Design and implementation of Radix-3/Radix-2 based novel hybrid SAR ADC in scaled CMOS technologies

This thesis focuses on low power and high speed design techniques for successive approximation register (SAR) analog-to-digital converters (ADCs) in nanoscale CMOS technologies. SAR ADCs’ speed is limited by the number of bits of resolution. An N-bit conventional SAR ADC takes N conversion cycles. To speed up the conversion process, we introduce a radix-3 SAR ADC which can compute 1:6 bits per cycle. To our knowledge, it is the first fully programmable and efficiently hardware controlled radix-3 SAR ADC. We had to use two comparators per cycle due to ADC architecture and we proposed a simple calibration scheme for the comparators. Also, as the architecture of the DAC array is completely different from the architecture of conventional radix-2 SAR ADC’s DAC arrays, we came up with an algorithm for calibration of capacitors of the DAC. Low power SAR ADCs face two major challenges especially at high resolutions: (1) increased comparator power to suppress the noise, and (2) increased DAC switching energy due to the large DAC size. Due to our proposed architecture,the radix-3 SAR ADC uses two comparators per cycle and two differential DACs. To improve the comparator’s power efficiency, an efficient and low cost calibration technique has been introduced. It allows a low power and noisy comparator to achieve high signal-to-noise ratio (SNR). To improve the DAC switching energy, we introduced a radix-3/radix-2 based novel hybrid SAR ADC. We use two single ended DACs for radix-3 SAR ADC and these two single ended DACs can be used as one differential DAC for radix-2 SAR ADC. So, overall, we only have a single DAC as conventional radix- 2 SAR ADC. In addition, a monotonic switching technique is adopted for radix-2 search to reduce the DAC capacitor size and hence, to reduce switching power. It can reduce the total number of unit capacitors by four times. Our proposed hybrid SAR ADC can achieve less DAC energy compared to radix-3 and radix-2 SAR ADCs. Also, to utilize technology scaling, we used the minimum capacitor size allowed by thermal noise limitations. To achieve high resolution, we introduced calibration algorithm for the DAC array. As mentioned earlier, the radix-3 SAR ADC offers higher power than conventional radix-2 SAR ADC because of simultaneous use of two comparators. In the proposed hybrid SAR ADC, we will be using radix-3 search for first few MSB bits. So, the resolution required for radix-3 comparators are much larger than the LSB value of 10-bit ADC. By implementing calibration of comparators, we can use low power, high input referred offset and high speed comparators for radix-3 search. Radix-2 search will be used for rest of the bits and the resolution of the radix-2 comparator has to be less than the required LSB value. So, a high power, low input referred offset and high speed comparator is used for radix-2 search. Also, we introduced clock gating for comparators. So, radix-3 comparators will not toggle during radix-2 search and the radix-2 comparators will be inactive during radix-3 search. By using the aforementioned techniques, the overall comparator power is definitely less than a radix-3 SAR ADC and comparable to a conventional radix-2 SAR ADC. A prototype radix-3/radix-2 based hybrid SAR ADC with the proposed technique is designed and fabricated in 40nm CMOS technology. It achieves an SNDR of 56.9 dB and consumes only 0.38 mW power at 30MS/s, leading to a Walden figure of merit of 21.5 fJ/conv-step.Electrical and Computer Engineerin

