VERIFICATION AND DEBUG TECHNIQUES FOR INTEGRATED CIRCUIT DESIGNS

Verification and debug of integrated circuits for embedded applications has grown in importance as the complexity in function has increased dramatically over time. Various modeling and debugging techniques have been developed to overcome the overwhelming challenge. This thesis attempts to address verification and debug methods by presenting an accurate C model at the bit and algorithm level coupled with an implemented Hardware Description Language (HDL). Key concepts such as common signal and variable naming conventions are incorporated as well as a stepping function within the implemented HDL. Additionally, a common interface between low-level drivers and C models is presented for early firmware development and system debug. Finally, selfchecking verification is discussed for delivering multiple test cases along with testbench portability

SystemVerilog Verification of Wishbone-Compliant Serial Peripheral Interface

Synchronous serial interfaces provide economical on-board communication between the processor, digital to analog and analog to digital converters, memory, and other building blocks on the chip. A number of Integrated Circuit (IC) manufacturers develop and produce components that are compatible with serial interfaces. The common serial interfaces include Serial Peripheral Interface (SPI), Inter-Integrated Circuit (I2C), Universal Asynchronous Receiver Transmitter (UART), and Universal Serial Bus (USB). SPI is widely used and advantageous over other serial interfaces due to its features of simplicity, low cost, clock synchronous, and non-interrupting high-speed data transfer rate. SPI is the core controller of the design. An open source hardware computer bus Wishbone is selected as the host controller enabling parallel data exchange for faster communication. Both the hardware buses employ a master-slave configuration which makes the bus-interfacing easier. This research presents a verification environment using SystemVerilog for the SPI Master device. An existing design from Open Cores is re-used, described as per latest specifications in Verilog at the Register Transfer Level (RTL) and is in conformity with the design-reuse methodology. This paper provides an understanding of the verification, layered test benches, Object-Oriented Technology (OOT), SystemVerilog, SPI features, SPI advantages, disadvantages, and applications, SPI data transmission and transfer formats, SPI registers, SPI sub-system and Wishbone-SPI architecture, and the test bench development methodology. The focus is to understand how OOT and SystemVerilog improve productivity and functional coverage in a verification environment by the use of different constructs, constrained-random techniques, coverage, and assertions. A test bench was developed to verify the SPI master core. Testbench components include a random transaction generator, a Wishbone driver, an SPI master as the design under test, a receiver as the SPI slave, a monitor with tasks to monitor the host and the core, test cases, and a scoreboard to record metrics, assertions and store expected and actual data

Energy-efficient hardware design based on high-level synthesis

This dissertation describes research activities broadly concerning the area of High-level synthesis (HLS), but more specifically, regarding the HLS-based design of energy-efficient hardware (HW) accelerators. HW accelerators, mostly implemented on FPGAs, are integral to the heterogeneous architectures employed in modern high performance computing (HPC) systems due to their ability to speed up the execution while dramatically reducing the energy consumption of computationally challenging portions of complex applications. Hence, the first activity was regarding an HLS-based approach to directly execute an OpenCL code on an FPGA instead of its traditional GPU-based counterpart. Modern FPGAs offer considerable computational capabilities while consuming significantly smaller power as compared to high-end GPUs. Several different implementations of the K-Nearest Neighbor algorithm were considered on both FPGA- and GPU-based platforms and their performance was compared. FPGAs were generally more energy-efficient than the GPUs in all the test cases. Eventually, we were also able to get a faster (in terms of execution time) FPGA implementation by using an FPGA-specific OpenCL coding style and utilizing suitable HLS directives. The second activity was targeted towards the development of a methodology complementing HLS to automatically derive power optimization directives (also known as "power intent") from a system-level design description and use it to drive the design steps after HLS, by producing a directive file written using the common power format (CPF) to achieve power shut-off (PSO) in case of an ASIC design. The proposed LP-HLS methodology reduces the design effort by enabling designers to infer low power information from the system-level description of a design rather than at the RTL. This methodology required a SystemC description of a generic power management module to describe the design context of a HW module also modeled in SystemC, along with the development of a tool to automatically produce the CPF file to accomplish PSO. Several test cases were considered to validate the proposed methodology and the results demonstrated its ability to correctly extract the low power information and apply it to achieve power optimization in the backend flow

