procedures for in-vivo applications. Since communication and energy-management sub-systems often dominate the power budgets of personal biomedical devices, this thesis explores alternative usecases, system architectures, and circuit solutions to reduce their energy burden. For wearable applications, a system-on-chip is designed that both communicates and delivers power over an eTextiles network. The transmitter and receiver front-ends are at least an order of magnitude more efficient than conventional body-area networks. For implantable applications, two separate systems are proposed that avoid reimplantation requirements. The first system extracts energy from the endocochlear potential, an electrochemical gradient found naturally within the inner-ear of mammals, in order to power a wireless sensor. Since extractable energy levels are limited, novel sensing, communication, and energy management solutions are proposed that leverage duty-cycling to achieve enabling power consumptions that are at least an order of magnitude lower than previous work. Clinical measurements show the first system demonstrated to sustain itself with a mammalian-generated electrochemical potential operating as the only source of energy into the system. The second system leverages the essentially unlimited number of re-charge cycles offered by ultracapacitors. To ease patient usability, a rapid wireless capacitor charging architecture is proposed that employs a multi-tapped secondary inductive coil to provide charging times that are significantly faster than conventional approaches.by Patrick Philip Mercier.Ph.D

Antenna Systems

This book offers an up-to-date and comprehensive review of modern antenna systems and their applications in the fields of contemporary wireless systems. It constitutes a useful resource of new material, including stochastic versus ray tracing wireless channel modeling for 5G and V2X applications and implantable devices. Chapters discuss modern metalens antennas in microwaves, terahertz, and optical domain. Moreover, the book presents new material on antenna arrays for 5G massive MIMO beamforming. Finally, it discusses new methods, devices, and technologies to enhance the performance of antenna systems

ワイヤレス電力伝送システムにおける二次側のみの制御による電力と効率の同時制御法の開発研究

学位の種別: 課程博士審査委員会委員 : （主査）東京大学教授 堀 洋一, 東京大学教授 大崎 博之, 東京大学教授 古関 隆章, 東京大学准教授 藤本 博志, 東京大学准教授 馬場 旬平, 東京大学准教授 川原 圭博University of Tokyo(東京大学

Multi-gigabit CMOS analog-to-digital converter and mixed-signal demodulator for low-power millimeter-wave communication systems

The objective of the research is to develop high-speed ADCs and mixed-signal demodulator for multi-gigabit communication systems using millimeter-wave frequency bands in standard CMOS technology. With rapid advancements in semiconductor technologies, mobile communication devices have become more versatile, portable, and inexpensive over the last few decades. However, plagued by the short lifetime of batteries, low power consumption has become an extremely important specification in developing mobile communication devices. The ever-expanding demand of consumers to access and share information ubiquitously at faster speeds requires higher throughputs, increased signal-processing functionalities at lower power and lower costs. In today’s technology, high-speed signal processing and data converters are incorporated in almost all modern multi-gigabit communication systems. They are key enabling technologies for scalable digital design and implementation of baseband signal processors. Ultimately, the merits of a high performance mixed-signal receiver, such as data rate, sensitivity, signal dynamic range, bit-error rate, and power consumption, are directly related to the quality of the embedded ADCs. Therefore, this dissertation focuses on the analysis and design of high-speed ADCs and a novel broadband mixed-signal demodulator with a fully-integrated DSP composed of low-cost CMOS circuitry. The proposed system features a novel dual-mode solution to demodulate multi-gigabit BPSK and ASK signals. This approach reduces the resolution requirement of high-speed ADCs, while dramatically reducing its power consumption for multi-gigabit wireless communication systems.PhDGee-Kung Chang - Committee Chair; Chang-Ho Lee - Committee Member; Geoffrey Ye Li - Committee Member; Paul A. Kohl - Committee Member; Shyh-Chiang Shen - Committee Membe

Compact Multi-Coil Inductive Power Transfer System with a Dynamic Receiver Position Estimation

