On the nature and effect of power distribution noise in CMOS digital integrated circuits

The thesis reports on the development of a novel simulation method aimed at modelling power distribution noise generated in digital CMOS integrated circuits. The simulation method has resulted in new information concerning: 1. The magnitude and nature of the power distribution noise and its dependence on the performance and electrical characteristics of the packaged integrated circuit. Emphasis is laid on the effects of resistive, capacitative and inductive elements associated with the packaged circuit. 2. Power distribution noise associated with a generic systolic array circuit comprising 1,020,000 transistors, of which 510,000 are synchronously active. The circuit is configured as a linear array which, if fabricated using two-micron bulk CMOS technology, would be over eight centimetres long and three millimetres wide. In principle, the array will perform 1.5 x 10 to the power of 11 operations per second. 3. Power distribution noise associated with a non-array-based signal processor which, if fabricated in 2-micron bulk CMOS technology, would occupy 6.7 sq. cm. The circuit contains about 900,000 transistors, of which 600,000 are functional and about 300,000 are used for yield enhancement. The processor uses the RADIX-2 algorithm and is designed to achieve 2 x 10 to the power of 8 floating point operations per second. 4. The extent to which power distribution noise limits the level of integration and/ or performance of such circuits using standard and non-standard fabrication and packaging technology. 5. The extent to which the predicted power distribution noise levels affect circuit susceptibility to transient latch-up and electromigration. It concludes the nature of CMOS digital integrated circuit power distribution noise and recommends ways in which it may be minimised. It outlines an approach aimed at mechanising the developed simulation methodology so that the performance of power distribution networks may more routinely be assessed. Finally. it questions the long term suitability of mainly digital techniques for signal processing

From Conventional to Cl-Based Spatial Analysis

Series: Discussion Papers of the Institute for Economic Geography and GIScienc

Investigation into the wafer-scale integration of fine-grain parallel processing computer systems

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This thesis investigates the potential of wafer-scale integration (WSI) for the implementation of low-cost fine-grain parallel processing computer systems. As WSI is a relatively new subject, there was little work on which to base investigations. Indeed, most WSI architectures existed only as untried and sometimes vague proposals. Accordingly, the research strategy approached this problem by identifying a representative WSI structure and architecture on which to base investigations. An analysis of architectural proposals identified associative memory to be general purpose parallel processing component used in a wide range of WSI architectures. Furthermore, this analysis provided a set of WSI-level design requirements to evaluate the sustainability of different architectures as research vehicles. The WSI-ASP (WASP) device, which has a large associative memory as its main component is shown to meet these requirements and hence was chosen as the research vehicle. Consequently, this thesis addresses WSI potential through an in-depth investigation into the feasibility of implementing a large associative memory for the WASP device that meets the demanding technological constraints of WSI. Overall, the thesis concludes that WSI offers significant potential for the implementation of low-cost fine-grain parallel processing computer systems. However, due to the dual constraints of thermal management and the area required for the power distribution network, power density is a major design constraint in WSI. Indeed, it is shown that WSI power densities need to be an order of magnitude lower than VLSI power densities. The thesis demonstrates that for associative memories at least, VLSI designs are unsuited to implementation in WSI. Rather, it is shown that WSI circuits must be closely matched to the operational environment to assure suitable power densities. These circuits are significantly larger than their VLSI equivalents. Nonetheless, the thesis demonstrates that by concentrating on the most power intensive circuits, it is possible to achieve acceptable power densities with only a modest increase in area overheads.SER

An instruction systolic array architecture for multiple neural network types

Modern electronic systems, especially sensor and imaging systems, are beginning to incorporate their own neural network subsystems. In order for these neural systems to learn in real-time they must be implemented using VLSI technology, with as much of the learning processes incorporated on-chip as is possible. The majority of current VLSI implementations literally implement a series of neural processing cells, which can be connected together in an arbitrary fashion. Many do not perform the entire neural learning process on-chip, instead relying on other external systems to carry out part of the computation requirements of the algorithm. The work presented here utilises two dimensional instruction systolic arrays in an attempt to define a general neural architecture which is closer to the biological basis of neural networks - it is the synapses themselves, rather than the neurons, that have dedicated processing units. A unified architecture is described which can be programmed at the microcode level in order to facilitate the processing of multiple neural network types. An essential part of neural network processing is the neuron activation function, which can range from a sequential algorithm to a discrete mathematical expression. The architecture presented can easily carry out the sequential functions, and introduces a fast method of mathematical approximation for the more complex functions. This can be evaluated on-chip, thus implementing the entire neural process within a single system. VHDL circuit descriptions for the chip have been generated, and the systolic processing algorithms and associated microcode instruction set for three different neural paradigms have been designed. A software simulator of the architecture has been written, giving results for several common applications in the field

Methodology for complex dataflow application development

This thesis addresses problems inherent to the development of complex applications for reconfig- urable systems. Many projects fail to complete or take much longer than originally estimated by relying on traditional iterative software development processes typically used with conventional computers. Even though designer productivity can be increased by abstract programming and execution models, e.g., dataflow, development methodologies considering the specific properties of reconfigurable systems do not exist. The first contribution of this thesis is a design methodology to facilitate systematic develop- ment of complex applications using reconfigurable hardware in the context of High-Performance Computing (HPC). The proposed methodology is built upon a careful analysis of the original application, a software model of the intended hardware system, an analytical prediction of performance and on-chip area usage, and an iterative architectural refinement to resolve identi- fied bottlenecks before writing a single line of code targeting the reconfigurable hardware. It is successfully validated using two real applications and both achieve state-of-the-art performance. The second contribution extends this methodology to provide portability between devices in two steps. First, additional tool support for contemporary multi-die Field-Programmable Gate Arrays (FPGAs) is developed. An algorithm to automatically map logical memories to hetero- geneous physical memories with special attention to die boundaries is proposed. As a result, only the proposed algorithm managed to successfully place and route all designs used in the evaluation while the second-best algorithm failed on one third of all large applications. Second, best practices for performance portability between different FPGA devices are collected and evaluated on a financial use case, showing efficient resource usage on five different platforms. The third contribution applies the extended methodology to a real, highly demanding emerging application from the radiotherapy domain. A Monte-Carlo based simulation of dose accumu- lation in human tissue is accelerated using the proposed methodology to meet the real time requirements of adaptive radiotherapy.Open Acces