Standart-konformes Snapshotting für SystemC Virtuelle Plattformen

The steady increase in complexity of high-end embedded systems goes along with an increasingly complex design process. We are currently still in a transition phase from Hardware-Description Language (HDL) based design towards virtual-platform-based design of embedded systems. As design complexity rises faster than developer productivity a gap forms. Restoring productivity while at the same time managing increased design complexity can also be achieved through focussing on the development of new tools and design methodologies. In most application areas, high-level modelling languages such as SystemC are used in early design phases. In modern software development Continuous Integration (CI) is used to automatically test if a submitted piece of code breaks functionality. Application of the CI concept to embedded system design and testing requires fast build and test execution times from the virtual platform framework. For this use case the ability to save a specific state of a virtual platform becomes necessary. The saving and restoring of specific states of a simulation requires the ability to serialize all data structures within the simulation models. Improving the frameworks and establishing better methods will only help to narrow the design gap, if these changes are introduced with the needs of the engineers and developers in mind. Ultimately, it is their productivity that shall be improved. The ability to save the state of a virtual platform enables developers to run longer test campaigns that can even contain randomized test stimuli. If the saved states are modifiable the developers can inject faulty states into the simulation models. This work contributes an extension to the SoCRocket virtual platform framework to enable snapshotting. The snapshotting extension can be considered a reference implementation as the utilization of current SystemC/TLM standards makes it compatible to other frameworkds. Furthermore, integrating the UVM SystemC library into the framework enables test driven development and fast validation of SystemC/TLM models using snapshots. These extensions narrow the design gap by supporting designers, testers and developers to work more efficiently.Die stetige Steigerung der Komplexität eingebetteter Systeme geht einher mit einer ebenso steigenden Komplexität des Entwurfsprozesses. Wir befinden uns momentan in der Übergangsphase vom Entwurf von eingebetteten Systemen basierend auf Hardware-Beschreibungssprachen hin zum Entwurf ebendieser basierend auf virtuellen Plattformen. Da die Entwurfskomplexität rasanter steigt als die Produktivität der Entwickler, entsteht eine Kluft. Die Produktivität wiederherzustellen und gleichzeitig die gesteigerte Entwurfskomplexität zu bewältigen, kann auch erreicht werden, indem der Fokus auf die Entwicklung neuer Werkzeuge und Entwurfsmethoden gelegt wird. In den meisten Anwendungsgebieten werden Modellierungssprachen auf hoher Ebene, wie zum Beispiel SystemC, in den frühen Entwurfsphasen benutzt. In der modernen Software-Entwicklung wird Continuous Integration (CI) benutzt um automatisiert zu überprüfen, ob eine eingespielte Änderung am Quelltext bestehende Funktionalitäten beeinträchtigt. Die Anwendung des CI-Konzepts auf den Entwurf und das Testen von eingebetteten Systemen fordert schnelle Bau- und Test-Ausführungszeiten von dem genutzten Framework für virtuelle Plattformen. Für diesen Anwendungsfall wird auch die Fähigkeit, einen bestimmten Zustand der virtuellen Plattform zu speichern, erforderlich. Das Speichern und Wiederherstellen der Zustände einer Simulation erfordert die Serialisierung aller Datenstrukturen, die sich in den Simulationsmodellen befinden. Das Verbessern von Frameworks und Etablieren besserer Methodiken hilft nur die Entwurfs-Kluft zu verringern, wenn diese Änderungen mit Berücksichtigung der Bedürfnisse der Entwickler und Ingenieure eingeführt werden. Letztendlich ist es ihre Produktivität, die gesteigert werden soll. Die Fähigkeit den Zustand einer virtuellen Plattform zu speichern, ermöglicht es den Entwicklern, längere Testkampagnen laufen zu lassen, die auch zufällig erzeugte Teststimuli beinhalten können oder, falls die gespeicherten Zustände modifizierbar sind, fehlerbehaftete Zustände in die Simulationsmodelle zu injizieren. Mein mit dieser Arbeit geleisteter Beitrag beinhaltet die Erweiterung des SoCRocket Frameworks um Checkpointing Funktionalität im Sinne einer Referenzimplementierung. Weiterhin ermöglicht die Integration der UVM SystemC Bibliothek in das Framework die Umsetzung der testgetriebenen Entwicklung und schnelle Validierung von SystemC/TLM Modellen mit Hilfe von Snapshots

