Design for testability of a latch-based design

Abstract. The purpose of this thesis was to decrease the area of digital logic in a power management integrated circuit (PMIC), by replacing selected flip-flops with latches. The thesis consists of a theory part, that provides background theory for the thesis, and a practical part, that presents a latch register design and design for testability (DFT) method for achieving an acceptable level of manufacturing fault coverage for it. The total area was decreased by replacing flip-flops of read-write and one-time programmable registers with latches. One set of negative level active primary latches were shared with all the positive level active latch registers in the same register bank. Clock gating was used to select which latch register the write data was loaded to from the primary latches. The latches were made transparent during the shift operation of partial scan testing. The observability of the latch register clock gating logic was improved by leaving the first bit of each latch register as a flip-flop. The controllability was improved by inserting control points. The latch register design, developed in this thesis, resulted in a total area decrease of 5% and a register bank area decrease of 15% compared to a flip-flop-based reference design. The latch register design manages to maintain the same stuck-at fault coverage as the reference design.Salpaperäisen piirin testattavuuden suunnittelu. Tiivistelmä. Tämän opinnäytetyön tarkoituksena oli pienentää digitaalisen logiikan pinta-alaa integroidussa tehonhallintapiirissä, korvaamalla valitut kiikut salpapiireillä. Opinnäytetyö koostuu teoriaosasta, joka antaa taustatietoa opinnäytetyölle, ja käytännön osuudesta, jossa esitellään salparekisteripiiri ja testattavuussuunnittelun menetelmä, jolla saavutettiin riittävän hyvä virhekattavuus salparekisteripiirille. Kokonaispinta-alaa pienennettiin korvaamalla luku-kirjoitusrekistereiden ja kerran ohjelmoitavien rekistereiden kiikut salpapiireillä. Yhdet negatiivisella tasolla aktiiviset isäntä-salpapiirit jaettiin kaikkien samassa rekisteripankissa olevien positiivisella tasolla aktiivisten salparekistereiden kanssa. Kellon portittamisella valittiin mihin salparekisteriin kirjoitusdata ladattiin yhteisistä isäntä-salpapireistä. Osittaisessa testipolkuihin perustuvassa testauksessa salpapiirit tehtiin läpinäkyviksi siirtooperaation aikana. Salparekisterin kellon portituslogiikan havaittavuutta parannettiin jättämällä jokaisen salparekisterin ensimmäinen bitti kiikuksi. Ohjattavuutta parannettiin lisäämällä ohjauspisteitä. Salparekisteripiiri, joka suunniteltiin tässä diplomityössä, pienensi kokonaispinta-alaa 5 % ja rekisteripankin pinta-alaa 15 % verrattuna kiikkuperäiseen vertailupiiriin. Salparekisteripiiri onnistuu pitämään saman juuttumisvikamallin virhekattavuuden kuin vertailupiiri

A survey of scan-capture power reduction techniques

With the advent of sub-nanometer geometries, integrated circuits (ICs) are required to be checked for newer defects. While scan-based architectures help detect these defects using newer fault models, test data inflation happens, increasing test time and test cost. An automatic test pattern generator (ATPG) exercise’s multiple fault sites simultaneously to reduce test data which causes elevated switching activity during the capture cycle. The switching activity results in an IR drop exceeding the devices under test (DUT) specification. An increase in IR-drop leads to failure of the patterns and may cause good DUTs to fail the test. The problem is severe during at-speed scan testing, which uses a functional rated clock with a high frequency for the capture operation. Researchers have proposed several techniques to reduce capture power. They used various methods, including the reduction of switching activity. This paper reviews the recently proposed techniques. The principle, algorithm, and architecture used in them are discussed, along with key advantages and limitations. In addition, it provides a classification of the techniques based on the method used and its application. The goal is to present a survey of the techniques and prepare a platform for future development in capture power reduction during scan testing