Free Speech and Its Relation to Self-Government by Alexander Meiklejohn

In today’s system-on-chip (SoC) implementations, power consumption is a key performance specification. The proliferation of mobile communication devices and distributed wireless sensor networks has necessitated the development of power-efficient analog, radio-frequency (RF), and digital integrated circuits. The rapid scaling of CMOS technology nodes presents opportunities and challenges. Benefits accrue in terms of integration density and higher switching speeds for the digital logic. However, the concomitant reduction in supply voltage and reduced gain of transistors pose obstacles to the design of highperformance analog and mixed-signal circuits such as analog front-ends (AFEs) and data converters. To achieve high DC gain, multistage amplifiers are becoming necessary in AFEs and analog-to-digital converters (ADCs) implemented in the latest CMOS process nodes. This thesis includes the design of multistage amplifiers in 40 nm and 65 nm CMOS processes. An AFE for capacitive body-coupled communication is presented with transistor schematic level results in 40 nm CMOS. The AFE consists of a cascade of amplifiers to boost the received signal followed by a Schmitt trigger which provides digital signal levels at the output. Low noise and reduced power consumption are the important performance criteria for the AFE. A two-stage, single-ended amplifier incorporating indirect compensation using split-length transistors has been designed. The compensation technique does not require the nulling resistor used in traditional Miller compensation. The AFE consisting of a cascade of three amplifiers achieves 57.6 dB DC gain with an input-referred noise power spectral density (PSD) of 4.4 nV/ while consuming 6.8 mW. Numerous compensation schemes have been proposed in the literature for multistage amplifiers. Most of these works investigate frequency compensation of amplifiers which drive large capacitive loads and require low unity-gain frequency. In this thesis, the frequency compensation schemes for high-speed, lowvoltage multistage CMOS amplifiers driving small capacitive loads have been investigated. Existing compensation schemes such as the nested Miller compensation with nulling resistor (NMCNR) and reversed nested indirect compensation (RNIC) have been applied to four-stage and three-stage amplifiers designed in 40 nm and 65 nm CMOS, respectively. The performance metrics used for comparing the different frequency compensation schemes are the unity gain  frequency, phase margin (PM), and total amount of compensation capacitance used. From transistor schematic simulation results, it is concluded that RNIC is more efficient than NMCNR. Successive approximation register (SAR) analog-to-digital converters (ADCs) are becoming increasingly popular in a wide range of applications due to their high power efficiency, design simplicity and scaling-friendly architecture. Singlechannel SAR ADCs have reached high resolutions with sampling rates exceeding 50 MS/s. Time-interleaved SAR ADCs have pushed beyond 1 GS/s with medium resolution. The generation and buffering of reference voltages is often not the focus of published works. For high-speed SAR ADCs, due to the sequential nature of the successive approximation algorithm, a high-frequency clock for the SAR logic is needed. As the digital-to-analog converter (DAC) output voltage needs to settle to the desired accuracy within half clock cycle period of the system clock, a speed limitation occurs due to imprecise DAC settling. The situation is exacerbated by parasitic inductance of bondwires and printed circuit board (PCB) traces especially when the reference voltages are supplied off-chip. In this thesis, a power efficient reference voltage buffer with small area has been implemented in 180 nm CMOS for a 10-bit 1 MS/s SAR ADC which is intended to be used in a fingerprint sensor. Since the reference voltage buffer is part of an industrial SoC, critical performance specifications such as fast settling, high power supply rejection ratio (PSRR), and low noise have to be satisfied under mismatch conditions and over the entire range of process, supply voltage and temperature (PVT) corners. A single-ended, current-mirror amplifier with cascodes has been designed to buffer the reference voltage. Performance of the buffer has been verified by exhaustive simulations on the post-layout extracted netlist. Finally, we describe the design of a 10-bit 50 MS/s SAR ADC in 65 nmCMOS with a high-speed, on-chip reference voltage buffer. In a SAR ADC, the capacitive array DAC is the most area-intensive block. Also a binary-weighted capacitor array has a large spread of capacitor values for moderate and high resolutions which leads to increased power consumption. In this work, a split binary-weighted capacitive array DAC has been used to reduce area and power consumption. The proposed ADC has bootstrapped sampling switches which meet 10-bit linearity over all PVT corners and a two-stage dynamic comparator. The important design parameters of the reference voltage buffer are derived in the context of the SAR ADC. The impact of the buffer on the ADC performance is illustrated by simulations using bondwire parasitics. In post-layout simulation which includes the entire pad frame and associated parasitics, the ADC achieves an ENOB of 9.25 bits at a supply voltage of 1.2 V, typical process corner, and sampling frequency of 50 MS/s for near-Nyquist input. Excluding the reference voltage buffer, the ADC achieves an energy efficiency of 25 fJ/conversion-step while occupying a core area of 0.055 mm2

A 10-bit Charge-Redistribution ADC Consuming 1.9 μW at 1 MS/s

This paper presents a 10 bit successive approximation ADC in 65 nm CMOS that benefits from technology scaling. It meets extremely low power requirements by using a charge-redistribution DAC that uses step-wise charging, a dynamic two-stage comparator and a delay-line-based controller. The ADC requires no external reference current and uses only one external supply voltage of 1.0 V to 1.3 V. Its supply current is proportional to the sample rate (only dynamic power consumption). The ADC uses a chip area of approximately 115--225 μm2. At a sample rate of 1 MS/s and a supply voltage of 1.0 V, the 10 bit ADC consumes 1.9 μW and achieves an energy efficiency of 4.4 fJ/conversion-step

Comparator Design in Sensors for Environmental Monitoring

This paper presents circuit design considerations of comparator in analog-to-digital converters (ADC) applied for a portable, low-cost and high performance nano-sensor chip which can be applied to detect the airborne magnetite pollution nano particulate matter (PM) for environmental monitoring. High-resolution ADC plays a vital important role in high perfor-mance nano-sensor, while high-resolution comparator is a key component in ADC. In this work, some important design issues related to comparators in analog-to-digital converters (ADCs) are discussed, simulation results show that the resolution of the comparator proposed can achieve 5µV , and it is appropriate for high-resolution application

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Low-Power SAR ADCs:Basic Techniques and Trends

With the advent of small, battery-powered devices, power efficiency has become of paramount importance. For analog-to-digital converters (ADCs), the successive approximation register (SAR) architecture plays a prominent role thanks to its ability to combine power efficiency with a simple architecture, a broad application scope, and technology portability. In this review article, the basic design challenges for low-power SAR ADCs are summarized and several design techniques are illustrated. Furthermore, the limitations of SAR ADCs are outlined and hybrid architecture trends, such as noise-shaping SAR ADCs and pipelined SAR ADCs, are briefly introduced and clarified with examples

Power Efficient ADCs for Biomedical Signal Acquisition

Open Access.Peer reviewe