Design and Verification Environment for High-Performance Video-Based Embedded Systems

In this dissertation, a method and a tool to enable design and verification of computation demanding embedded vision-based systems is presented. Starting with an executable specification in OpenCV, we provide subsequent refinements and verification down to a system-on-chip prototype into an FPGA-Based smart camera. At each level of abstraction, properties of image processing applications are used along with structure composition to provide a generic architecture that can be automatically verified and mapped to the lower abstraction level. The result is a framework that encapsulates the computer vision library OpenCV at the highest level, integrates Accelera\u27s System-C/TLM with UVM and QEMU-OS for virtual prototyping and verification and mapping to a lower level, the last of which is the FPGA. This will relieve hardware designers from time-consuming and error-prone manual implementations, thus allowing them to focus on other steps of the design process. We also propose a novel streaming interface, called Component Interconnect and Data Access (CIDA), for embedded video designs, along with a formal model and a component composition mechanism to cluster components in logical and operational groups that reduce resource usage and power consumption

Implementing a Time Management Unit for the OR1200 Processor.

This thesis presents a Time Management Unit (TMU) that provides assistance to the scheduler and the interrupt handling of a real-time operation system. The unit provides functionality for monitoring task execution time and a mechanism for signalling when a task depletes its resources. This applies to both regular tasks and the handling of sporadic events. By putting the TMU inside a processor core, it has a more predictable impact on the overhead related to task switching. The implemented TMU is tested as a stand-alone unit with a hardware testbench, and then integrated into the OpenRISC 1000 based OR1200 processor as special purpose registers. The behaviour of OR1200 is verified through hardware simulation, using compiled software as input. The Or1ksim instruction-set simulator is modified to include the TMU functionality, which provides a reference point for the behaviour of the altered processor. The real-time operating system FreeRTOS is adapted to utilize the functionality of the TMU. Its behaviour is verified through simulation on Or1ksim, simulated hardware and execution on a Cyclone V FPGA. Analysis of runtime statistics shows that the module is working as expected through all phases of verification, and that it can increase determinism, reliability and user control. Tests have shown that the TMU is able to recover a faulting task from spin-locks and aid in fail-soft operations for software faults. By placing the TMU inside the processor core, a fixed overhead of 131 cycles is achieved during a context switch when no caches are used