Inductive power transfer (IPT) systems with tolerance to the lateral misalignment are advantageous for enhancing the transmitted power, usability and security of the system. In this thesis, a misalignment tolerant multi-coil design is proposed to supply stationary and dynamic battery-free wireless devices. A compact architecture composed of individually switchable 3 layers of printed coils arranged with overlap for excellent surface coverage. A hybrid architecture based on three compact AC supply modules reduces the supply circuit complexity on the sending Seite 2 von 4side. It detects the position of the receiver coil quickly, controls the activation of the transmitting coils and estimates the next receiver position. The proposed architecture reduces the circuit footprint by a factor of 62% compared to common architectures. A transmitter coil activation strategy is proposed based on the detection of the transmitting coils voltage and communication between sending side and receiving side to detect devices to supply nature and position and to differentiate them from other conductive objects in the sending area to the supplying security. The experimental results prove that the proposed architecture has a good performance for different trajectories when the device speed does not exceed 15 mm/s. Besides, the maximum detection time for the initial device position is about 1.6 s. The maximal time interval to check the transmitter coils is around 0.7 s.:1. INTRODUCTION 2. THEORETICAL BACKGROUND 3. STATE OF THE ART OF MULTI-COIL IPT SYSTEMS 4. NOVEL DESIGN OF A MULTI-COIL IPT SYSTEM 5. MULTI-COIL ACTIVATION PROCEDURE 6. EXPERIMENTAL INVESTIGATIONS 7. CONCLUSION AND OUTLOOKInduktive Energieübertragungssysteme (IPT) mit Toleranz gegenüber seitlichem Versatz sind vorteilhaft, um die übertragene Leistung, die Nutzbarkeit und die Sicherheit des Systems zu verbessern. In dieser Arbeit wird ein versatztolerantes Multispulen-Design vorgeschlagen, um stationäre und dynamische batterielose drahtlose Geräte zu versorgen. Die kompakte Architektur besteht aus 3 einzeln schaltbaren Schichten gedruckter Spulen, die überlappend angeordnet sind, um eine hervorragende Oberflächenabdeckung zu gewährleisten. Eine hybride Architektur, die auf drei kompakten AC-Versorgungsmodulen basiert, reduziert die Komplexität der Versorgungsschaltung auf der Senderseite. Sie erkennt die Position der Empfängerspule schnell, steuert die Aktivierung der Sendespulen und schätzt die nächste Empfängerposition. Die vorgeschlagene Architektur reduziert den Platzbedarf der Schaltung um einen Faktor von 62 % im Vergleich zu herkömmlichen Architekturen. Es wird eine Aktivierungsstrategie für die Sendespulen vorgeschlagen, die auf der Erkennung der Spannung der Sendespulen und der Kommunikation zwischen Sende- und Empfangsseite basiert, um die Art und Position der zu versorgenden Geräte zu erkennen und sie von anderen leitfähigen Objekten im Sendebereich zu unterscheiden. Die experimentellen Ergebnisse zeigen, dass die vorgeschlagene Architektur eine gute Leistung für verschiedene Trajektorien hat, wenn die Geschwindigkeit der Geräte 15 mm/s nicht überschreitet. Außerdem beträgt die maximale Erkennungszeit für die anfängliche Geräteposition etwa 1,6 s. Das maximale Zeitintervall für die Überprüfung der Senderspulen beträgt etwa 0,7 s.:1. INTRODUCTION 2. THEORETICAL BACKGROUND 3. STATE OF THE ART OF MULTI-COIL IPT SYSTEMS 4. NOVEL DESIGN OF A MULTI-COIL IPT SYSTEM 5. MULTI-COIL ACTIVATION PROCEDURE 6. EXPERIMENTAL INVESTIGATIONS 7. CONCLUSION AND OUTLOO

1-D broadside-radiating leaky-wave antenna based on a numerically synthesized impedance surface

A newly-developed deterministic numerical technique for the automated design of metasurface antennas is applied here for the first time to the design of a 1-D printed Leaky-Wave Antenna (LWA) for broadside radiation. The surface impedance synthesis process does not require any a priori knowledge on the impedance pattern, and starts from a mask constraint on the desired far-field and practical bounds on the unit cell impedance values. The designed reactance surface for broadside radiation exhibits a non conventional patterning; this highlights the merit of using an automated design process for a design well known to be challenging for analytical methods. The antenna is physically implemented with an array of metal strips with varying gap widths and simulation results show very good agreement with the predicted performance

Beam scanning by liquid-crystal biasing in a modified SIW structure

A fixed-frequency beam-scanning 1D antenna based on Liquid Crystals (LCs) is designed for application in 2D scanning with lateral alignment. The 2D array environment imposes full decoupling of adjacent 1D antennas, which often conflicts with the LC requirement of DC biasing: the proposed design accommodates both. The LC medium is placed inside a Substrate Integrated Waveguide (SIW) modified to work as a Groove Gap Waveguide, with radiating slots etched on the upper broad wall, that radiates as a Leaky-Wave Antenna (LWA). This allows effective application of the DC bias voltage needed for tuning the LCs. At the same time, the RF field remains laterally confined, enabling the possibility to lay several antennas in parallel and achieve 2D beam scanning. The design is validated by simulation employing the actual properties of a commercial LC medium