Testing for delay defects utilizing test data compression techniques

textAs technology shrinks new types of defects are being discovered and new fault models are being created for those defects. Transition delay and path delay fault models are two such models that have been created, but they still fall short in that they are unable to obtain a high test coverage of smaller delay defects; these defects can cause functional behavior to fail and also indicate potential reliability issues. The first part of this dissertation addresses these problems by presenting an enhanced timing-based delay fault testing technique that incorporates the use of standard delay ATPG, along with timing information gathered from standard static timing analysis. Utilizing delay fault patterns typically increases the test data volume by 3-5X when compared to stuck-at patterns. Combined with the increase in test data volume associated with the increase in gate count that typically accompanies the miniaturization of technology, this adds up to a very large increase in test data volume that directly affect test time and thus the manufacturing cost. The second part of this dissertation presents a technique for improving test compression and reducing test data volume by using multiple expansion ratios while determining the configuration of the scan chains for each of the expansion ratios using a dependency analysis procedure that accounts for structural dependencies as well as free variable dependencies to improve the probability of detecting faults. Finally, this dissertation addresses the problem of unknown values (X’s) in the output response data corrupting the data and degrading the performance of the output response compactor and thus the overall amount of test compression. Four techniques are presented that focus on handling response data with large percentages of X’s. The first uses X-canceling MISR architecture that is based on deterministically observing scan cells, and the second is a hybrid approach that combines a simple X-masking scheme with the X-canceling MISR for further gains in test compression. The third and fourth techniques revolve around reiterative LFSR X-masking, which take advantage of LFSR-encoded masks that can be reused for multiple scan slices in novel ways.Electrical and Computer Engineerin

Design-for-delay-testability techniques for high-speed digital circuits

The importance of delay faults is enhanced by the ever increasing clock rates and decreasing geometry sizes of nowadays' circuits. This thesis focuses on the development of Design-for-Delay-Testability (DfDT) techniques for high-speed circuits and embedded cores. The rising costs of IC testing and in particular the costs of Automatic Test Equipment are major concerns for the semiconductor industry. To reverse the trend of rising testing costs, DfDT is\ud getting more and more important

A Novel and Practical Control Scheme for Inter-Clock At-Speed Testing

The quality of at-speed testing is being severely challenged by the problem that an inter-clock logic block existing between two synchronous clocks is not efficiently tested or totally ignored due to complex test control. This paper addresses the problem with a novel inter-clock at-speed test control scheme, featuring a compact and robust on-chip inter-clock enable generator design. The new scheme can generate inter-clock at-speed test clocks from PLLs, and is feasible for both ATE-based scan testing and logic BIST. Successful applications to industrial circuits have proven its effectiveness in improving the quality of at-speed testing.2006 IEEE International Test Conference, 22-27 October 2006, Santa Clara, CA, US

Transition Faults and Transition Path Delay Faults: Test Generation, Path Selection, and Built-In Generation of Functional Broadside Tests

As the clock frequency and complexity of digital integrated circuits increase rapidly, delay testing is indispensable to guarantee the correct timing behavior of the circuits. In this dissertation, we describe methods developed for three aspects of delay testing in scan-based circuits: test generation, path selection and built-in test generation. We first describe a deterministic broadside test generation procedure for a path delay fault model named the transition path delay fault model, which captures both large and small delay defects. Under this fault model, a path delay fault is detected only if all the individual transition faults along the path are detected by the same test. To reduce the complexity of test generation, sub-procedures with low complexity are applied before a complete branch-and-bound procedure. Next, we describe a method based on static timing analysis to select critical paths for test generation. Logic conditions that are necessary for detecting a path delay fault are considered to refine the accuracy of static timing analysis, using input necessary assignments. Input necessary assignments are input values that must be assigned to detect a fault. The method calculates more accurate path delays, selects paths that are critical during test application, and identifies undetectable path delay faults. These two methods are applicable to off-line test generation. For large circuits with high complexity and frequency, built-in test generation is a cost-effective method for delay testing. For a circuit that is embedded in a larger design, we developed a method for built-in generation of functional broadside tests to avoid excessive power dissipation during test application and the overtesting of delay faults, taking the functional constraints on the primary input sequences of the circuit into consideration. Functional broadside tests are scan-based two-pattern tests for delay faults that create functional operation conditions during test application. To avoid the potential fault coverage loss due to the exclusive use of functional broadside tests, we also developed an optional DFT method based on state holding to improve fault coverage. High delay fault coverage can be achieved by the developed method for benchmark circuits using simple hardware