Logic Foundry: A Rapid Prototyping Tool for FPGA-based DSP Systems

No abstact submitted. (Also UMIACS-TR-2002-29

Doctor of Philosophy

dissertationElasticity is a design paradigm in which circuits can tolerate arbitrary latency/delay variations in their computation units as well as communication channels. Creating elastic (both synchronous and asynchronous) designs from clocked designs has potential benefits of increased modularity and robustness to variations. Several transformations have been suggested in the literature and each of these require a handshake control network (examples include synchronous elasticization and desynchronization). Elastic control network area and power overheads may become prohibitive. This dissertation investigates different optimization avenues to reduce these overheads without sacrificing the control network performance. First, an algorithm and a tool, CNG, is introduced that generates a control network with minimal total number of join and fork control steering units. Synchronous Elastic FLow (SELF) is a handshake protocol used over synchronous elastic designs. Comparing to its standard eager implementation (that uses eager forks - EForks), lazy SELF can consume less power and area. However, it typically suff ers from combinational cycles and can have inferior performance in some systems. Hence, lazy SELF has been rarely studied in the literature. This work formally and exhaustively investigates the specifi cations, diff erent implementations, and verifi cation of the lazy SELF protocol. Furthermore, several new and existing lazy designs are mapped to hybrid eager/lazy imple-mentations that retain the performance advantage of the eager design but have power and area advantages of lazy implementations, and are combinational-cycle free. This work also introduces a novel ultra simple fork (USFork) design. The USFork has two advantages over lazy forks: it is composed of simpler logic (just wires) and does not form combinational cycles. The conditions under which an EFork can be replaced by a USFork without any performance loss are formally derived. The last optimization avenue discussed in this dissertation is Elastic Bu er Controller (EBC) merging. In a typical synchronous elastic control network, some EBCs may activate their corresponding latches at similar schedules. This work provides a framework for fi nding and merging such controllers in any control network; including open networks (i.e., when the environment abstract is not available or required to be flexible) as well as networks incorporating variable latency units. Replacing EForks with USForks under some equivalence conditions as well as EBC merging have been fully automated in a tool, HGEN. The impact of this work will help achieve elasticity at a reduced cost. It will broaden the class of circuits that can be elasticized with acceptable overhead (circuits that designers would otherwise nd it too expensive to elasticize). In a MiniMIPS processor case study, comparing to a basic control network implementation, the optimization techniques of this dissertation accumulatively achieve reductions in the control network area, dynamic, and leakage power of 73.2%, 68.6%, and 69.1%, respectively

Re-use of tests and arguments for assesing dependable mixed-critically systems

The safety assessment of mixed-criticality systems (MCS) is a challenging activity due to system heterogeneity, design constraints and increasing complexity. The foundation for MCSs is the integrated architecture paradigm, where a compact hardware comprises multiple execution platforms and communication interfaces to implement concurrent functions with different safety requirements. Besides a computing platform providing adequate isolation and fault tolerance mechanism, the development of an MCS application shall also comply with the guidelines defined by the safety standards. A way to lower the overall MCS certification cost is to adopt a platform-based design (PBD) development approach. PBD is a model-based development (MBD) approach, where separate models of logic, hardware and deployment support the analysis of the resulting system properties and behaviour. The PBD development of MCSs benefits from a composition of modular safety properties (e.g. modular safety cases), which support the derivation of mixed-criticality product lines. The validation and verification (V&V) activities claim a substantial effort during the development of programmable electronics for safety-critical applications. As for the MCS dependability assessment, the purpose of the V&V is to provide evidences supporting the safety claims. The model-based development of MCSs adds more V&V tasks, because additional analysis (e.g., simulations) need to be carried out during the design phase. During the MCS integration phase, typically hardware-in-the-loop (HiL) plant simulators support the V&V campaigns, where test automation and fault-injection are the key to test repeatability and thorough exercise of the safety mechanisms. This dissertation proposes several V&V artefacts re-use strategies to perform an early verification at system level for a distributed MCS, artefacts that later would be reused up to the final stages in the development process: a test code re-use to verify the fault-tolerance mechanisms on a functional model of the system combined with a non-intrusive software fault-injection, a model to X-in-the-loop (XiL) and code-to-XiL re-use to provide models of the plant and distributed embedded nodes suited to the HiL simulator, and finally, an argumentation framework to support the automated composition and staged completion of modular safety-cases for dependability assessment, in the context of the platform-based development of mixed-criticality systems relying on the DREAMS harmonized platform.La dificultad para evaluar la seguridad de los sistemas de criticidad mixta (SCM) aumenta con la heterogeneidad del sistema, las restricciones de diseño y una complejidad creciente. Los SCM adoptan el paradigma de arquitectura integrada, donde un hardware embebido compacto comprende múltiples plataformas de ejecución e interfaces de comunicación para implementar funciones concurrentes y con diferentes requisitos de seguridad. Además de una plataforma de computación que provea un aislamiento y mecanismos de tolerancia a fallos adecuados, el desarrollo de una aplicación SCM además debe cumplir con las directrices definidas por las normas de seguridad. Una forma de reducir el coste global de la certificación de un SCM es adoptar un enfoque de desarrollo basado en plataforma (DBP). DBP es un enfoque de desarrollo basado en modelos (DBM), en el que modelos separados de lógica, hardware y despliegue soportan el análisis de las propiedades y el comportamiento emergente del sistema diseñado. El desarrollo DBP de SCMs se beneficia de una composición modular de propiedades de seguridad (por ejemplo, casos de seguridad modulares), que facilitan la definición de líneas de productos de criticidad mixta. Las actividades de verificación y validación (V&V) representan un esfuerzo sustancial durante el desarrollo de aplicaciones basadas en electrónica confiable. En la evaluación de la seguridad de un SCM el propósito de las actividades de V&V es obtener las evidencias que apoyen las aseveraciones de seguridad. El desarrollo basado en modelos de un SCM incrementa las tareas de V&V, porque permite realizar análisis adicionales (por ejemplo, simulaciones) durante la fase de diseño. En las campañas de pruebas de integración de un SCM habitualmente se emplean simuladores de planta hardware-in-the-loop (HiL), en donde la automatización de pruebas y la inyección de faltas son la clave para la repetitividad de las pruebas y para ejercitar completamente los mecanismos de tolerancia a fallos. Esta tesis propone diversas estrategias de reutilización de artefactos de V&V para la verificación temprana de un MCS distribuido, artefactos que se emplearán en ulteriores fases del desarrollo: la reutilización de código de prueba para verificar los mecanismos de tolerancia a fallos sobre un modelo funcional del sistema combinado con una inyección de fallos de software no intrusiva, la reutilización de modelo a X-in-the-loop (XiL) y código a XiL para obtener modelos de planta y nodos distribuidos aptos para el simulador HiL y, finalmente, un marco de argumentación para la composición automatizada y la compleción escalonada de casos de seguridad modulares, en el contexto del desarrollo basado en plataformas de sistemas de criticidad mixta empleando la plataforma armonizada DREAMS.Kritikotasun nahastuko sistemen segurtasun ebaluazioa jarduera neketsua da beraien heterogeneotasuna dela eta. Sistema hauen oinarria arkitektura integratuen paradigman datza, non hardware konpaktu batek exekuzio plataforma eta komunikazio interfaze ugari integratu ahal dituen segurtasun baldintza desberdineko funtzio konkurrenteak inplementatzeko. Konputazio plataformek isolamendu eta akatsen aurkako mekanismo egokiak emateaz gain, segurtasun arauek definituriko jarraibideak jarraitu behar dituzte kritikotasun mistodun aplikazioen garapenean. Sistema hauen zertifikazio prozesuaren kostua murrizteko aukera bat plataformetan oinarritutako garapenean (PBD) datza. Garapen planteamendu hau modeloetan oinarrituriko garapena da (MBD) non modeloaren logika, hardware eta garapen desberdinak sistemaren propietateen eta portaeraren aurka aztertzen diren. Kritikotasun mistodun sistemen PBD garapenak etekina ateratzen dio moduluetan oinarrituriko segurtasun propietateei, adibidez: segurtasun kasu modularrak (MSC). Modulu hauek kritikotasun mistodun produktu-lerroak ere hartzen dituzte kontutan. Berifikazio eta balioztatze (V&V) jarduerek esfortzu kontsideragarria eskatzen dute segurtasun-kiritikoetarako elektronika programagarrien garapenean. Kritikotasun mistodun sistemen konfiantzaren ebaluazioaren eta V&V jardueren helburua segurtasun eskariak jasotzen dituzten frogak proportzionatzea da. Kritikotasun mistodun sistemen modelo bidezko garapenek zeregin gehigarriak atxikitzen dizkio V&V jarduerari, fase honetan analisi gehigarriak (hots, simulazioak) zehazten direlako. Bestalde, kritikotasun mistodun sistemen integrazio fasean, hardware-in-the-loop (Hil) simulazio plantek V&V iniziatibak sostengatzen dituzte non testen automatizazioan eta akatsen txertaketan funtsezko jarduerak diren. Jarduera hauek frogen errepikapena eta segurtasun mekanismoak egiaztzea ahalbidetzen dute. Tesi honek V&V artefaktuen berrerabilpenerako estrategiak proposatzen ditu, kritikotasun mistodun sistemen egiaztatze azkarrerako sistema mailan eta garapen prozesuko azken faseetaraino erabili daitezkeenak. Esate baterako, test kodearen berrabilpena akats aurkako mekanismoak egiaztatzeko, modelotik X-in-the-loop (XiL)-ra eta kodetik XiL-rako konbertsioa HiL simulaziorako eta argumentazio egitura bat DREAMS Europear proiektuan definituriko arkitektura estiloan oinarrituriko segurtasun kasu modularrak automatikoki eta gradualki sortzeko