Testability considerations for implementing an embedded memory subsystem

textThere are a number of testability considerations for VLSI design, but test coverage, test time, accuracy of test patterns and correctness of design information for DFD (Design for debug) are the most important ones in design with embedded memories. The goal of DFT (Design-for-Test) is to achieve zero defects. When it comes to the memory subsystem in SOCs (system on chips), many flavors of memory BIST (built-in self test) are able to get high test coverage in a memory, but often, no proper attention is given to the memory interface logic (shadow logic). Functional testing and BIST are the most prevalent tests for this logic, but functional testing is impractical for complicated SOC designs. As a result, industry has widely used at-speed scan testing to detect delay induced defects. Compared with functional testing, scan-based testing for delay faults reduces overall pattern generation complexity and cost by enhancing both controllability and observability of flip-flops. However, without proper modeling of memory, Xs are generated from memories. Also, when the design has chip compression logic, the number of ATPG patterns is increased significantly due to Xs from memories. In this dissertation, a register based testing method and X prevention logic are presented to tackle these problems. An important design stage for scan based testing with memory subsystems is the step to create a gate level model and verify with this model. The flow needs to provide a robust ATPG netlist model. Most industry standard CAD tools used to analyze fault coverage and generate test vectors require gate level models. However, custom embedded memories are typically designed using a transistor-level flow, there is a need for an abstraction step to generate the gate models, which must be equivalent to the actual design (transistor level). The contribution of the research is a framework to verify that the gate level representation of custom designs is equivalent to the transistor-level design. Compared to basic stuck-at fault testing, the number of patterns for at-speed testing is much larger than for basic stuck-at fault testing. So reducing test and data volume are important. In this desertion, a new scan reordering method is introduced to reduce test data with an optimal routing solution. With in depth understanding of embedded memories and flows developed during the study of custom memory DFT, a custom embedded memory Bit Mapping method using a symbolic simulator is presented in the last chapter to achieve high yield for memories.Electrical and Computer Engineerin

Delay Measurements and Self Characterisation on FPGAs

This thesis examines new timing measurement methods for self delay characterisation of Field-Programmable Gate Arrays (FPGAs) components and delay measurement of complex circuits on FPGAs. Two novel measurement techniques based on analysis of a circuit's output failure rate and transition probability is proposed for accurate, precise and efficient measurement of propagation delays. The transition probability based method is especially attractive, since it requires no modifications in the circuit-under-test and requires little hardware resources, making it an ideal method for physical delay analysis of FPGA circuits. The relentless advancements in process technology has led to smaller and denser transistors in integrated circuits. While FPGA users benefit from this in terms of increased hardware resources for more complex designs, the actual productivity with FPGA in terms of timing performance (operating frequency, latency and throughput) has lagged behind the potential improvements from the improved technology due to delay variability in FPGA components and the inaccuracy of timing models used in FPGA timing analysis. The ability to measure delay of any arbitrary circuit on FPGA offers many opportunities for on-chip characterisation and physical timing analysis, allowing delay variability to be accurately tracked and variation-aware optimisations to be developed, reducing the productivity gap observed in today's FPGA designs. The measurement techniques are developed into complete self measurement and characterisation platforms in this thesis, demonstrating their practical uses in actual FPGA hardware for cross-chip delay characterisation and accurate delay measurement of both complex combinatorial and sequential circuits, further reinforcing their positions in solving the delay variability problem in FPGAs

Techniques for Improving Security and Trustworthiness of Integrated Circuits

The integrated circuit (IC) development process is becoming increasingly vulnerable to malicious activities because untrusted parties could be involved in this IC development flow. There are four typical problems that impact the security and trustworthiness of ICs used in military, financial, transportation, or other critical systems: (i) Malicious inclusions and alterations, known as hardware Trojans, can be inserted into a design by modifying the design during GDSII development and fabrication. Hardware Trojans in ICs may cause malfunctions, lower the reliability of ICs, leak confidential information to adversaries or even destroy the system under specifically designed conditions. (ii) The number of circuit-related counterfeiting incidents reported by component manufacturers has increased significantly over the past few years with recycled ICs contributing the largest percentage of the total reported counterfeiting incidents. Since these recycled ICs have been used in the field before, the performance and reliability of such ICs has been degraded by aging effects and harsh recycling process. (iii) Reverse engineering (RE) is process of extracting a circuit’s gate-level netlist, and/or inferring its functionality. The RE causes threats to the design because attackers can steal and pirate a design (IP piracy), identify the device technology, or facilitate other hardware attacks. (iv) Traditional tools for uniquely identifying devices are vulnerable to non-invasive or invasive physical attacks. Securing the ID/key is of utmost importance since leakage of even a single device ID/key could be exploited by an adversary to hack other devices or produce pirated devices. In this work, we have developed a series of design and test methodologies to deal with these four challenging issues and thus enhance the security, trustworthiness and reliability of ICs. The techniques proposed in this thesis include: a path delay fingerprinting technique for detection of hardware Trojans, recycled ICs, and other types counterfeit ICs including remarked, overproduced, and cloned ICs with their unique identifiers; a Built-In Self-Authentication (BISA) technique to prevent hardware Trojan insertions by untrusted fabrication facilities; an efficient and secure split manufacturing via Obfuscated Built-In Self-Authentication (OBISA) technique to prevent reverse engineering by untrusted fabrication facilities; and a novel bit selection approach for obtaining the most reliable bits for SRAM-based physical unclonable function (PUF) across environmental conditions and silicon aging effects