Fault-based Analysis of Industrial Cyber-Physical Systems

The fourth industrial revolution called Industry 4.0 tries to bridge the gap between traditional Electronic Design Automation (EDA) technologies and the necessity of innovating in many indus- trial fields, e.g., automotive, avionic, and manufacturing. This complex digitalization process in- volves every industrial facility and comprises the transformation of methodologies, techniques, and tools to improve the efficiency of every industrial process. The enhancement of functional safety in Industry 4.0 applications needs to exploit the studies related to model-based and data-driven anal- yses of the deployed Industrial Cyber-Physical System (ICPS). Modeling an ICPS is possible at different abstraction levels, relying on the physical details included in the model and necessary to describe specific system behaviors. However, it is extremely complicated because an ICPS is com- posed of heterogeneous components related to different physical domains, e.g., digital, electrical, and mechanical. In addition, it is also necessary to consider not only nominal behaviors but even faulty behaviors to perform more specific analyses, e.g., predictive maintenance of specific assets. Nevertheless, these faulty data are usually not present or not available directly from the industrial machinery. To overcome these limitations, constructing a virtual model of an ICPS extended with different classes of faults enables the characterization of faulty behaviors of the system influenced by different faults. In literature, these topics are addressed with non-uniformly approaches and with the absence of standardized and automatic methodologies for describing and simulating faults in the different domains composing an ICPS. This thesis attempts to overcome these state-of-the-art gaps by proposing novel methodologies, techniques, and tools to: model and simulate analog and multi-domain systems; abstract low-level models to higher-level behavioral models; and monitor industrial systems based on the Industrial Internet of Things (IIOT) paradigm. Specifically, the proposed contributions involve the exten- sion of state-of-the-art fault injection practices to improve the ICPSs safety, the development of frameworks for safety operations automatization, and the definition of a monitoring framework for ICPSs. Overall, fault injection in analog and digital models is the state of the practice to en- sure functional safety, as mentioned in the ISO 26262 standard specific for the automotive field. Starting from state-of-the-art defects defined for analog descriptions, new defects are proposed to enhance the IEEE P2427 draft standard for analog defect modeling and coverage. Moreover, dif- ferent techniques to abstract a transistor-level model to a behavioral model are proposed to speed up the simulation of faulty circuits. Therefore, unlike the electrical domain, there is no extensive use of fault injection techniques in the mechanical one. Thus, extending the fault injection to the mechanical and thermal fields allows for supporting the definition and evaluation of more reliable safety mechanisms. Hence, a taxonomy of mechanical faults is derived from the electrical domain by exploiting the physical analogies. Furthermore, specific tools are built for automatically instru- menting different descriptions with multi-domain faults. The entire work is proposed as a basis for supporting the creation of increasingly resilient and secure ICPS that need to preserve functional safety in any operating context